Chemglass Stirrers
-
FLAKE-FREE Chemically Resistant Maximum 500 RPM; Vacuum (~5 Torr) and Pressure (~3 PSI) Polymer Blend Sleeve Provides Excellent Wear Resistance For Use with Polished Glass, PTFE or Stainless Steel Stirrer Shafts Universal Chem-Vac™ PTFE stirrer bearing provides a VACUUM TIGHT…
-
Stirrer Bearings
ChemglassGrease-Free PTFE stirrer bearing for use under moderate vacuum. The bearing consists of a PTFE standard taper body, Nylon compression cap, PTFE Insert/bushing and a Nylon loosening nut. The PTFE insert/bushing provides only glass and PTFE contact with the reaction. Loosening nut above the standard…
-
PTFE 10mm Stirrer Blades
ChemglassStirrer blade made of 1/8" thick solid PTFE for use with both Chem-Stir™ and button style stirring shafts having a 10mm OD.
-
Chem-Stir™ 10mm Stirring Shafts
ChemglassEliminates Flask Breakage: PTFE is the only contact in the lower radius of the flask, therefore breakage due to dropping the stirrer shaft has been eliminated. Eliminates the Frustration of Assembly: Unique design permits the proper amount of tension to be applied to the blade,…
-
PTFE Covered SS Stirring Shaft
Chemglass10mm O.D. shaft is constructed using a molding process whereas the blade is molded directly onto the PTFE coated stainless steel shaft. This makes the stirrer chemically inert, easy to clean and can be used up to 280°C. The top of the shaft has 50mm of exposed 1/4" diameter stainless steel…
-
Stirrer Plate Stand
ChemglassSupport Stand was designed to accommodate vessels up to 10" diameter, to sit close to the support rod. Support rod is ideal for mounting stirring motors. Each of the four corners rests on a rubber cushion. The powder coated steel base measures 7.875” (200mm) W x 12.5" (316mm) deep…
-
High Viscosity Agitator Stirrer Blades
ChemglassHigh viscosity agitator, made entirely of PTFE and glass filled PTFE, provides excellent stirring at the bottom of 2L through 20L reactors, especially when heavy slurries are being mixed. Agitator attaches to stir shaft by both a compression fitting and a glass filled PTFE safety pin. Heavy…
-
Similar to CG-2070 but with a tooled lubricant cup at the top of the bearing to hold an increased amount of lubricant. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.
-
A 10mm precision ground and polished stirrer shaft to fit CG-2076 and CG-2077 10mm bearings. Side button for attachment of CG-2080 or CG-2081 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF GLASS BEARING. FOR GROUND SHAFTS USED WITH GLASS BEARINGS SEE CG-2075.
-
Macro Glass Stirrer Bearings
ChemglassPrecision bore bearing for use in moderate vacuum with a CG-2074 or CG-2075 ground 10mm stirrer shaft. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.
-
Universal Stirrer Shaft Coupling
ChemglassUniversal Stirrer Shaft Coupling incorporates a universal joint to compensate for misalignment of drive motor and glass stirrer shaft. Nylon bushing compresses around shaft using an allen screw. Steel stud attaches directly to the chuck of a stirrer motor. Supplied complete with an allen wrench. …
-
Stirrer Bearing, PTFE, Chem-Stir™
ChemglassGrease-Free PTFE stirrer bearing designed for use under moderate vacuum applications. The bearing consists of a threaded glass adapter having an inner joint, a set of PTFE washer style bearings, a stainless steel spring, nylon alignment ring and Celcon® compression cap. The unique design of…
-
Stirring Shaft, 10mm, Polished
ChemglassA 10mm precision ground and polished stirrer shaft for use with PTFE bearings and CG-2091 and CG-2092 PTFE agitators. Flat ground section extends half way up shaft and permits positive seating of the PTFE locking screws.
-
Chem-Stir™ PTFE Stirrer Bearings
ChemglassGrease-Free PTFE stirrer bearing designed for use under moderate vacuum applications. The bearing consists of a threaded glass adapter having an inner joint, a set of PTFE washer style bearings, a stainless steel spring, nylon alignment ring and Celcon® compression cap. The unique design of…
-
Stirrer Bearing, PTFE
ChemglassGrease-Free PTFE stirrer bearing designed for use in moderate vacuum applications. Bearing consists of a threaded glass adapter having the listed inner joint, a saddle o-ring, a body bushing with a compression and locking nut, and a precision PTFE inner bearing. The saddle o-ring provides only…
-
Banana Shaped PTFE Stirrer Blades
ChemglassBlade is shaped to resemble the contour of a round bottom flask. Blades are available solid or perforated. Made of 3/16" PTFE to fit 19mm OD stirrer shafts. Minimum joint size listed is the size required to allow passage of the blade.
