Perfect for the low budget laboratory, this set consists of a HP23-AW portable indicator with 2 probe inputs, one HC2-AW probe for the measurement of product samples, accessories and a carrying case. Battery operated portable indicator with two probe inputs for two simultaneous measurements…

Capacity: 2.2 mL Standard Taper joint: 10/10 Sample is weighed, transferred to the flask and placed in a vacuum oven where the sample is dried at 60°C with a pressure of 5 mm or less of mercury for three hours. The percent loss is then calculated. Method is defined in Code of…

Laboratory Model Automatic Cryoscope for molecular weight, solution concentration, and freezing point depression determinations for aqueous and benzene solutions for 2.0 mL samples, featuring: Two selectable ranges: -2.0 to 0°C and +2.5 to +5.5°C Results displayed in m°C of…

For solvents heavier than water. Used in the method of quantitative separation and determination of glycol mixture by azeotropic distillation described in Analytical Chemistry, Vol. 29, No.1, Page 100. Capacity is 121/2mL, graduated in 0.1mL. Joints are standard taper 24/40.

Suitable for ASTM D 95 and E 123. Subdivided 0.1mL to 2.0mL and 0.2mL above 2mL.

Laboratory Model Automatic Cryoscope for molecular weight, solution concentration, and freezing point depression determinations for aqueous and various solvent solutions for 2.0 mL samples, featuring: 10°C to +10°C Range with 12-position range selector for solvent optimization …

8-in-1 Meter with Patented Built-in IR Thermometer Measure Humidity, Air Temperature (with built-in probe) plus non-contact InfraRed Temperature Pinless moisture sensor allows to monitor moisture in wood and other building materials with no surface damage Remote pin-type probe…

Displays moisture content of wood, wood products, paper or other substances Range: 9.0 to 30.0% Resolution: 0.1%, accuracy ±4% NIST Traceable® Automatic and manual temperature compensation Jumbo sized digits (1 3/8” high) The meter’s memory contains nine material groups such as…

MR01-EXT Use the MR01-EXT for acclimation purposes, such as dryer/dehumidifier exhaust vents. Use the MR01-EXT to extend the reach of the integral temperature/RH sensor on compatible FLIR moisture meters. Probe features an twist locking mechanism. For temperature and real humidity measurements. …

Unique dual LCD displays wall moisture and air temperature simultaneously Moisture content displayed on a relative scale Multi-position pins with safety storage of replaceable pins Easy to operate with selectable side switch (OFF, Test, and Calibrate) Data hold to freeze reading on display …

The MR55 is an affordable tool for moisture remediation and pest control professionals, home or building inspectors, and ?ooring installers. The pin-based meter features wireless connectivity, making it easy to view and share readings from a mobile device. You can also tune the meter to the…

Similar to 7745 but with overflow line to allow excess solvent to return to boiling flask. Used to determine the water content in petroleum and bituminous material. Similar to ASTM Type, except supplied with joints and stopcock to empty measuring tube during the determination. The 10mL size is…

The FLIR MR40 is a rugged 2-pin,‎ single-scale moisture meter with an integrated flashlight for wood and common building materials—ideal for builders,‎ building inspectors,‎ remodelers,‎ moisture remediation technicians,‎ pest control professionals,‎ and residential…

EasyDirect™ Moisture Data Management Software Improve your data management and collect results in an SQL database Connect up to five moisture analyzers (HX204, HS153, HC103)  Filter results and visualize control charts and statistics Export results as PDF, CSV or XML…

Quickly measure the moisture content in wood and other building materials with your choice of Pinless (non-invasive) or Direct Pin method measurement. Using the wireless feature, Bluetooth Datalogging Module (included), and the free ExView W-Series App, you can transmit readings in real-time to…

Features: Quickly indicates the moisture content of materials with Pinless technology without damaging the surface; Remote Pin-type probe (MO290-P included) allows for contact moisture readings (3ft/0.9m cable length) Manually store/recall up to 20 labeled readings Works on multiple wood…

The MR59 is an affordable tool for moisture remediation and pest control professionals, home or building inspectors, and ?ooring installers. The pinless meter features wireless connectivity, making it easy to view and share readings from a mobile device. The MR59’s ball-tip sensor measures…

The MO50 is a compact pin moisture meter. MO50 displays moisture level in wood and building materials such as wall board, sheet rock, cardboard, plaster, concrete and mortar. This product is complete with pins (4), protective cap and 9V battery.

Used in phosphorus determination according to Ind. & Engr. Chem., Anal. Ed., Vol 9, page 524. Receiver capacity 5mL, graduated in 0.05 mL subdivisions. Upper joint is standard taper 24/40, side arm joint, standard taper 45/50.

Moisture test receiver utilizes Ace-Thred bushings to achieve a 45psi @ 100 degrees C pressure rating when used in conjunction with Ace pressure reactors. Graduated receiver in 1ml subdivisions with PTFE bottom outlet stopcock. See also our 6024 series pressure condenser.

Best performance for regulated industries Mettler Toledo has designed the HX204 Excellence Moisture Analyzer to meet the strict demands of research, quality control and production. With a resolution of 0.001%MC and excellent repeatability the HX204 meets the demands of applications requiring…

Take pinless (non-invasive) Moisture measurements on wood and building materials without damaging the surface with the depth of approx. <4" (100mm) with Extech’s MO57 Moisture Meter. The ball moisture sensor provides smooth gliding on hard or delicate surfaces. Easy-to-operate with…

The FLIR MR160 Imaging Moisture Meter is the first of its kind to feature Infrared Guided Measurement (IGM) technology and gives you the power to quickly scan and target moisture issues. IGM visually guides you to the spot where you can make confident moisture measurements. Providing both a…

The FLIR MR60 Moisture Meter Pro is an easy-to-use pin and pinless moisture meter with advanced functionality and a full-color display to meet all your professional measurement needs. An integrated pinless sensor and an external pin probe provide the flexibility to take either destructive or…

Especially useful when heavier than water solvents are employed. A 120 degree, 1:5 PTFE stopcock provides adequate shut-off in the intermediate position. Thermometer joint is 10/30.,/p>

Rugged, reliable and versatile Moisture content RH Dew Point Wet Bulb Ambient Temperature Accurately reads elevated moisture content in various materials for use in building inspection and other industries. Seven material group settings cover various woods, cement,…

The new FLIR MR77 is a durable, all-in-one moisture meter that has the flexibility of both a pin-less sensor and a wired pin probe. The MR77 gives you the ability to take moisture readings as deep as 0.75-inch underneath the surface of a range of wood species and building materials. The meter is…

Used to determine the water content in petroleum and bituminous material. Similar to ASTM Type, except supplied with joints and stopcock to empty measuring tube during the determination. The 10 mL size is subdivided in 0.1mL from 0-1mL, 0.2mL from 1-10mL; 20mL size in 0.1mL from 0-1mL, 0.2mL from…

A complete solution for the Restoration Contractor MO290 - Pinless Moisture Psychrometer + InfraRed Thermometer Monitor moisture in wood and building materials with virtually no surface damage Includes the following contact moisture reading probes: Pin Probe,…

Quick Moisture Measurements on Wood and Building Materials Take quick Moisture measurements on wood and building materials with choice of pin or pinless (non-invasive) method. Easy-to-operate with display icons that indicate the levels of moisture content plus audible alert feature. Ideal…

Large, 1L Barrett type moisture test receiver designed for use with large reactors. 45/50 joints and 60mm distance between the side arm and the body for easy clearance of spherical or cylindrical reactors. 2mm PTFE bottom stopcock and 10ml graduations.