Racks

Compare Tool

Select up to 3 products

1 - 32 of 87
Sort
View
Show
  • Easy tube content ID Autoclavable Angling 50 mL tubes allows easier identification of contents marked on cap. The rack, whether used on a benchtop or in a refrigerator, holds frequently used reagents nearby and on an angle facing the user. Angled rack is also useful for draining excess…

  • 28-Place Holds 28 pipets in vertical position Pipets fit into 2 discs connected by central support column Upper disc has 10 holes, 14 mm in diameter and 18 holes, 11 mm in diameter Lower disc has 28 holes, 4 mm in diameter to support pipet tips Overall height 7"; diameter 7"H …

  • This black epoxy-coated rack holds 30mm diameter or smaller centrifuge tubes in a 4 x 6 pattern, 24 tubes per rack. Height: 7.9cm (3.1"); four feet that raise the height an additional 2.1cm (0.81") Heat-cured epoxy coating is unaffected by organic solvents, salts, weak acids…

  • Excellent space-savers for use in water baths, laminar flow hoods, fume hoods or any place where space is limited. Choice of three colors: orange for biohazard warning, green and blue for general lab use. Chemical and corrosion-resistant steel wire racks are coated with heat-cured epoxy …

  • Tilt your test tube rack to 25°, 35° or 45° to reduce hand strain when working with pipettors. Also ideal for creating agar slant tubes or use with the Mini-Magnifier to aid in the viewing of Petri dishes. Base legs have predetermined slots that stand slides in and out of to…

  • Epoxy-coated steel wire rack holds 15 conical bottom 15mL centrifuge tubes. Top and middle sections have 18mm square holes and are centered over rails in the base that hold the tips of the tubes. Generously spaced for easy handling Heat-cured epoxy coating is unaffected by organic…

  • Use a Poxygrid® cone rack to support three Imhoff settling cones in a single row for clearer viewing. Lightweight Poxygrid® racks hold cone tips up off the benchtop for easier viewing and to allow plug removal if required Wire frame racks have a wide base for stability; epoxy…

  • Polypropylene racks Top and middle plates have 25 mm diameter holes; bottom plate has wells tapering from 25 to 9 mm to hold hydrometer bulb Overall height is 251 mm Steam autoclavable at 121°C 6040A10 has top plate of 143 mm high for short hydrometers

  • Slant Racks

    SP Bel-Art

    This polypropylene rack has slanted sides to help prepare agar media slants in 13-16 or 16-20mm tubes. Media-filled tubes are autoclaved with the rack in a vertical position; then the rack is positioned to the preferred angle and media allowed to cool and harden. One side is inclined 5° to create a…

  • 50mL Multiple Tube Holders Made of epoxy-coated steel wire, these racks hold up to thirty-six 50mL centrifuge tubes in holes 30mm square. Heat-cured epoxy coating is unaffected by organic solvents, salts, weak acids and weak alkalis Temperature range -223°C…

  • These racks have 12 places (3 x 4 rows) for 300mL Biological Oxygen Demand Bottles. Stackable for storage or refrigeration allowing 16.7cm (6-9/16") between racks Epoxy coated steel wire is chemical and corrosion resistant and steam autoclavable at 121°C (250°F)

  • Color Comparison Tests Just Became Easier Colors stand out against the white surfaces of this polypropylene rack making color comparison tests easier to read. Useful for drying or storing test tubes Holds six, 25mm or eight, 18mm tubes; includes six drying pins Steam…

  • Dry Test Tubes, Beakers, Flasks, and Other Labware For drying test tubes, beakers, flasks, and other labware, this stand has rubber tipped feet for non-skid use on a tabletop, or wire loops on the back for wall mounting. Three rows of epoxy-coated hairpin-loop supports (14 in all)…

  • Keeps 500mL Centrifuge Tubes Upright and Secure This unique steel wire rack allows storage and transport of up to four (4) 500mL conical bottom centrifuge tubes. Heat-cured epoxy coating is unaffected by organic solvents, salts, weak acids and weak alkalis Temperature…

  • This innovative, split-frame rack holds up to two different size tubes in the same rack and allows users to quickly switch grids to hold other sizes as needed. Each rack frame includes a set of grids in one size. Grid sets in alternate sizes can be purchased separately. 10mm to 30mm…

  • Fabricated of welded steel wire with corrosion-proof epoxy coating, this wall rack holds a single 1000mL (32oz) eye wash bottle in plain view for emergency use. Suitable for use with 8244N34 eye wash bottles (sold separately) Hangs on a screw or nail

  • Conical Tube Holder

    SP Bel-Art

    Move tube and rack with one hand, insert or remove tube from the holder with one hand. Support either a 15 or 50mL conical tube while allowing a view of the tube’s entire contents. Steam autoclavable at 121°C (250°F). Chemical-resistant polypropylene.

