The MD8 series of air samplers are monitoring devices combined with novel filtration systems for the exceptional recovery of airborne microorganisms. MD8 AirScan: (Integrated) Quantitative detection in sterile areas such as clean rooms/RABS, isolators, or blow-fill-seal machines. …

The ESS Air Sampling Bag incorporates a two opening system for sampling and extraction. The side port/stem (3/16" OD) allows filling with a pneumatic pump and tubing, and for rapid emptying of the bag. The top of the valve is

Hydrion Ammonia Meter Test Paper is designed and calibrated to measure the amount of ammonia in air in parts per million wherever there may be actual or potential ammonia pollution. The color chart has matches at 0-5-10-20-50-100ppm. The Hydrion Ammonia Test Kit is especially useful where…

Accessories for MD8 air sampling devices

With standard U shape gauge made of heavy barometer tubing and mounted on a wooden panel for vertical suspension. The scale is adjustable and accurately calibrated. Supplied with scale and tubes, but without mercury.

Used for sampling air volumes at low jet velocity. Bottle joint is 24/40. Stopper uses #7 Ace-Safe removable hose connections for easy connect/disconnect. Impinger nozzle calibrated to deliver 0.09 to 0.11 CFM at 30.5cm (12") H2O vacuum. Bubbler nozzle has sintered glass filter, porosity A…

Primarily designed for use with ACE 8051 bearings. The inner tube through which the stirring shaft passes, plus the PTFE O-Ring supplied with each unit, prevents the lubricant or foreign particles from contaminating the flask contents. For replacement PTFE ring, order 8113-89.

Automatic, adjustable pressure release valve for safer operation of pilot plant or other assemblies where the pressure is of great concern. The tension on the stainless steel spring determines the amount of pressure needed to force the lower piece open. With the spring supplied, the range is 15-50…

Clean with Eco-Confidence! A new duster from the market leader, the Dust-Off ECO Duster is one of the first to utilize a newly-formulated non-flammable, ultra-low Global Warming Potential (GWP) aerosol propellant. The Dust-Off Eco Duster has been environmentally engineered with the same…

Flexible Non contaminating On/off valve closure Use for gas or liquid sample containment Heat-sealed seams for leak-proof operation Reusable bags made of 2 mil PVDF fluoropolymer film, Chemware® Gas Bags offer an economical alternative for analysis of non-corrosive gases.…

An all-glass check valve with ground seat for liquid seal. Available in style A for vertical use, and style B for right angle connection. Connections are 8mm O.D.

Imhoff sedimentation cone for the determination of settleable matter in water. Either blunt tip or Ace-Thred tip for environmental applications. Graduated from 0-2ml in 0.1ml divisions, 2-10ml in 0.5ml divisions, 10-40ml in 1ml divisions, 40-100ml in 2ml divisions.

Unique impinger designed to be more economical when connecting in series eliminates need for connecting tubes.The 12/5 joints are perpendicular and come directly off bottle 180 degree apart. Screw cap on bottle has PTFE liner. Each bottle has one ball and one socket joint. Capacity 25mL. Bottle is…

Schlenk style flask for vacuum, NO-AIR or gas applications. Can be used for storage or reactions. Top is either a no.15 o-ring or outer standard taper joints. Side arm has either a 0-3 inlet valve or a 2mm or a 4mm glass stopcock.

Schlenk style reaction tube for vacuum and No-Air applications. Available in many capacities, joint sizes and side arm configurations including a glass stopcock, 0-3 inlet valve or a 0-4 Hi-Vac valve.

A high velocity impinger (Ref. AGI-30) which passes 12.0 to 13.0L/min. (corrected to engineering standard gas conditions) when the pressure drop across the orifice is 41cm Hg or greater. Stopper fits 24/25 125ml bottle and features a 11mm OD center tube, 8mm OD side arm with bulge, 0.05in capillary…

Glass Manifold with #15 Ace-Thred at either end to allow switching vacuum connection to left or right side. Supplied with three or five 0 - 4mm High Vacuum, Easy Action Stopcocks for sample ports. Plugs are PTFE with Nylon hooded handles and FETFE O-Rings. Ultimate vacuum of 10 - 7 can be realized…

A high velocity impinger which passes 6L/min (corrected to engineering gas conditions) when the pressure drop across the orifice is 41cm Hg or greater. Stopper fits 24/25 125ml bottle and features a 11mm OD center tube, 8mm OD side arm with bulge, 0.035in capillary tip that is positioned 4mm above…

Identical to 7531-10 with the exception that the nozzle is replaced by a sintered glass filter, porosity A (145-175 microns). Used in determination of Acrolein: 4-Hexylresorcinol Method #1. Bottle has encircling graduations from 0 to 25mL or 0 to 30mL in 5mL divisions. Inlet/ outlet are 7mm O.D.…

Glass Manifold with #15 Ace-Thred at either end To allow switching 5853 vacuum connection to left or right side. Supplied with three or five, 4mm straight bore PTFE stopcock sampling ports. (Additional ports can be ordered.) Overall length of glass manifold is 230mm. Complete item consists of 8763…

Air sampling cane with funnel at one end to avoid water droplets from collecting at edge and being sucked into manifold train. Bulge above the funnel is for glass wool or similar material to allow for filtering of particulates. Codes -22 & -26 feature a #7 Ace-Thred port for introducing calibration…

Sweep elbow, available with one end threaded, the other end reduced for use with 7506 bushing or both ends threaded for use with either 7506 bushing or 5841 coupling.

7493 air sampling cane 6.4mm mesh PTFE screen assembly. Only available for our 25mm OD canes. Place the screen within the retaining ring, unfasten the yoke's nut & bolt, pass the now open yoke around the funnel and then tighten the nut and bolt to secure the assembly. The screen is held in place…

Straight tube type air sampling cane with polyethylene hood and stainless steel brackets. Codes -35 & -37 feature a #7 Ace-Thred port for introducing calibration gases.

Bubbler with either fritted tip or plain orifice stopper. Bottle has 24/40 joint and 10 cm tube below bulge. Stopper has 12/5 outer joint on inlet arm and 12/5 inner on outlet arm. Fritted tip is porosity C (25-50m). Orifice tip is 1.5mm capillary with end tapered. Approximate capacity, with…

A high velocity impinger (Ref. AGI-4) which passes 12.3 to 12.6L/min. (corrected to engineering standard gas conditions) when the pressure drop across the orifice is 41cm Hg or greater. Stopper fits 24/25 125ml bottle and features a 11mm OD center tube, 8mm OD side arm with bulge, 0.05in capillary…