Ace Glass, Chemicals
-
Stirrer Bearing, PTFE, 6-10MM Shafts
Ace GlassPTFE stirrer bearing featuring a non-shedding, fully enclosed, anti-whip, chemically resistant design. Models available for 6, 8 and 10mm glass, metal or PTFE stir shafts. Can be used in slight pressure or vacuum applications. Maximum recommended speed for continuous operation is 500 rpm. Unlike…
-
Distilling Receiver, Jacketed
Ace GlassJacketed receiver with vacuum manifold for removal of sample during operation without disturbing the system. Stopcocks on manifold are 4mm bore, receiver stopcock is 3mm. Hose connections are size E on condenser; 10mm O.D. olive on manifold.
-
Expansion Tank, Rotary Evaporator
Ace GlassBorosilicate glass expansion tank for large scale rotary evaporators. This fits easily into model R220 rotary evaporators. The tank is part of all D Series glass sets. Available in either safety coated or plain versions. Inner DN ball joint inlcudes a size -225 CAPFE o-ring.
-
Heat Transfer Block - Microscale
Ace GlassAluminum heat transfer block, 9594-12 for use in place of a glass sand bath in Microscale experiments. Offers excellent heat transfer and will not interfere with magnetic stirring. Block has four holes for vials and one hole for thermometers. 9594-16 for use on top of stirrer-hot plate to effect…
-
Condenser, Allihn-Kronbitter, No Hold-Up
Ace GlassWith surface of bulbs on one side and the other side flat to permit its use on an angle. With standard taper 24/40 inner and outer joints at top and bottom.
-
Chromatographic column with integral reservoir and #15 Ace-Thred at top, and 2mm bore 1:5 taper PTFE plug at bottom. Column supplied with 7506-06 Nylon bushing and FETFE O-Ring. Complete item consists of column with bushing and O-Ring, and 5853-07 Tubing Connector for connecting 12.5 to 14mm O.D.…
-
Chromatographic Column, 1:5 PTFE Plug
Ace GlassChromatographic column with 2mm bore 1:5 taper solid PTFE stopcock plug at bottom.
-
Condenser, Coiled
Ace GlassDouble jacketed with standard taper inner and outer joint at bottom and top.
-
The DynaBloc heating system supplies low-cost, highly efficient, simultaneous stirring and/or heating of multiple samples contained within various sizes of small, vials and tubes. To anchor blocks to either a 145mm or 135mm diameter hotplate/stirrer, use our 13698-03 (145mm) or 13698-05 (135mm)…
-
Spiral Reflux Condenser
Ace GlassSpiral reflux condenser with inlet and outlet hose barbs located on the same side at the top of the condenser body for easy hose connections. These condensers are available in multiple lengths which allow for greater surface area dependant on the appli
-
Cords, Connecting, Instatherm & UV Lamps
Ace GlassInstatherm connecting cords, codes -16 & -20 feature in-line fuse protection against surges and high voltage. Code -16 fits our earlier style baths, pre 2009, while code -20 features a twist-lok socket used in our current baths. Code -05 fits a wishbone connector commonly used on the lid of…
-
High performance, non-packed, low pressure liquid chromatography columns, epoxy-coated. Simple to assemble, PTFE (no O-rings), safe operation to 150psi with safety shield. Usable with various packing materials chemically inert, zero dead volume, leak free. For analytical or preparative…
-
Stir Shaft, 4 Blade Propeller, PTFE
Ace GlassPTFE covered stainless steel shaft with solid PTFE, 4 blade screw propeller. Blades are pitched 45 degrees. For a better grip by the stir motor chuck, 50mm of stainless is left exposed.
-
Replacement receiving flask adapters for Buchi rotary evaporators. Joins steam tube to receiving flask. Combi-clip not included.
-
PTFE agitator with removable blade secured with a PTFE pin. Supplied 3.2x15.2cm blade will fit through a 45/50 joint. Fits 19mm od drilled type or knob type 8076, 8078 & 8079 shafts.
