Septa

Compare Tool

Select up to 3 products

1 - 32 of 92
Sort
View
Show
  • MicroLiter offers products for both LC and GC applications.

  • Specially engineered to fit standard taper joints and tubes. Manufactured under white room conditions for extreme cleanliness. Made of a more dense rubber, low extractables and a better fit (50% to 80% on joints) these septa are much less likely to fail in the presence of solvents.

  • 33 mm Septa, Interlock, Butyl Gray

    DWK Life Sciences (Wheaton)

    Septa closure with locking flange for open-top caps. Flat stopper; thin flange Cap size: 33 mm Gray Chlorobutyl/50 septa

  • High Temperature Septa is made of preconditioned PTFE/silicone rubber and is 3.175 mm (0.125 in.) thick. The average life of these septa is up to 100 injections with a 26s gauge needle. The maximum operating temperature is 212° C. Preconditioned PTFE/silicone rubber septa, 3.175 mm…

  • Septa, PTFE/Silicone

    MilliporeSigma

    Feature: temp. limit 250°C

  • Long injection life, pre-pierced for minimal coring. Maximum temperature 400°C. Long injection life septum typically achieves 400 injections without failure, when used with a rounded-tip (Agilent-style) needle and autosampler or needle guide. Ideal for standard manual-injection GC and GC/MS. 3 mm…

  • Butyl Gray Headspace Vial Septa

    National Scientific

    For 20 mm vials Temperature range: 40° to 120°C Does not provide PTFE barrier Not suitable for alkalines, benezene, chlorinated solvents or cyclohexane

  • Septa PTFE Silicone 18-400 Cs144

    DWK Life Sciences (Kimble)

    Excellent for use with open-top caps to access container contents with a syringe Highly chemically resistant PTFE facing maintains integrity of contents Silicone rubber backing allows repeated puncturing through the seal Resists coring Autoclavable Recommended for use in all…

  • Septa PTFE Silicone 24-400 Cs144

    DWK Life Sciences (Kimble)

    Resists coring and is autoclavable. Recommended for use in all auto samplers using screw thread vials. Great for sample storage.

  • 10-425 Septa

    National Scientific

    PTFE Disk septa are chemically inert PTFE Red Rubber septa are economical for many GC applications PTFE/Silicone septa are most popular for HPLC and IC applications Pre-slit septa are easier to pierce with thin gauge needles

  • CL BTO inlet septa 11.5mm 50pk

    Agilent Technologies

  • CL Gray inlet septa 9mm 50pk

    Agilent Technologies

  • 3 Layer Septa

    Hamilton

    Three Layer Septa is made of preconditioned silicone rubber and is 3.81 mm (0.150 in.) thick. The average life of these septa is up to 100 injections with a 26s gauge needle. The maximum operating temperature is 200° C. Preconditioned silicone rubber septa, 3.81 mm (0.15“) thick …

  • Headspace Septa and Stoppers

    Thermo Scientific Sun SRi

    Requires the use of 20mm aluminum seals

  • An improved version over the original Thermogreen LB-1 septa. Extremely low bleed over a wide range of inlet temperatures (100 °C to 350 °C) Already conditioned, ready to use Easier needle penetration and high puncture tolerance (ideal for autosamplers) Rubber formulation…

  • Septa for VOA Vials

    Thermo Scientific Sun SRi

    22 mm Septa for VOA Vials PTFE/Silicone Liner

  • Septa PTFE Rubber 18-400 Cs144

    DWK Life Sciences (Kimble)

    Low cost, good resealability Polytetrafluoroethylene provides barrier for product contact Red rubber

  • 11mm Crimp Seals

    National Scientific

    Aluminum seals with pre-inserted septa are compatible with standard opening crimp top vials, wide opening Target LOVial™ crimp top vials and Target Snap-it™ crimp/snap vials.

  • Septa, 0.005" PTFE/0.120" Sil

    DWK Life Sciences (Kimble)

    Resists coring and is autoclavable. Recommended for use in all auto samplers using screw thread vials. Great for sample storage. 73818A-24 ( 1213T38) is white PTFE/Tan Silicone and is recommended for use with the 40 mL EPA vial.

  • Synonym: rubber caps, rubber stopper, rubber stoppers Usage: for 5-6 mm O.D. tubes and ampules Color:   white General description Engineered for a "push on" fit in NMR tubes and ampules. The unique design provides a penetration point for cannulation and a dual…

  • Merlin Microseal

    Agilent Technologies

    Low bleed, longer life alternative to standard septa for split/splitless injection Has a lifetime of more than 2000 injections, depending on samples and operating conditions Reduced instrument downtime for septa changes and injection port liner changes due to septa particulates Two…

  • Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.

  • GC injection port septa Standard quality Septum grade: Standard septa (ST) Material: beige silicone Thickness: 4 mm Hardness: 60° shore A Septum grade: High temperature septa (HT) Material: red non-bleeding silicone Thickness: 3 mm Hardness: 60° shore A …

  • CL BTO inlet septa SHM Plug 50pk

    Agilent Technologies

  • Septa for screw caps, N 9

    MACHEREY-NAGEL

    Replacement septa for 9 mm screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C,…

  • Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.

  • Sera-Separa®

    Evergreen Scientific

    For use in removing fibrin and macro particles from serum to prevent line clogging. Users insert the 16 mm flange into the evacuated blood tube and push downward. Graduated barrel tells exactly how much liquid has been filtered. Wide-body style prevents sample probes from hitting side walls.

  • BTO Septa

    Chromatography Research Supplies

    Maximum setpoint: 400°C Low bleed Long injection life 3 mm thick CenterGuide™ chamber in one face guide the needle with each injection.

  • CL BTO inlet septa 10mm 100pk

    Agilent Technologies

  • CL Gray inlet septa 10mm 50pk

    Agilent Technologies

  • Material: Red Silicone Septa L x O.D.: 0.308 in. x 0.125 in. Legal Information Mininert is a registered trademark of Valco Instruments Co. Inc.

  • Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.