Stirrer Shaft

Compare Tool

Select up to 3 products

Stirrer Shaft
1 - 32 of 163
Sort
View
Show
  • Polished Glass Stirrer Shafts

    Wilmad LabGlass

    Precision ground and polished, these borosilicate glass stirrer shafts have a 10mm O.D. For use with LG-9475T bearing with PTFE bearing surface, or other bearings with a PTFE interface with the same bore. Features a side button at bottom for attachment of any of the stirrer/stirring blades (LG-9505…

  • Stirrer, Single Shaft

    Troemner

    Ideal for high speed dispersion up to 7500rpm Direct drive Continuous duty Compact design for low torque, high speed mixing. Perfect units for low viscosity mixing. Each is configured with different speed control options. Mixers include collet chuck and 8" (20.3cm) mounting rod…

  • Stirrer Adapter Flex Shaft 8-10mm

    DWK Life Sciences (Kimble)

    A convenient stainless steel universal joint with 5/16 inch OD shaft and polyacetal adapter connects stirrer shafts to stirrer motors. Flexible design allows connection even if alignment is not precise. Stirrer Adapter, Flex-Shaft. For 8-10 mm Shafts

  • Stirrer Bearing, PTFE, 6-10MM Shafts

    Ace Glass

    PTFE stirrer bearing featuring a non-shedding, fully enclosed, anti-whip, chemically resistant design. Models available for 6, 8 and 10mm glass, metal or PTFE stir shafts. Can be used in slight pressure or vacuum applications. Maximum recommended speed for continuous operation is 500 rpm. Unlike…

  • Stirrer Blades, Glass, 10mm Shafts

    Ace Glass

    Glass stir blades for 10mm OD button type stir shafts. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.

  • Stirrer, Model 104A, Double Shaft

    Talboys

    Electronic control of this unit is mounted on top to the motor by a 42” cord 1/8 HP motor provides a maximum torque of 4.7in_lbs Speed range on this stirrer is 1,000 - 7,500 rpm on the direct drive shaft and 100 - 750 rpm on the geared shaft

  • Stirrer, Model 105, Single Shaft

    Talboys

    Constant-speed stirrer which, with the proper propeller selection, can mix over 5 gallons of water Constant speed of 1,550 rpm provides significant agitation to water-like fluids 1/80 HP Non-sparking motor is equipped with thermal overload protection and an on/off switch Although…

  • Stirrer, Model 107, Single Shaft

    Talboys

    Constant-speed stirrer which can mix large amounts of low viscous solutions with the proper propeller selection Speed of 1,600 rpm provides significant agitation to water-like fluids Extremely quiet, non-sparking, 1/30 HP motor is equipped with thermal overload protection and an on/off switch …

  • Stirrer, Model 101, Single Shaft

    Talboys

    Small, economical stirrer, perfect for stirring up to five gallons of water 1/75 HP motor provides a maximum torque of .15 in-lbs Recommended for light duty stirring only Electronic speed control and single shaft motor provide speeds from 500 - 7,500 rpm 1/4” diameter motor shaft

  • Stirrer, Model 102, Double Shaft

    Talboys

    Top mounted Basic Speed Control Provides increased torque with 10:1 gear reduction Offers the capability of two mixing shafts for multiple applications and added versatility Mixes up to two gallons of light weight oils

  • Stirrer Blades Banana Type, PTFE, 10mm Shaft

    Ace Glass

    PTFE banana shaped stir blades for 10mm OD button type stir shafts. 3mm thick blades have a number of perforations and are designed to closely fit various sizes of round bottom flasks. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.

  • Stirrer Blades, PTFE, Oval, 10mm Shafts

    Ace Glass

    PTFE oval stir blades for 10mm OD button type stir shafts. 10mm OD shafts can be found in our 8068, 8070, 8074 and 8075 series.

  • Stirrer Blades, Football Shaped, Stainless, 10mm Shafts

    Ace Glass

    316 stainless steel, football shaped, stir blades for 10mm OD button type stir shafts. Holed versions, codes -70 thru -74, provide even greater agitation. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.

  • Impellers & Shafts for Caframo Overhead Stirrers

    Caframo

    …and shaft in a convenient package. This axial flow impeller is effective for high speed, low to medium viscosity mixing. The 65 mm (2 ½”) diameter­­ blade fixes to an 8 mm (5/16”) diameter shaft with included set screws. Blade and shaft are…

  • Stirrer Accessories, Stirrer Blades

    Dynalon

    Stirrer Blades PTFE construction Fit all standard shafts Will not scratch glassware Hole diameter: 6.5 mm Model 8596G58 to G70 shafts are for use with 8596G18 to G50 blades.