-
STIR-LUBE®,Trubore® Stirrer Lubricant
Ace GlassA superior, low melting, silicone base lubricant which liquefies at body temperature. Because of its composition, you need apply only a very thin film of Stir-Lube® to a stirring shaft to increase bearing and shaft life at least three times over that of a bearing lubricated with glycerine.…
-
Temperature Controller
Ace GlassTemperature controller ideal for two circuit mantles or general use. Features two front mounted outlets, 16 segment ramp and soak function, fuzzy logic auto tune PID, type 'J' thermocouple, dual 4 digit LED display, universal TC jack for "mini" or "standard" plugs. Unit is downsized, compact and…
-
Stirrer, Laboratory, Solid State
Ace GlassTotally enclosed, 1/40hp DC permanent magnet motor with dual 8 mm (5/16") armature and gear shafts with milled flats. Armature shaft with maximum speed of 4000rpm.; 18:1 ratio gear shaft rated 3.6in-lb torque, up to 333rpm. Motor supplied with 1.5 meter 3-wire cable for controller connection.…
-
Heating Bath Oil, Silicone
Ace GlassAn extremely stable, medium viscosity, silicone oil. Available in two temperature ranges: Low Temp. maximum 180 degree C; or High Temp. maximum 230 degree C. Neither oil shows discoloration after 40 hours at maximum temperature.
-
Agitator, PTFE, Large Scale Multi-blade
Ace GlassThese heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.
-
Support Stand, Bench-Top
Ace GlassStand assembly for 1L to 6L bench reactors. Fits both filter and pressure reactor styles as well as standard round bottom flasks. It will accomodate flasks with or without bottom valves. The motor mount raises and lowers as does the flask support system. This aids in aligning the flask, motor and…
-
The improved design of ACE extractor condensers permits greater condensing capacity, cycling rates may be doubled over conventional style extractors. Complete consists of flask cap, condenser, extractor, and flask.
-
Agitator, PTFE, 4 Blade
Ace Glass4 Blade PTFE agitator available with either 45 or 90 degree blade angle. For use with glass or metal shafts and is secured using a compression style fitting allowing it to positioned anywhere along the length of the shaft.
-
Voltage Controller, 0-120V at 10 Amps
Ace GlassVariable control from zero output to 95% line voltage. A voltage limit rear mounted center-off switch is used to select a 40v or 120v maximum output with the control knob on. 0-10 ammeter 5% accuracy F.S. NOT recommended for heaters rated less than 120 volts. Warning glow light mounted next to…
-
Distilling Receiver
Ace GlassDistilling receiver for use where separate fractions are desired without disturbing distillation pressure. Joints are 24/40. Receiver is 5 mL. Hose connection is size B, for use with 5/16in (7.9mm) or 3/8in (9.5mm) ID tubing. For version with 14/20 joints, or PTFE- clad version with 14/20 joints,…
-
Precision PTFE covered stainless steel stirring shafts, 19mm OD. Drilled type shafts accept 8091,8092,8093,8100 agitators and can be used in 19mm Trubore bearings (8059, 8060, 8061 & 8065). Not recommended for PTFE bearings 8050, 8067 and 13445. Join to stirrer motor using 8124 series chucks.
-
Extractor, Soxhlet
Ace GlassSoxhlet extactor body with standard taper outer joint at top and 24/40 standard taper inner joint at bottom.
-
PTFE agitator with removable blade secured with a PTFE pin. Supplied 76mm long blade will fit through a 29/42 joint. Fits 10mm OD drilled type or beaded type 8068, 8071 and 8075 shafts.
-
Column, Chromatography, Jacketed
Ace GlassColumns are fully jacketed including internally threaded ends for circulation of heat exchange media. A wide choice of upper and lower end pieces can be fitted to columns using 5837, 5838, 5840, 5841, 5842 and 5843 fittings. Available in variety of diameters and lengths. Not for use with 5819 fittings.
-
Vacuum Gauge
Ace GlassA simple form of vacuum gauge, not mounted, but supplied with graduated scale. Mercury NOT supplied.
-
Bearing, Trubore, 5 & 6mm
Ace GlassTrubore bearing with standard taper joint for use with our 9534, 9535 and 9541 precision ground stir shafts. Lubricant well at top will accept enough 8117 Stir-Lube to provide hours of operation at up to 1000 rpm. Match bearing ID with stir shaft OD.
-
Condenser, Dewar Type
Ace GlassDewar type condenser for use with dry ice or other solid cooling agents. Upper tube is 12mm O.D. At bottom is standard taper 24/40 inner joint.