Stainless steel Pinch clamps are for use with O-ring and ball and socket clamps All sizes except 1236D18 and 1236D20 have screw locking devices. Only screw locking clamps are recommended for O-ring joints. All clamps are made of 304 –18/8 Stainless Steel.

Ring stand consists of enameled steel support base with zinc-plated steel rod (8835B50 series) and 8091C20 series rings of zinc-plated steel with aluminum screw clamp Ring Stands include one each 64, 89, 114 mm rings Ring Stand Listings indicate base dimensions and rod height

One piece pinchcocks molded of autoclavable white polycarbonate Release by thumb pressure 2848W26 Mini Clamp is single position on-off clamp; for use with thin-wall tubing less than 3/16” o.d. 2848W30 Clamp is 15-position ratchet- type for one-hand, stepwise flow control…

OHAUS hand-operated inoculating turntables produce almost concentric circles of bacterial colonies that are evenly distributed across petri dishes. Cast iron turntables are coated with gray baked acrylic enamel. The 76 mm (3") high, small turntable accommodates 100 mm petri dishes. It has…

Multi-purpose UltraJaws Heavy-Duty Clamps feature an innovative closed yoke construction that minimizes contamination and corrosion of internal components. The unique design enables secure gripping and positioning with added strength and durability. Available in both single and dual prong…

Stainless steel electro-polished finish or nickel-plated zinc construction. Double Buret Clamp holds any size buret from micro to 100mL capacity. Simply compress the scissor-like mechanism, insert buret and gently release to grip. Numbers and graduation on buret remain easy to read. For height…

Our deluxe line of two prong burette clamps are made of pressure die casted zinc alloy and are chrome plated. Adjustable to hold up to 60mm OD burettes, these clamps feature double keyed spring type adjustments. Available with an extension rod 8 ¼" (22cm) long, 5/16" (0.8cm) OD, with an overall…

Regular Clamp Holders Stainless steel electro-polished finish or nickel-plated zinc construction. Ideal for holding clamps to lab-frames. Use wherever clamping at 90° is required. Swivel Holders Two rod holders with center swivel capacity allow tilting of clamps at any angle in…

All stainless steel screw mechanism and anodized aluminum top and bottom plates.

Clamps are die casted from aluminum and feature black rubber sleeves for firm gripping of burettes.  The adjustable clamps hold up to 30mm OD burettes which are held in place by the pressure created by the springs.  For use with rods up to 19mm diameter.

A cast iron clamp with nickel plated steel set screws. Sold individually. Available in the following sizes: 2" OD 3" OD 4" OD 5" OD 6" OD

Rod End Connector (2824E29) Holds rods firmly at 90°. Use when semi-permanent installations are required. Comes with two set screws and is precision bored for close fit. S-Connector (2824E33) Clamps lab frame rods at 90° angle. Twin angled screws allow independent rod…

Test tube clamp for all sizes of test tubes. Available with and without finger grips in both Brass Wire and Steel wire with a brass finish. Note: Wooden test tube holder can accommodate test tubes from 12mm to 25mm in diameter.

All-plastic clamp will not rust, corrode or deform Molded in one piece to eliminate sharp edges Autoclavable Allows precise, one hand regulation of fluid flow, from completely open, to restricted flow, to completely closed. Ideal for use with Nalgene laboratory tubing.

0209X58: Tubing Holder for Beakers This polypropylene plastic clip holds flexible tubing steady and fits securely onto the edge of beakers or pitchers up to 1/4" thick. 5.1cm (2") long arm has a hole to accept tubing up to 9.5mm (3/8") O.D. Autoclavable …

Nickel plated steel. Overall length 5".

Heavy cast iron triangular bases with black enamel finish include a zinc plated steel rod.

Burner tri-pod with cast iron ring and nickel plated threaded legs. Sold individually.

Designed to attach to a tabletop or inverted into a recessed hole for flush mounting. Models are available with either a threaded hole completely through the center or with an unthreaded thru-hole. These die-cast units are supplied without rod. Other sizes are available on request with threaded or…