Ace Glass, Chemicals
-
Stirring Blade, For 5 & 6mm Shaft
Ace GlassPTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.
-
Glass bearing design for use with Ace-Thred pressure reactors and our 8075 glass, polished or 8074 bare, stainless steel 10mm stirring shafts. Both the top bushing and bottom coupling are PTFE. Maximum operating speed is 600 rpm.
-
Concentric Tube Column
Ace GlassA high efficiency, low holdup, low pressure drop fractionating column, vacuum jacketed with observation stripe. Suitable for samples as small as 2mL. Center tube is removable for cleaning. Double expansion spiral eliminates choking. Joints are 14/20. A
-
No Hold Up condenser with standard taper 24/40 inner and outer joint at bottom and top, #7 Ace-Thred inlet/outlet for connecting Ace-Safe hose connections with barb for 1/4" I.D. tubing. For replacement hose connections, see 5853. Complete item include
-
Heat Transfer Block - Microscale
Ace GlassAluminum heat transfer block, 9594-12 for use in place of a glass sand bath in Microscale experiments. Offers excellent heat transfer and will not interfere with magnetic stirring. Block has four holes for vials and one hole for thermometers. 9594-16 for use on top of stirrer-hot plate to effect…
-
Replacement condenser for Buchi rotary evaporators. Available plain or safety coated. Includes PTFE hose barbs,GL caps and plug.
-
Condenser, Cold Finger
Ace GlassCold Finger accessory for standard Allihn type condensers. This cold finger has a 24/40 inner joint that fits inside the condenser's upper outer joint and tube to provide added cooling ability and faster condensation. Fits into 5943, 5945, and 5946 con
-
For use as column end fitting that allows connection of appropriate size Ace-Thred to tubing connectors with NPT threads. Available in various Ace-Thred and NPT sizes. Most come complete with both a 100 micron and a 350 micron polyethylene filter.
-
Flexible, immersion or implantable microprobes, Type J, K, and T (for low temperatures). Three foot long wire lead, isolated electrically, is PTFE covered and can be assembled into septum, etc. using needle supplied. Maximum operating temperature of microprobe is 150 degree C .
-
The DynaBloc heating system supplies low-cost, highly efficient, simultaneous stirring and/or heating of multiple samples contained within various sizes of small, vials and tubes. To anchor blocks to either a 145mm or 135mm diameter hotplate/stirrer, use our 13698-03 (145mm) or 13698-05 (135mm)…
-
Septa
Ace GlassThe Ace Glass septa is made from strong rubber for durability and is ideal for sealing columns in laboratories. This septa is designed to use with 24/40 joints. Application: For Sealing Column Ends
-
Condenser, Coiled
Ace GlassCoiled condensing tube, with 24/40 inner and outer joint at bottom and top. Available in various lengths with hose barbs or Ace-Safe connectors.
-
Distilling Receiver, Jacketed
Ace GlassJacketed receiver with vacuum manifold for removal of sample during operation without disturbing the system. Stopcocks on manifold are 4mm bore, receiver stopcock is 3mm. Hose connections are size E on condenser; 10mm O.D. olive on manifold.
-
Adapter, Adjustable Electrode, Ace-Thred
Ace GlassThreaded adapter for use with platinum or other electrodes that normally would be step sealed to glass. With threaded bushing and silicone rubber septum for sealing, the electrode may be adjusted for depth or removed if desired. Capillary of glass is 11/2-2mm with 76mm of stem for sealing to…
-
Clamp, Rod mounted, Swing Latch
Ace GlassBolt latch clamp secures the top of Scale-Up Series™ reaction flask to our stand.
-
Condenser, Friedrichs
Ace GlassWith molded spiral condensing surface and joint at bottom and top. Jacket length 250mm. Available in various joint sizes with hose barbs or Ace-Safe connectors.
