Glass Tubing, Tubing, Supplies
-
Adapter, Feed Tube, Septum
Ace GlassThreaded both ends and with additional #7 threaded side opening for introduction of samples by hypodermic syringe. #7 thread at top is supplied with 5029 Nylon bushing and Fetfe O-ring for use with 5831, 5832 adjustable feed tubes. Size listed is Ace-thred designation which refers to I.D. of tubing…
-
10mm O.D. Thin Walled Precision NMR Tubes
SP Wilmad-LabGlassTo maximize SNR, Precision NMR Tubes have minimal paramagnetic impurities that would impact shimming. Tight ID and OD tolerance as small as 0.0065mm accommodates Wilmad inserts. Manufactured in a state-of-the-art ISO 9001:2008 USA facility using a unique precision shrinking and grinding…
-
Screw Cap EPR Sample Tubes
SP Wilmad-LabGlassNow, sample tubes and storage vials have been joined! Save time and money with the Screw Cap EPR Tube; each come with a PTFE/Silicone Septum.
-
5mm O.D. Thin Walled Economy NMR Tubes
SP Wilmad-LabGlassDesigned for routine use in all NMR spectrometers, Wilmad Economy NMR Tubes are guaranteed to fit tightly in any spinner turbine and have zero NMR background. Best OD tolerance in the industry and a 30% thicker wall than any competitors' product Manufactured in an ISO 9001:2008 USA…
-
-
Multi-Tube Jet Solvent NMR/EPR Tube Washer and Dryer
SP Wilmad-LabGlassWilmad’s 2nd generation Multi-Tube Jet Solvent Washer/Dryer is recommended for research labs that routinely clean NMR and EPR tubes; a single unit can accommodate up to 5 tubes (3, 4 and 5 mm OD) at once. When an inverted tube is inserted onto the solvent transfer tubing and the open end is…
-
5mm O.D. Heavy Walled Precision NMR Tubes
SP Wilmad-LabGlassTo maximize SNR, Precision NMR Tubes have minimal paramagnetic impurities that would impact shimming. Tight ID and OD tolerance as small as 0.0065mm accommodates Wilmad inserts. Manufactured in a state-of-the-art ISO 9001:2008 USA facility using a unique precision shrinking and grinding…
-
These Capillary Gas Delivery Tubes are replacement parts for the 6949M series of PYREX® microchemistry kits.
-
Feed Tube, Luer Tip
Ace GlassPermits packing of column without excessive drop impact. Also used for side arm introduction of effluent or may be used for pressurized operation. Used in conjunction with 5029 Nylon bushing. Supplied straight only. Tube is 8 mm O.D. with luer connection.
-
4mm O.D. Thin Walled Precision NMR Tubes
SP Wilmad-LabGlassTo maximize SNR, Precision NMR Tubes have minimal paramagnetic impurities that would impact shimming. Tight ID and OD tolerance as small as 0.0065mm accommodates Wilmad inserts. Manufactured in a state-of-the-art ISO 9001:2008 USA facility using a unique precision shrinking and grinding…
-
United Scientific™ Glass Tubing Cutter
United Scientific SuppliesCut glass tubes easily and safely. This handy tool allows you to cut glass tubes up to 1.5” in diameter. The spring holds the cutting wheel open so this can easily be operated with one hand. Spring loaded. Easy one-handed operation.
-
10mm O.D. Economy NMR Tubes
SP Wilmad-LabGlassWilmad-LabGlass 10 mm Economy NMR Tubes are manufactured from borosilicate glass that meets the ASTM Type 1 Class B standard and recognized as N51A. Due to its nature, this glass has much less thermal-shock resistance than Class A glass used for our Precision Tubes. It may contain Fe2O3 which is…
-
304 Stainless Steel adapter for matching glass beaded process pipe to male NPT fittings, gauges and flanges.
-
Made of a low expansion borosilicate composition with high chemical resistance Meets all U.S. pharmacopoeia specifications for Type 1A glass 4 to 32mm O.D. sizes are 1219mm long ± approximately 6mm. 4mm O.D. have ends cut, while 5 to 32mm sizes have ends fire polished. 35 to 178mm…
-
Rotor and Caps for Bruker® MAS Probe
SP Wilmad-LabGlassManufactured from the highest purity Zirconia, Wilmad MAS Rotors provide the ultimate solution for analysis of solid samples. Caps fitted with O-rings for improved sealing MAS Probe and caps are 100% compatible for most solid state NMR spectrometers Thoroughly inspected before and…
-
14 psi rated, graduated, netted clear or plastic coated solvent reservoir bottles featuring an Omnifit, 3-valve cap. Only PTFE & Tefzel wetted surfaces. Individually controlled valves permit the application of gas under pressure for venting, flushing,
-
SYNTHWARE NMR Tube Washer
Kemtech AmericaWith 24/40 inner joint and 10mm hose connection. For 5mm NMR tube only. The NMR tube is inserted into the tube cleaner with its plastic cap placed on the closed end to provide support and a vacuum seal. The washing solvent is sequentially added through the side tube while a vacuum is applied…
-
Beaded Pipe To Sanitary Flange Adapter
Ace GlassTransition adapter to convert beaded pipe to sanitary flange. Available in 304 stainless steel or virgin PTFE.
