Ace Glass
-
Condenser, Spiral
Ace GlassWith spiral condensing tube having both inlet and outlet connections at top, on same side. With joints. Length between joints is approximately 80-90 mm longer than the stated coil length. Available with PTFE clad bottom joint.
-
Round bottom, borosilicate flask with two necks and a side port with either a 2mm glass stopcock or a 0-3 Inlet valve. Excellent flask for reactions and NO-AIR or vacuum applications. Side port is available with either a 2mm glass stopcock or a 0-3 Inlet valve with 8mm end for use of a rubber septa.
-
Flask, Rotary Evaporator/Freeze Drying
Ace GlassDual purpose flask features the TWISTLOR ACE-Seal: simply push adapter head and flask together, turn 90 degrees. Flange on flask has two ground-flats opposite each other that allow Nylon retainers on adapter head to pass over. O-Ring positioned in head
-
Bearing, Trubore, 10mm
Ace GlassFor use with Flask Head 9443. By using precision bore tubing throughout the length of the bearing, a stirrer is produced that will hold to within 1mm of vacuum and withstand pressures in the flask up to 300mm. The 9532 Agitator, used with this bearing actually develops a negative pressure of 230mm…
-
Flask, Single Neck, Flat Bottom
Ace GlassFlat bottom flask featuring a single, short neck with a standard taper outer joint.,/p>
-
Condensers/Coolers, Rotary Evaporator
Ace GlassReplacement, borosilicate glass components for R220 rotary evaporators Product offering includes triple coil condensers, Bullfrog condensers and the lower condensate coolers for rotary evaporators. Available in either plain or safety coated versions. Units include black SVL caps & red GL thread…
-
This bushing adapter has a male Ace-Thred connection at bottom and a female NPT thread drilled into the center of the top of the bushing. The top FNPT connection matches male Swagelok fittings and facilitates joining plastic or metal tubing to Ace-Thred glass fittings and adapters. This adapter is…
-
5 neck flat head with flat ground Duran flange. (1) 90 degree center neck, (1) 90 degree side neck, (2) 10 degree side necks, and (1) 45 degree side neck. For clamp, see product family 6517.
-
Borosilicate glass transition adapter to convert beaded pipe 2 to standard taper joint.
-
-
Distilling Column, Vigreux
Ace GlassWith standard taper 24/40 joints. Length in centimeters refers to the effective length of the column as measured from the lowest to the highest indent of the column.
-
Borosilicate glass, round bottom reaction vessel. Supplied with 24/40 center neck and two 24/40 side necks. Fourth neck is #25 Ace-Thred on 500 mL for use with 7506-10 Bushing and O-Ring; #36 Ace-Thred on 1000 mL and 2000 mL sizes for use with 7506-12 Bushing and O-Ring to make a leak-tight…
-
Adapter, O-Ring Joint to Hose Connection
Ace GlassAdapter, o-ring joint to size E hose connection, fits 3/8"-7/16" id tubing, fetfe o-ring included
-
Chromatographic Column, 1:5 PTFE Plug
Ace GlassChromatographic column with 2mm bore 1:5 taper solid PTFE stopcock plug at bottom.
-
Cell culture shake flask with three bottom edge baffles and three bottom baffles to greatly enhance mixing of cells in suspension and gas transfer to media. Ideal for use with reciprocating baths and shakers. Long style, straight neck accomodates either plastic or stainless steel closures, see Ace…
-
Reaction Flask
Ace GlassWith 4 mm bore stopcock for rapid removal of contents without disturbing the general arrangement of the apparatus. 4 inch ID conical flange requires Ace product family 6496 clamp for securing the head to the flask.
-
Joints, Inner Member, Microscale
Ace GlassStandard taper inner ground joints used in fabrication of ACE Microscale Glassware. Use with 7609 outer member. Codes -11, -12 and -13 have drip tip.
-
Tube, Gas Dispersion
Ace GlassFritted disc is angled approximately 15 degree from stem, which permits the small gas bubbles to rise from the disc surface without excessive formation of large bubbles. These tubes give a performance compared to a horizontal disc, but the method of co
-
Adapter, 75 degree Angle
Ace GlassWith standard taper inner joints at bottom and side, outlet tube at top.
-
NO-AIR storage tube with a 0-4mm Hi-Vac valve top with a 15mm o-ring joint sidearm. The valved top gives the researcher precise flow control and the o-ring joint facilitates connections to Schlenk lines. Supplied with a 7855-726 Fetfe o-ring.
-
Temperature Sensor, J Type
Ace GlassType J temperature probes provide economical measurement from -20 degrees C to 550 degrees C. Probes available sheathed with stainless steel, inconel or simply insulated wire. Code -26 extension will allow the use of a controller up to 8 feet away. See code -27 for extra mini plugs.
-
Instatherm, Erlenmeyer Flask
Ace GlassInstatherm coated, erlenmeyer flask delivers rapid heating up to 250°C. Always use with a temperature controller and never run dry.
-
Funnel, Pressure Filter/Drying, Rusek
Ace GlassUsed for drying air-sensitive compounds with inert gas or a simple pressure filter funnel. O-Ring joint connects cap to body to give a larger opening. Funnel will withstand pressures of 20psi as supplied but NO warranty, expressed or implied. Cap adapt
-
Adapter, Vacuum Take-off
Ace GlassThomas No. 1165A11 14/20 vacuum adapter, 30mm stem below the joint. Thomas No. 1165A12 14/20 vacuum adapter, 175mm stem below the joint. Thomas No. 1165A13 19/22 vacuum adapter, 30mm stem below the joint.
-
Adapter with Ace-Thred
Ace GlassAdapter with ground joint at bottom and either a #11, #15, #25 or #36 Ace-Thred at top.,/p>
-
Beaded Process Pipe
Ace GlassAll pipe is available from stock in lengths shown; special lengths available at slightly higher cost.
-
Bottle, Specific Gravity, Calibrated
Ace GlassGuy-Lussac type calibrated and engraved. Comes complete with stopper and bottle.
-
Bump trap for use between a rotary evaporator's steam tube and evaporator flask, preventing fluid from being drawn into the condenser. Improved design incorporates two drain holes to expedite the return of solvent to the evaporator flask.
-
Air Sampling Cane, with Funnel
Ace GlassAir sampling cane with funnel at one end to avoid water droplets from collecting at edge and being sucked into manifold train. Bulge above the funnel is for glass wool or similar material to allow for filtering of particulates. Codes -22 & -26 feature a #7 Ace-Thred port for introducing calibration…
-
Agitator, PTFE, Multi-Paddle, 10mm Shaft
Ace GlassPTFE multi-paddle agitator for 10mm OD drilled or knob type shafts. Paddles are replaceable. Fits 10mm OD drilled or knob type 8068, 8071 and 8079 shafts.
-
Flask, Round Bottom, Four Neck
Ace GlassRound bottom flask with four necks arranged 3 in-line and one at 90 degrees. 500ml and smaller flasks have angled side necks while larger sizes feature vertical necks. Available in heavy wall.
-