NARROW RESULTS BY
Promotion
Category
Manufacturer
Septa
-
Septa for 20mm Crimp Seals
MicroLiterMicroLiter offers products for both LC and GC applications.
Related Products: Butyl Septa
-
Specially engineered to fit standard taper joints and tubes. Manufactured under white room conditions for extreme cleanliness. Made of a more dense rubber, low extractables and a better fit (50% to 80% on joints) these septa are much less likely to fail in the presence of solvents.
Related Products: Rubber Seal
-
33 mm Septa, Interlock, Butyl Gray
DWK Life Sciences (Wheaton)Septa closure with locking flange for open-top caps. Flat stopper; thin flange Cap size: 33 mm Gray Chlorobutyl/50 septa
Related Products: Butyl Septa
-
High Temperature Septa
HamiltonHigh Temperature Septa is made of preconditioned PTFE/silicone rubber and is 3.175 mm (0.125 in.) thick. The average life of these septa is up to 100 injections with a 26s gauge needle. The maximum operating temperature is 212° C. Preconditioned PTFE/silicone rubber septa, 3.175 mm…
Related Products: High Temperature Septa
-
-
Septa, Long Life GC Autosampler
HamiltonLong injection life, pre-pierced for minimal coring. Maximum temperature 400°C. Long injection life septum typically achieves 400 injections without failure, when used with a rounded-tip (Agilent-style) needle and autosampler or needle guide. Ideal for standard manual-injection GC and GC/MS. 3 mm…
Related Products: Gc Septa
-
Butyl Gray Headspace Vial Septa
National ScientificFor 20 mm vials Temperature range: 40° to 120°C Does not provide PTFE barrier Not suitable for alkalines, benezene, chlorinated solvents or cyclohexane
Related Products: Butyl Septa
-
Septa PTFE Silicone 18-400 Cs144
DWK Life Sciences (Kimble)Excellent for use with open-top caps to access container contents with a syringe Highly chemically resistant PTFE facing maintains integrity of contents Silicone rubber backing allows repeated puncturing through the seal Resists coring Autoclavable Recommended for use in all…
Related Products: Ptfe Silicone Septa
-
Septa PTFE Silicone 24-400 Cs144
DWK Life Sciences (Kimble)Resists coring and is autoclavable. Recommended for use in all auto samplers using screw thread vials. Great for sample storage.
Related Products: Septa Ptfe
-
10-425 Septa
National ScientificPTFE Disk septa are chemically inert PTFE Red Rubber septa are economical for many GC applications PTFE/Silicone septa are most popular for HPLC and IC applications Pre-slit septa are easier to pierce with thin gauge needles
Related Products: Rubber Septa
-
-
-
3 Layer Septa
HamiltonThree Layer Septa is made of preconditioned silicone rubber and is 3.81 mm (0.150 in.) thick. The average life of these septa is up to 100 injections with a 26s gauge needle. The maximum operating temperature is 200° C. Preconditioned silicone rubber septa, 3.81 mm (0.15“) thick …
Related Products: Septa
-
Headspace Septa and Stoppers
Thermo Scientific Sun SRiRequires the use of 20mm aluminum seals
Related Products: Septa Stopper
-
Thermogreen® LB-2 Septa, solid discs
MilliporeSigmaAn improved version over the original Thermogreen LB-1 septa. Extremely low bleed over a wide range of inlet temperatures (100 °C to 350 °C) Already conditioned, ready to use Easier needle penetration and high puncture tolerance (ideal for autosamplers) Rubber formulation…
Related Products: High Temperature Septa
-
Septa for VOA Vials
Thermo Scientific Sun SRi22 mm Septa for VOA Vials PTFE/Silicone Liner
Related Products: Voa Vials
-
Septa PTFE Rubber 18-400 Cs144
DWK Life Sciences (Kimble)Low cost, good resealability Polytetrafluoroethylene provides barrier for product contact Red rubber
Related Products: Septa Ptfe
-
11mm Crimp Seals
National ScientificAluminum seals with pre-inserted septa are compatible with standard opening crimp top vials, wide opening Target LOVial™ crimp top vials and Target Snap-it™ crimp/snap vials.
Related Products: Crimp Seal
-
Septa, 0.005" PTFE/0.120" Sil
DWK Life Sciences (Kimble)Resists coring and is autoclavable. Recommended for use in all auto samplers using screw thread vials. Great for sample storage. 73818A-24 ( 1213T38) is white PTFE/Tan Silicone and is recommended for use with the 40 mL EPA vial.
Related Products: 40 Ml Vial With Septa
-
Synonym: rubber caps, rubber stopper, rubber stoppers Usage: for 5-6 mm O.D. tubes and ampules Color: white General description Engineered for a "push on" fit in NMR tubes and ampules. The unique design provides a penetration point for cannulation and a dual…
Related Products: Rubber Sleeve Stopper
-
Merlin Microseal
Agilent TechnologiesLow bleed, longer life alternative to standard septa for split/splitless injection Has a lifetime of more than 2000 injections, depending on samples and operating conditions Reduced instrument downtime for septa changes and injection port liner changes due to septa particulates Two…
Related Products: Injection Septa
-
Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.
Related Products: Gc Septa
-
Standard quality GC injection port septa
MACHEREY-NAGELGC injection port septa Standard quality Septum grade: Standard septa (ST) Material: beige silicone Thickness: 4 mm Hardness: 60° shore A Septum grade: High temperature septa (HT) Material: red non-bleeding silicone Thickness: 3 mm Hardness: 60° shore A …
Related Products: Injection Septa
-
-
Septa for screw caps, N 9
MACHEREY-NAGELReplacement septa for 9 mm screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C,…
-
Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.
Related Products: Silicone Septa
-
Sera-Separa®
Evergreen ScientificFor use in removing fibrin and macro particles from serum to prevent line clogging. Users insert the 16 mm flange into the evacuated blood tube and push downward. Graduated barrel tells exactly how much liquid has been filtered. Wide-body style prevents sample probes from hitting side walls.
Related Products: Evergreen Tubes
-
-
-
Replacement Septa for Mininert® Valves
MilliporeSigmaMaterial: Red Silicone Septa L x O.D.: 0.308 in. x 0.125 in. Legal Information Mininert is a registered trademark of Valco Instruments Co. Inc.
-
Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.
Related Products: Gc Septa
