Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

An improved version over the original Thermogreen LB-1 septa. Extremely low bleed over a wide range of inlet temperatures (100 °C to 350 °C) Already conditioned, ready to use Easier needle penetration and high puncture tolerance (ideal for autosamplers) Rubber formulation…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Specially engineered to fit standard taper joints and tubes. Manufactured under white room conditions for extreme cleanliness. Made of a more dense rubber, low extractables and a better fit (50% to 80% on joints) these septa are much less likely to fail in the presence of solvents.

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

GC injection port septa Standard quality Septum grade: Standard septa (ST) Material: beige silicone Thickness: 4 mm Hardness: 60° shore A Septum grade: High temperature septa (HT) Material: red non-bleeding silicone Thickness: 3 mm Hardness: 60° shore A …

Replacement septa for 9 mm screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C,…

Single septa for all 20 mm crimp caps from MACHEREY-NAGEL Butyl / PTFE: temperature resistant: –40 °C / +120 °C, medium analytical purity, medium coring, medium hard to penetrate, resealability medium Silicone / PTFE: temperature resistant: –60 °C / +200 °C high…

Single septa for 13-425 screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C, medium…

For use with 12 x 32 mm crimp top vials Large target diameter Available in 4 colors Choice of liner

Excellent for use with open-top caps to access container contents with a syringe Highly chemically resistant PTFE facing maintains integrity of contents Silicone rubber backing allows repeated puncturing through the seal Resists coring Autoclavable Recommended for use in all…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Ideal for use in removing fibrin and macro particles from serum to prevent line clogging. Users insert the 16 mm flange into the evacuated blood tube and push downward. The graduated barrel tells exactly how much liquid has been filtered and the wide-body style prevents sample probes from…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Resists coring and is autoclavable. Recommended for use in all auto samplers using screw thread vials. Great for sample storage.

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

20 mm crimp closure with liner for headspace vials Score lines allow for internal pressure release Choice of three liner options

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…