  • Stirring Shaft Coupling

    Ace Glass

    Stir shaft couplings for connecting glass or metal stir shafts to the adjustable chuck on an overhead stir motor. Compression connection is secured to various OD shafts via an Allen screw coupling. The Codes -22 and -24 are complete pass-thru assemblies that enable height adjustment on stir shafts

  • Collar, Stir Shaft

    Ace Glass

    Designed to be used with 8068, 8070, 8071, 8074 or 8078 stirring shafts. Handy for positioning shaft in bearing, and preventing shaft from dropping into flask. Supplied with PTFE gasket to prevent scratching top of bearing and acts as dust cover. Available in either Glass-filled PTFE or 316…

  • Pass-Thru Rod, Flexible shaft

    Ace Glass

    Pass-thru rod for use with Caframo 13565 & 13566 stir motors attached to our 8081 flexible stirring shaft.

  • Stirrer Accessories

    Arrow Engineering

    …(10 mm) diameter motor shafts Keyless Chuck, Nylon-bodied Fits 3/8” (10 mm) diameter motor shafts Adjusts to accept stirrers from 1.5 mm to 10 mm o.d. Couplings Flexible coupling with PTFE sleeve for use with glass stirring shaft The 4"…

  • Stirrer Accessories

    Thermo Scientific Nalgene

    …Autoclavable 8592H36 Lower Assembly/Shaft and Impeller; shaft length x diameter: 13-1/2" x 3/8"; impeller diameter: 4". 8592H39 Lower Assembly is for use with the Nalgene 30-gallon, closed-dome bio tank (9074T60); shaft length x diameter:  30" x 3/8"; impeller…

  • Agitator, PTFE, Multi-Paddle, 10mm Shaft

    Ace Glass

    PTFE multi-paddle agitator for 10mm OD drilled or knob type shafts. Paddles are replaceable. Fits 10mm OD drilled or knob type 8068, 8071 and 8079 shafts.

  • Stirrer Accessories, Blades

    Dynalon

    …range of shaft sizes and lengths Will not scratch or harm glass vessels Usable with most overhead stirrers. Virtually unbreakable Operate at medium to high vacuum Fit standard ground glass joints May be used with all types of standard shaft stirrers in PTFE, glass…

  • Stirring Blade, For 5 & 6mm Shaft

    Ace Glass

    PTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.

  • Agitator, PTFE, Turbine, For 10mm Shaft

    Ace Glass

    …turbine type agitator. Unique locking arrangement assures positive grip. Agitator fits 10 mm shafts. Shaft opening is drilled straight thru to allow positioning of agitator at any drilled position on shaft as well as the bottom. For use with bead type glass shafts, 8068-G, 8075 or PTFE shaft, 8071.

  • Agitator, PTFE, Single Blade, For 19mm Shaft

    Ace Glass

    PTFE agitator with removable blade secured with a PTFE pin. Supplied 3.2x15.2cm blade will fit through a 45/50 joint. Fits 19mm od drilled type or knob type 8076, 8078 & 8079 shafts.

  • Agitator, PTFE, Single Blade, For 10mm Shaft

    Ace Glass

    PTFE agitator with removable blade secured with a PTFE pin. Supplied 76mm long blade will fit through a 29/42 joint. Fits 10mm OD drilled type or beaded type 8068, 8071 and 8075 shafts.

  • STIR-LUBE®,Trubore® Stirrer Lubricant

    Ace Glass

    …which liquefies at body temperature. Because of its composition, you need apply only a very thin film of Stir-Lube® to a stirring shaft to increase bearing and shaft life at least three times over that of a bearing lubricated with glycerine. Non-cooled Ace bearings can be operated at 1500rpm and…

  • Scienceware® Stirrer Blades

    Bel-Art Products

    This strong, non-scratch and inert FDA grade, USP Class VI Teflon® PTFE blade fits all standard button-tip stirring shafts. "Long-groove" keyhole provides easy insertion into flask neck Rotates into proper position for stirring action

  • Precision PTFE Stirrer Bearings

    Wilmad LabGlass

    …not recommended for use with this bearing. Complete 10mm diameter assembly includes PTFE stirrer bearing, PTFE bushing, saddle O-ring (LG-9470-300), threaded heavy wall borosilicate glass adapter, and top cap (LG-10818-114). See LG-9501 for polished stirrer rods or LG-9502 for stainless steel rods.

  • Stirring Shaft Polished, Heavy Duty, 28mm

    Ace Glass

    Heavy duty, 28mm O.D. glass stirring shaft for use with ACE 12845 reactors. Shafts are pre-drilled to accommodate 8091,8093 & 8101 agitators for 28mm od shafts. Recommended for use with either our 8067 Trubore™ bearing with debris trap or our 8050 non-shedding bearing. For motor connection,…

  • RZR Overhead Stirrer Accessories

    Heidolph

    Blades Stainless steel with 400 mm shafts

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.