-
Air Motor, Heavy Duty
Ace GlassA compact, heavy duty air motor with highly damped muffler. Complete unit consists of an air hose with a snap coupling on motor end and shut-off valve on the other. Motor will develop 1.5 hp. at 90 lbs. air pressure. Speeds are variable from 300 to 3000 r.p.m. It consumes approximately 1.98m3 free…
-
Condenser, Dewar
Ace GlassFor use with dry ice and other solid cooling agents. Can also be adapted for use as a small constant temperature bath by using a constant boiling liquid. In this manner, can also be used as an oil bath. The larger size will hold 100mL flask, small size
-
Adapter, Thermometer, 10/20
Ace GlassMade of PTFE with Nylon knurled nut to adapt standard chemical thermometers. For use in 10/18 or 10/30 joints. Simple to use: insert thermometer to desired depth, tighten nut.
-
Condenser, Air Reflux
Ace GlassMicroscale air condenser normally used in reflux experiments. When packed with desiccant material, condenser becomes a drying tube. With inner joint at bottom, outer joint at top. Codes -10, -14 and -17 supplied with drip tip for use with 9595 Spinning Band Column. Effective length, approximately…
-
76cm Safety Shield
Ace GlassWeighted, all transparent safety shield for laboratory worker protection. Polycarbonate shield is 4.7mm(3/16") thick. Three-sided construction provides stability and protects personnel from front and sides. Heavy steel perimeter base is 25mm x 48mm (1" x 1 1/2"), coated with green…
-
Rapid Preparative Chromatography System
Ace GlassRapid preparative chromatography system suitable for use to pressures of 50 psig, operation behind a shield is recommended. Resevoir is 2L or 3L capacity, epoxy coated and pressure tested. Complete item includes:Brass or glass manifold, pressure gauge, pressure relief valve, column, tubing, and…
-
3/8HP Brushless DC motor for use on pilot plant reactors up ²to 200L. May be used with either the 120V or 240V BLDC ²motor controllers. Supplied with 6ft removable cable and ²mounting hardware.
-
Photochemical Safety Reaction Cabinet
Ace GlassSteel cabinet for safe operation of Photochemical Reaction Equipment. Cabinet has welded seams, fully hinged door with lip to prevent light from escaping. Door has key lock and controls a safety switch that prevents lamp operation unless door is closed. Sealed floor to 1" height to contain any…
-
Condensers/Coolers, Rotary Evaporator
Ace GlassReplacement, borosilicate glass components for R220 rotary evaporators Product offering includes triple coil condensers, Bullfrog condensers and the lower condensate coolers for rotary evaporators. Available in either plain or safety coated versions. Units include black SVL caps & red GL thread…
-
Float, Polyethylene
Ace GlassUsed on top of column packing to prevent turbulence caused by drop-wise addition. Six per pkg.
-
Simple absorption chromatography column for rapid preparative separations with moderate resolution. Allows separations of samples from 0.01 to 10.0g3 in 10-15 minutes. Column and reservoir, only, are Epoxy Coated. Reservoir connects between column and flow control adap-ter. Joints on column,…
-
Distilling Column, Vigreux
Ace GlassLength in millimeters refers to the effective length of the column as measured from the lowest to the highest indent of the column. Available in a microscale version, top center joint is 14/10 externally threaded for making an O-Ring-Cap-Seal type conn
-
Hickman-Hinkle Still, Column
Ace GlassMicroscale Hickman-Hinkle Still Head, Spinning Column. Still head, available with/without side port, is used to carry out simple & fractional distillations. Head has an elongated section below well to accommodate a PTFE spinning band for yields of 6-10 theoretical plates. Still has top 14/10…
-
Condenser, Cold Finger
Ace GlassCold Finger accessory for standard distilling heads and systems. This cold finger has an inner joint that fits inside the upper outer joint and tube to provide added cooling ability and faster condensation. Fits into 6606, 6609, and 6613 distillation h
-
Condenser, Coil Reflux, Microscale
Ace GlassHigh efficiency coil condenser especially suited for vacuum applications. Coil length is 70mm. With 14/10 inner and outer joints; outer joint is externally threaded to allow an O-RING-CAP-SEAL connection with mating inner joint. Supplied with cap and O-Ring.
-
Column, Chromatography
Ace GlassRugged columns with internally threaded ends to which a wide choice of upper and lower end pieces can be fitted using 5837, 5838, 5841, 5842, and 5843 fittings. Available in a variety of lengths and diameters. Some sizes available with epoxy coating for added protection against scratches.