Ace Glass Stirrers
-
Stirring Shaft, Unground, 9mm
Ace GlassUnground, 9mm OD shaft for use in liquid seal bearings and our debris free 8098 and 8099 stirrer assemblies. Code -25 is a button type shaft which accepts our 8083, 8084, 8085 and 8086 blades. Shaft length accomodates flasks from 500ml to 5000ml.
-
Precision PTFE covered stainless steel stirring shafts, 19mm OD. Drilled type shafts accept 8091,8092,8093,8100 agitators and can be used in 19mm Trubore bearings (8059, 8060, 8061 & 8065). Not recommended for PTFE bearings 8050, 8067 and 13445. Join to stirrer motor using 8124 series chucks.
-
Pass-Thru Rod, Flexible shaft
Ace GlassPass-thru rod for use with Caframo 13565 & 13566 stir motors attached to our 8081 flexible stirring shaft.
-
Stirring Shaft, Unground, 9mm
Ace GlassUnground, 9mm OD stirring shaft design for use with our 9528 vacuum and debris free stirrer assembly. 380mm straight section, 416mm overall length. Use our 9530-08 blade.
-
3/8HP Brushless DC motor for use on pilot plant reactors up ²to 200L. May be used with either the 120V or 240V BLDC ²motor controllers. Supplied with 6ft removable cable and ²mounting hardware.
-
Stirrer, Laboratory, Solid State
Ace GlassTotally enclosed, 1/40hp DC permanent magnet motor with dual 8 mm (5/16") armature and gear shafts with milled flats. Armature shaft with maximum speed of 4000rpm.; 18:1 ratio gear shaft rated 3.6in-lb torque, up to 333rpm. Motor supplied with 1.5 meter 3-wire cable for controller connection.…
-
Precision ground glass stirring shafts, 19mm OD, hollow. Button type shafts accept 8085 blades and can be used in all 19mm ID Trubore 8059, 8060, 8061 and 8065 bearings. Compatible with our 8050 mechanical seal and 13445 PTFE Debris-free bearings. Join to stirrer motor using 8124 series chucks.
-
Agitator, PTFE, Large scale, Turbine
Ace GlassA turbine type agitator, available for 19mm and 28mm shafts. 19mm six blade agitators are open in the center to allow custom positioning on drilled type or knob type 8076, 8078 & 8079 shafts. 28mm four blade agitators are supplied with a PTFE nut & bolt set for securing to 8080 shafts. Shaft is not included.
-
Offset gearbox and motors complete with right angle drive unit for pilot plant systems. Motors with right-angle drive save headspace and work well where height is restricted. Available for standard or hazardous duty applications. Available in either 1/4hp or 1/2hp with a digital 115/230v 50/60Hz…
-
Precision ground, hollow, 5mm glass stirring shaft. Button type shaft accepts 9542 blades and can be used in matching 9524 and 9527 bearings. Holes are provided in the side of the shaft for material introduction and at the bottom for emission into the flask contents. Join to stirrer motor using…
-
With buffered load control and DC filtration. Ratings: AC three-prong output socket, standard NEMA type, 1200 watts. 0 -120 volts, variable, 60 Hz. maximum 10 amps. DC four-prong output socket, cinch type. 360 watts, 0 -150 volts, variable, filtered approximately 1/2 hp.max. 3 amps. A solid state…
-
Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique 3 piece design of Trubore inner bearing, compression seal nylon bushing and glass standard taper adapter allows for moderate misalignment of stir motor and the bearing cannot sieze the shaft. For use with 8077 & 8078 19mm od…
-
Bearing, Trubore, Economy, 6mm
Ace GlassTrubore bearing, heavy duty, standard taper joint, self-aligning. Unique design is forgiving of slight misalignment of stir motor and shaft. Recommended for use with our 9534 6mm precision ground stir shaft.
-
Stir Shaft, 4 Blade Propeller, PTFE
Ace GlassPTFE covered stainless steel shaft with solid PTFE, 4 blade screw propeller. Blades are pitched 45 degrees. For a better grip by the stir motor chuck, 50mm of stainless is left exposed.
-
Stirring bars with large, 25mm (1 inch) raisied center ring.
