Made of a low expansion borosilicate composition with high chemical resistance Meets all U.S. pharmacopoeia specifications for Type 1A glass 4 to 32mm O.D. sizes are 1219mm long ± approximately 6mm. 4mm O.D. have ends cut, while 5 to 32mm sizes have ends fire polished. 35 to 178mm…

Pyrex® borosilicate rod. Sold by the length. *** ALL WEIGHTS AND QUANTITIES ARE APPROXIMATE ***

Wilmad’s WG-1364 series capillary tubes are sealed at one end and provide a low cost solution for small volume NMR measurement. Made of ASTM Type 1 Class A glass Tested at 400 MHz field

Try our handy pocket NMR/EPR tube carrier; holds one 5mm O.D., 7 inch length NMR/EPR tube. Pack of 3 white holders. Features a pocket clip that keeps it secure. Made from unbreakable polymer material with a snap-on cap. Protection is provided for the sample and lab personnel during transport.

Inside diameter tolerance of 0.0004", Trubore, a trademark of Ace Glass Incorporated, stands for precision bore tubing of the highest quality, maintained by production techniques, careful selection of raw materials, and step-by-step quality control. Trubore tubing is used in ACE items such as our…

With 24/40 inner joint and 10mm hose connection. For 5mm NMR tube only. The NMR tube is inserted into the tube cleaner with its plastic cap placed on the closed end to provide support and a vacuum seal. The washing solvent is sequentially added through the side tube while a vacuum is applied…

Wilmad’s 2nd generation Multi-Tube Jet Solvent Washer/Dryer is recommended for research labs that routinely clean NMR and EPR tubes; a single unit can accommodate up to 5 tubes (3, 4 and 5 mm OD) at once. When an inverted tube is inserted onto the solvent transfer tubing and the open end is…

Manufactured from ASTM Type 1, Class A Glass, these inserts are the most versatile and reliable coaxial small volume inserts available for various NMR experiments. Upper section of each insert fits snuggly into Wilmad’s 5mm OD Thin Walled Precision NMR Tubes Stem is held straight…

Permits packing of column without excessive drop impact. Also used for side arm introduction of effluent or may be used for pressurized operation. Used in conjunction with 5029 Nylon bushing. Supplied straight or bent. Hose conn. are size C. Tube is 8 mm O.D.

Wilmad Precision NMR Quartz Tubes have an extremely low thermal expansion rate and high tensile strength which is 14 times more robust during the cooling/heating process than Type 1 Class A glass tubes. Naturally occurring quartz maintains an over 85% transmission rate (10 mm thickness,…

To maximize SNR, Precision NMR Tubes have minimal paramagnetic impurities that would impact shimming. Tight ID and OD tolerance as small as 0.0065mm accommodates Wilmad inserts. Manufactured in a state-of-the-art ISO 9001:2008 USA facility using a unique precision shrinking and grinding…

To maximize SNR, Precision NMR Tubes have minimal paramagnetic impurities that would impact shimming. Tight ID and OD tolerance as small as 0.0065mm accommodates Wilmad inserts. Manufactured in a state-of-the-art ISO 9001:2008 USA facility using a unique precision shrinking and grinding…

To maximize SNR, Precision NMR Tubes have minimal paramagnetic impurities that would impact shimming. Tight ID and OD tolerance as small as 0.0065mm accommodates Wilmad inserts. Manufactured in a state-of-the-art ISO 9001:2008 USA facility using a unique precision shrinking and grinding…

This PYREX® solvent recovery head allows for condensation and collection of solvents while performing concentrations with a Kuderna-Danish concentrator. 96-99% solvent recovery allows for concentrations to be done outside the hood. Unique, simple design allows use with existing condensers and flasks.

Wilmad Precision NMR Quartz Tubes have an extremely low thermal expansion rate and high tensile strength which is 14 times more robust during the cooling/heating process than Type 1 Class A glass tubes. Naturally occurring quartz maintains an over 85% transmission rate (10 mm thickness,…

Wilmad-LabGlass 10 mm Economy NMR Tubes are manufactured from borosilicate glass that meets the ASTM Type 1 Class B standard and recognized as N51A. Due to its nature, this glass has much less thermal-shock resistance than Class A glass used for our Precision Tubes. It may contain Fe2O3 which is…

After fitting the washer to a filter flask, an inverted sample tube is inserted into the washer and solvent is introduced into the reservoir using a series of wash bottles. You can perform numerous wash steps and finish by pulling air through the tube to complete the procedure. Filter flasks…

Threaded both ends and hose connection on side arm. #7 thread at top is supplied with 5029 Nylon bushing and Fetfe O-ring for use with 5831, 5832 adjustable feed tubes. Size listed is Ace-thred designation which refers to I.D. of tubing above lower thread and corresponds to 5820 column diamater.

14 psi rated, graduated, netted clear or plastic coated solvent reservoir bottles featuring an Omnifit, 3-valve cap. Only PTFE & Tefzel wetted surfaces. Individually controlled valves permit the application of gas under pressure for venting, flushing,

Wilmad X-Band Precision Brand EPR Quartz tubes are manufactured from naturally occurring quartz with the highest purity to minimize the background signal. Hold 10 to 15 times better tolerances on the inner diameter and 5 times smaller camber and concentricity vs economy brand tubes Ideal…

Now, sample tubes and storage vials have been joined! Save time and money with the Screw Cap EPR Tube; each come with a PTFE/Silicone Septum.

The Universal Solvent Jet NMR Tube Washer can be used for any length NMR sample tube by a simple adjustment of the flexible PTFE tubing. By loosening and retightening the fitting on the assembled washer head, the PTFE tubing that extends into the sample tube is adjusted to the proper length.…

Sample volume can be as little as 18µL 3 different inserts with various shapes (Spherical Bulb, Capillary Tube and Cylindrical Bulb) Outer tube (Precision Thin Walled) must be ordered separately depending on magnetic field strength Not recommended for variable temperature experiments…

Disposable NMR Tube Caps are manufactured from molded PVC or Polyethylene depending on the tube OD. The different colors help track samples based on various reference solvents. When using Chloroform or Acetone as reference solution, please avoid (1) direct contact between the sample and the…

Threaded both ends and with additional #7 threaded side opening for introduction of samples by hypodermic syringe. #7 thread at top is supplied with 5029 Nylon bushing and Fetfe O-ring for use with 5831, 5832 adjustable feed tubes. Size listed is Ace-thred designation which refers to I.D. of tubing…

Wilmad’s low pressure/vacuum (LPV) tube is ideal for anaerobic and gas-tight NMR experiments, and offers a convenient flame-free sealing solution for air sensitive or volatile liquid samples. Robust sealing system allows pressure build-up inside the sample Greaseless PTFE piston…

To increase success in high field NMR experiments, this tester will ensure shimming quality of your glass tubes. Useful in labs that wash, dry and reuse precision NMR tubes Warped tubes will bind in the spinner bearing while good tubes spin freely Keep a tube tester beside every NMR…

Designed to monitor reactions from start to finish, the Wilmad-LabGlass Reaction Monitoring System is a two-chamber borosilicate glass NMR tube that allows for in-tube mixing. The system features an inner chamber with a Teflon® tip that when secured creates a positive seal separating solutions…

With the steady increase of SNR on modern NMR spectrometers, the trend of small volume testing fits in high-throughput NMR to save on solvent costs. Wilmad-LabGlass presents a 3mm OD Economy Sample Tube with the same outstanding quality and performance as our legendary 5mm line. The new 4"…