-
Economy Single Tube Solvent Jet Washer/Cleaner
SP Wilmad-LabGlassAfter fitting the washer to a filter flask, an inverted sample tube is inserted into the washer and solvent is introduced into the reservoir using a series of wash bottles. You can perform numerous wash steps and finish by pulling air through the tube to complete the procedure. Filter flasks…
-
Pyrex® NMR Capillary Tubes
SP Wilmad-LabGlassWilmad’s WG-1364 series capillary tubes are sealed at one end and provide a low cost solution for small volume NMR measurement. Made of ASTM Type 1 Class A glass Tested at 400 MHz field
-
5mm O.D. Thin Walled Precision NMR Tubes
SP Wilmad-LabGlassTo maximize SNR, Precision NMR Tubes have minimal paramagnetic impurities that would impact shimming. Tight ID and OD tolerance as small as 0.0065mm accommodates Wilmad inserts. Manufactured in a state-of-the-art ISO 9001:2008 USA facility using a unique precision shrinking and grinding…
-
8mm O.D. Thin Walled Precision NMR Tubes
SP Wilmad-LabGlassTo maximize SNR, Precision NMR Tubes have minimal paramagnetic impurities that would impact shimming. Tight ID and OD tolerance as small as 0.0065mm accommodates Wilmad inserts. Manufactured in a state-of-the-art ISO 9001:2008 USA facility using a unique precision shrinking and grinding…
-
Sample Tube
Ace GlassDesigned by Dr. H.R. Krouse, University of Calgary, for use with 7408 in H2O18/H2O16 determinations. CO2 from the equilibration flask is transferred to the sample tube for isotopic analysis. Unit consists of PTFE plug with FETFE O-Ring and glass vessel with 5mL tube at bottom.
-
COLUMN CHROM FRTD 22X300MM
SP Wilmad-LabGlassInside Height 22.0 millimeters Item Weight 1.10 pounds Length 25 millimeters Width 25 millimeters Material Borosilicate Glass
-
Truebore, Precision Glass Tubing
Ace GlassInside diameter tolerance of 0.0004", Trubore, a trademark of Ace Glass Incorporated, stands for precision bore tubing of the highest quality, maintained by production techniques, careful selection of raw materials, and step-by-step quality control. Trubore tubing is used in ACE items such as our…
-
Universal Solvent Jet NMR Tube Washer
SP Wilmad-LabGlassThe Universal Solvent Jet NMR Tube Washer can be used for any length NMR sample tube by a simple adjustment of the flexible PTFE tubing. By loosening and retightening the fitting on the assembled washer head, the PTFE tubing that extends into the sample tube is adjusted to the proper length.…
-
5mm O.D. Thin Walled Quartz NMR Tubes
SP Wilmad-LabGlassWilmad Precision NMR Quartz Tubes have an extremely low thermal expansion rate and high tensile strength which is 14 times more robust during the cooling/heating process than Type 1 Class A glass tubes. Naturally occurring quartz maintains an over 85% transmission rate (10 mm thickness,…
-
Adapter, Feed Tube
Ace GlassThreaded both ends and hose connection on side arm. #7 thread at top is supplied with 5029 Nylon bushing and Fetfe O-ring for use with 5831, 5832 adjustable feed tubes. Size listed is Ace-thred designation which refers to I.D. of tubing above lower thread and corresponds to 5820 column diamater.
-
10mm O.D. Medium Walled Precision NMR Tubes
SP Wilmad-LabGlassTo maximize SNR, Precision NMR Tubes have minimal paramagnetic impurities that would impact shimming. Tight ID and OD tolerance as small as 0.0065mm accommodates Wilmad inserts. Manufactured in a state-of-the-art ISO 9001:2008 USA facility using a unique precision shrinking and grinding…
-
NMR Tube for Toxic Sample, Sets and Components
SP Wilmad-LabGlassOur Double Layered Tube provides extra protection for your toxic sample. It can also be used with a reference standard which is insoluable in the sample or may cause a reaction. There is approximately a 50 µm gap between the inner and outer tubes. Ideal for variable temperature studies as…