-
Stirring Shaft, Glass, 19mm, Polished
Ace GlassPolished glass stirring shafts, 19mm OD. Available in solid and hollow styles and in various lengths. Join 8085 blades to button type shafts, Join 8091,8092,8093 and 8100 agitators to either knob or drilled style shafts. Join all shafts to stirrer motor using 8124 series chucks. Recommended for use…
-
Bearing, Trubore, Pressure, 10mm
Ace GlassDesigned for use with #25 Ace-Thred. Consists of a Trubore bearing, pressure bushing, gland with two O-Rings and retainer bushing with o-ring. For use with our precision ground stirring shafts (8068,8070, 8071,8073,9532,9533) and reservoir as part of our 7898 Thin Film reaction system.
-
Motor Controller, Solid State
Ace GlassRated 1 hp. for use with most stirrer motors. Not for use with shunt wound DC motors. A compact, lightweight, solid state, ring stand mountable control unit, both AC and DC outlets. Pulsed AC gives better low speed torque than voltage dropping devices such as rheostat or transformer. AC output: 120…
-
Stirring Shaft, Glass, Polished, 10mm
Ace GlassPolished glass stirring shafts, 10mm OD. Recommended for use with only our 8050,8066,13443 and 13445 bearings. Join 8083,8085,8086,8087,8096 blades to button type shafts. Join 8088, 8089, 8090 & 8091 agitators to bead type shafts. Plain shafts will accept 8094 & 8095 agitators secured with a…
-
Stirrer, Complete
Ace GlassTrubore stirrer assembly consists of the standard taper outer glass bearing, PTFE inner bearing, glass-filled PTFE bushing and lock nut, compression seal saddle o-ring, PTFE blade and either a glass or stainless stir shaft.
-
Bearing, Trubore, Gas Balancing, 10mm
Ace GlassThis bearing is supplied with tubulation for feeding inert gases around the bearing to balance any pressure possibly being developed in the flask. Can also be used for gas-liquid reactions and gas dispersions using our hollow precision ground stirring shafts (8068, 9532).
-
Precision ground glass stirring shafts,10mm OD, crescent type. Useful for stirring viscous materials at low rpm. Available for round bottom flasks of 1, 3 and 5 liters. Code -19, 3 liter size will fit a 2 liter flask, but closely. Flask opening must be 29/42 or larger. Use with Trubore bearings…
-
Stirrer Assembly, Vacuum, Debris Free
Ace GlassRotating ball joint seal gives vacuum-tight connection good into the micron range. Ultimate vacuum is determined primarily by the tightness of the vinyl tubing connector which fastens the unground shaft to the ball member. Operate below 500 rpm. Use with unground stirring shafts (8134,9530).…
-
Bearing, Trubore, 10mm
Ace GlassFor use with Flask Head 9443. By using precision bore tubing throughout the length of the bearing, a stirrer is produced that will hold to within 1mm of vacuum and withstand pressures in the flask up to 300mm. The 9532 Agitator, used with this bearing actually develops a negative pressure of 230mm…
-
Stirring Blade, For 5 & 6mm Shaft
Ace GlassPTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.
-
Stirrer Blades, PTFE, Oval, 10mm Shafts
Ace GlassPTFE oval stir blades for 10mm OD button type stir shafts. 10mm OD shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
Stirring Shaft Coupling
Ace GlassStir shaft couplings for connecting glass or metal stir shafts to the adjustable chuck on an overhead stir motor. Compression connection is secured to various OD shafts via an Allen screw coupling. The Codes -22 and -24 are complete pass-thru assemblies that enable height adjustment on stir shafts…
-
Glass bearing design for use with Ace-Thred pressure reactors and our 8075 glass, polished or 8074 bare, stainless steel 10mm stirring shafts. Both the top bushing and bottom coupling are PTFE. Maximum operating speed is 600 rpm.
-
Precision ground glass stirring shaft with attached vanes, 10mm. For use when agitation and gas introduction are desired at the same time. Agitator will fit through a 45/50 joint. Designed for use with our 9523 Trubore bearing and 9443 or 9446 mini-lab flask heads. Introduced gas exits the hollow…
-
Air Motor, Heavy Duty
Ace GlassA compact, heavy duty air motor with highly damped muffler. Complete unit consists of an air hose with a snap coupling on motor end and shut-off valve on the other. Motor will develop 1.5 hp. at 90 lbs. air pressure. Speeds are variable from 300 to 3000 r.p.m. It consumes approximately 1.98m3 free…
-
Agitator, PTFE, Large Scale Multi-blade
Ace GlassThese heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.
-
Stirrer Blades, PTFE
Ace GlassPTFE stir blades for button type stir shafts. 10mm OD shafts can be found in our product series 8068, 8070, 8074 and 8075. 19mm OD shafts can be found in our 8076 and 8077 series.