  • This rack is useful for safe transport and incubation of 60mm Petri dishes and helps to streamline benchtop sample processing. Rack base is epoxy coated steel, and all other parts are made of white polypropylene. Racks are shipped flat and easily assemble in minutes. Six columns hold up to…

  • Made especially for use with beakers and waterbaths, these space-saving racks are ideal for small quantities of tubes and perfect for use in microbiology and immunology labs. They are molded of buoyant TPX® brand polymethylpentene with tiny bubbles throughout for additional buoyancy. Insert…

  • Transparent acrylic stand stores 6 pipettors ready for use Stores many available pipettors Places: 6 Material: acrylic

  • Constructed of a special blend of polypropylene, these autoclavable racks will sink in a water bath Interlocking feet allow racks to be stacked while not in use Racks feature end plates for labeling. Rows are numbered and lettered for tube identification. Outside dimensions: 9.7” x…

  • Perfectly Sized for Beakers Molded of steam autoclavable polypropylene, these racks fit 400ml or 1000ml beakers. Choose from 8 or 20 place racks with 10.8mm holes for 1.5ml microtubes. Tubes remain completely immersed in a beaker while tops rest above the rack Unload by lightly…

  • Realize faster drying time by placing wet laboratory gloves on the convenient Lab-Aire® II Glove Holder. Keeps gloves open for external as well as internal drying Helps to extend glove life by maintaining their shape, preventing bending, cracking and moisture buildup Significantly…

  • Hold More Tubes, Waste Less Space This versatile polypropylene rack has pins for supporting or draining test tubes. Stores test tubes upright, full or empty Holds inverted test tubes over pins for draining The rack with 102 pins, 5 x 16 rows (9259G50), is excellent for drying…

  • Racks hold two rows of four tubes up to 20mm in diameter. Overall dimensions 108mm x 60mm x 121mm high (4 1/4 " x 2 3/8" x 4 3/4 "). Steam autoclavable at 121°C (250°F). Store and condition eight pH, Redox/ORP or ion electrodes in individual test tubes. Polypropylene rack is chemical and…

  • Organize and Safely Hold Six, 100mm Dishes The epoxy-coated steel wire Petri Dish Mini Rack helps keep benchtops neat and organized. Holds six 100mm Petri dishes with lids Ideal for lab transport and incubation of dishes Epoxy coated steel wire is chemical and corrosion resistant…

  • Organize over 100 samples in one rack Polyethylene racks provide practical methods of pipetting and storing a large number of samples Using alternate rows and rotating tubes makes it easy to keep track of the last tube filled Can be used in clinical labs for storage of samples Steam…

  • Dry It - No Matter How Much Space You Have Small, compact footprint enables placement where it is needed most Dries labware quickly by providing continous warm air circulation High storage capacity to accommodate up to 76 peg positions for all types of labware Selector knob allows…

  • Sturdy, stable polypropylene rack is made specifically for organizing and protecting 3mm O.D. thin-walled Nuclear Magnetic Resonance tubes. Holds up to 72 tubes in a 6 x 12 array. Hemispherical wells in the lower deck cradle tubes Sturdy, stable polypropylene construction Handles at…

  • Save Time and Money. No More Searching, Fumbling or Breakage. Store pipettors while protecting pipettor tips in these epoxy-coated aluminum racks that provide quick, easy access for more efficient work. Holds up to 10 round shape pipettors such as Finnpipette®, Socorex®,…

  • Specifically designed for incubating 1.5mL microcentrifuge tubes, this rack includes a hold-down disk which maintains a constant pressure on the tube caps and prevents them from opening during internal air expansion. The polypropylene disk with threaded handle screws into the…

  • Small enough to hold in one hand and enough choices to accommodate most vials and small bottles. Offered in 5 grid configurations Dimensions: 12.8 x 10.5 x 4.3cm H (5.08 x 4.15 x 1.70") Polypropylene; autoclavable

Compare Tool

Select up to 3 products