-
Shaft is precision ground and polished to fit our CG-2076 and CG-2077 10mm PTFE bearings. Designed to be used with cylindrical type reactors. The straight glass blades are spaced 90° apart and angled 15°. PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR COUNTER-CLOCKWISE ROTATION.
-
Stirrer Bearings, Single Neck Flasks
ChemglassPTFE stirrer bearing with a hose connection for vacuum or inert gas source on a single neck flask. Grease-free design has only glass and PTFE in contact with the reaction, and can be used under moderate vacuum applications. Bearing consists of a threaded glass adapter having the listed inner joint…
-
Chem-Stir™ 10mm Polished Stirring Shafts
ChemglassA 10mm OD precision ground and polished stirrer shaft with our patented** Chem-Stir™ blade attachment system. Shaft (C) has been manufactured with a ring at the lower end to permit attachment of the blade (B) with a PTFE nut (D) and bolt (A). Shaft is supplied complete with PTFE nut and bolt…
-
PTFE 60° Agitators
ChemglassAgitator blades are constructed of PTFE with a glass filled PTFE locking nut. This enables them to be attached to the shaft in any vertical position. Note: Designed for use with CG-2079-X, CG-2078-X or CG-2096-X PTFE Covered stainless steel type shafts
-
Chem-Stir™ 19mm Polished Stirring Shafts
ChemglassEliminates Flask Breakage: PTFE is the only contact in the lower radius of the flask, therefore breakage due to dropping the stirrer shaft has been eliminated. Eliminates the Frustration of Assembly: Unique design permits the proper amount of tension to be applied to the blade,…
-
10mm Semi-Micro Stirrer Assembly
ChemglassSemi-micro stirrer has a 10mm OD x 440mm long precision ground button style shaft and a 15 x 46mm TFE blade. Lower end of shaft has a reduced diameter to allow passage through a 19/22 outer joint. The 15 x 46mm blade can be used in flasks having a capacity of 100mL and above. Complete stirrer…
-
Heavy Duty PTFE 19mm Stirrer Blades
ChemglassStirrer blade made of 3/16" thick solid PTFE for use with both Chem-Stir™ and button style stirring shafts having a 19mm OD.
-
Tru-Stir Stirrer Shaft Coupling
ChemglassThe unique design of our Tru-Stir™ stirrer shaft coupling eliminates the need to use rubber hose or universal adapters to attach your stirrer shafts to overhead stir motors. Coupling incorporates a unique helical stainless steel spring permitting up to 1/4” of offset misalignment and…
-
6mm Micro Stirrer Assembly
ChemglassMicro stirrer has a 6mm OD x 305mm long precision ground button style shaft and a football shaped 11 x 33mm TFE blade. The 11 x 33mm blade can be used in flasks having a capacity of 25mL and above. Complete stirrer assembly consists of a shaft, bearing and blade.
-
Shaft is precision ground and polished to fit our CG-2076 and CG-2077 10mm PTFE bearings. Designed to be used with cylindrical type reactors. The curved glass blades are spaced 120° apart and angled upward. PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR COUNTER-CLOCKWISE ROTATION.
-
Shaft is precision ground and polished to fit our CG-2077-H, CG-2077-G and CG-2077-U style 10mm PTFE bearings. Designed to be used with cylindrical type reactors. The curved glass blades are spaced 120° apart and angled upward. PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR CLOCKWISE ROTATION.
-
10mm O.D. shaft is constructed using a molding process whereas the blade is molded directly onto the PTFE coated stainless steel shaft. This makes the stirrer chemically inert, easy to clean and can be used up to 280°C. The top of the shaft has 50mm of exposed 1/4" diameter stainless steel…
-
Jacketed Glass Macro Stirrer Bearings
ChemglassSimilar to CG-2070, but water jacketed to control bearing temperature. For use in moderate vacuum with a CG-2074 or CG-2075 ground 10mm stirrer shaft. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.
-
Features: Compact overall Height Brushless DC motor Micro USB port for Control or Data Logging of RPM/Torque trends RS232 Communication Port Torque Compensation – Maintains set RPM with Viscosity Changes Precise Digital Closed Loop Speed Control: +/- 1.5 RPM CE Rated …
-
J-KEM® Miniature Overhead Stirrers
ChemglassMore power than stirrers ten times its size! Incredible 91in-oz of power yet fits in the palm of your hand! Safety - Low Voltage - Sparkless Sealed motor housing isolates motor from organic vapors Low voltage operation - Sparkless motor runs on 16 volts Convenience - Weighs less than…
-
PTFE Gaskets
ChemglassPTFE gasket is 0.015" thick with an opening to fit Chemglass stirrer shafts. Gasket is placed below the CG-2048 Safety collar to prevent wear as a result of the collar rotating against the stirrer bearing. Also useful as a dust cover.