SP Bel-Art, Racks
-
Poxygrid® Labware Drain Stand
SP Bel-ArtDry Test Tubes, Beakers, Flasks, and Other Labware For drying test tubes, beakers, flasks, and other labware, this stand has rubber tipped feet for non-skid use on a tabletop, or wire loops on the back for wall mounting. Three rows of epoxy-coated hairpin-loop supports (14 in all)…
-
Scienceware® Polypropylene Pipet Racks
SP Bel-Art28-Place Holds 28 pipets in vertical position Pipets fit into 2 discs connected by central support column Upper disc has 10 holes, 14 mm in diameter and 18 holes, 11 mm in diameter Lower disc has 28 holes, 4 mm in diameter to support pipet tips Overall height 7"; diameter 7"H …
-
Poxygrid® 50mL Centrifuge Tube Racks
SP Bel-Art50mL Multiple Tube Holders Made of epoxy-coated steel wire, these racks hold up to thirty-six 50mL centrifuge tubes in holes 30mm square. Heat-cured epoxy coating is unaffected by organic solvents, salts, weak acids and weak alkalis Temperature range -223°C…
-
Scienceware® Pipet Support Rack
SP Bel-ArtHolds 12 pipets Polyethylene construction Pipet support rack supports pipets horizontally without putting pressure on fragile tips. Rack holds 12 volumetric or graduated pipets from 1 mL . The polyethylene support measures 241 mm L x 178 W x 292 H (9 1/2” x 7” x 11…
-
Microcentrifuge Floating Racks
SP Bel-ArtCompact and Economical Incubate up to twenty-four 1.5ml microcentrifuge tubes in a water bath. Easy to load Microtubes are held snugly and then released when the rack is pressed down on a benchtop Dimensions: 11.9 x 7.8cm (4-11/16 x 3-1/16")
-
Scienceware® Round Bottom Flask Support
SP Bel-ArtRound-bottom flasks of any size up to 10 liters are cradled securely in the stepped concentric rings of this holder. Can be stacked together for convenient storage Polypropylene plastic rack; not affected by spilled acids, alkalis or other corrosive liquids Steam autoclavable at…
-
Epoxy-coated steel wire rack holds 15 conical bottom 15mL centrifuge tubes. Top and middle sections have 18mm square holes and are centered over rails in the base that hold the tips of the tubes. Generously spaced for easy handling Heat-cured epoxy coating is unaffected by organic…
-
Poxygrid® "Rack and a Half" Test Tube Racks
SP Bel-ArtFor High Volume Work High quality epoxy-coated wire racks in convenient extra-long sizes for volume test tube work. Epoxy coated steel wire is chemical and corrosion resistant Steam autoclavable at 121°C (250°F)
-
Scienceware® 50mL Tube Holders
SP Bel-ArtPolystyrene construction. Leave both hands free for pipetting and other critical tasks Non-Grip Style safely supports a 50ml conical centrifuge tube and permits the tube to freely be removed Grip Style gently grips the tube and moves with the tube when it is lifted from the bench top
-
Scienceware® No-Wire™ Test Tube Racks
SP Bel-ArtGreat alternative to wire racks Stackable Available for 6 standard tube diameters Available in 3 colors Dimensions: 246mm x 104mm x 64mm high (9.7" x 4.1" x 2.5") Autoclavable at 121°C (250°F) Rugged racks are molded of autoclavable polypropylene. Footprint dimensions…
-
Autoclavable Rows are numbered and lettered Base plate has rounded wells with drain holes. Molded cutouts in end panels form handles. 9259L10 and L20 are 213 x 110 x 111 mm high; 9259L30 through L50 are 213 x 110 x 127 mm high.
-
Pipette Tray Rack
SP Bel-ArtThis styrene plastic tray can be used in drawers or on the benchtop for storing pipettes and can also be used for soaking pipettes before cleaning. Scalloped rims hold 16 small or 7 large pipettes Center support holds 12 short pipettes in a perpendicular direction
-
100mm Petri Dish Rack - Clear TPX Body
SP Bel-ArtClear, TPX® rack with polypropylene posts securely holds up to fifty-four 100mm Petri dishes. Shipped flat, they can be assembled in minutes. Easily viewed through the clear base and divider Dishes can be removed with one hand Built-in handle provides easy transport Rubber feet…
-
Poxygrid® 60 & 150-Place Test Tube Racks
SP Bel-ArtChemical and corrosion-resistant steel wire test tube rack is coated with heat-cured epoxy for long life and easy cleaning. Epoxy coatings are unaffected by organic solvents, salts, weak acids and weak alkalis Temperature range: -223°C (-369°F) to 121°C (250°F);…
-
For all of your magnetic separation experiments, these powerful racks sequester magnetic beads so that affinity ligands (antibodies, streptavidin or proprietary reagents for coupling nucleic acids) or rinse solutions can be added or decanted in assays. They offer exceptional quality and value…
-
Poxygrid® 50mL Centrifuge Tube Racks
SP Bel-ArtThis black epoxy-coated rack holds 30mm diameter or smaller centrifuge tubes in a 4 x 6 pattern, 24 tubes per rack. Height: 7.9cm (3.1"); four feet that raise the height an additional 2.1cm (0.81") Heat-cured epoxy coating is unaffected by organic solvents, salts, weak acids…
-
Scienceware® Poxygrid® B.O.D. Bottle Rack
SP Bel-ArtThese racks have 12 places (3 x 4 rows) for 300mL Biological Oxygen Demand Bottles. Stackable for storage or refrigeration allowing 16.7cm (6-9/16") between racks Epoxy coated steel wire is chemical and corrosion resistant and steam autoclavable at 121°C (250°F)
-
Color Comparison Tube Rack
SP Bel-ArtColor Comparison Tests Just Became Easier Colors stand out against the white surfaces of this polypropylene rack making color comparison tests easier to read. Useful for drying or storing test tubes Holds six, 25mm or eight, 18mm tubes; includes six drying pins Steam…
-
Scienceware® No-Wire™ Round Racks
SP Bel-ArtThese No-Wire™ racks fit neatly into round containers such as ice buckets and beakers, as well as desiccators. Choose from two sizes; the large rack is ideal for use in round ice buckets such as Magic Touch™ and the small rack fits perfectly in a 1000mL beaker. Special…
-
Scienceware® Rack, PP, Electrode
SP Bel-ArtRacks hold two rows of four tubes up to 20mm in diameter. Overall dimensions 108mm x 60mm x 121mm high (4 1/4 " x 2 3/8" x 4 3/4 "). Steam autoclavable at 121°C (250°F). Store and condition eight pH, Redox/ORP or ion electrodes in individual test tubes. Polypropylene rack is chemical and…
-
Poxygrid® "Half-Size" Test Tube Racks
SP Bel-ArtExcellent space-savers for use in water baths, laminar flow hoods, fume hoods or any place where space is limited. Choice of three colors: orange for biohazard warning, green and blue for general lab use. Chemical and corrosion-resistant steel wire racks are coated with heat-cured epoxy …
-
Scienceware® Stack Rack® Test Tube Racks
SP Bel-ArtMatch Rack Material to Lab Use These sturdy, rigid racks feature interlocking end plates with handles for secure stacking when loaded with tubes up to 10cm (4") long. Rows are numbered and lettered for easy tube identification. All racks are steam autoclavable at 121°C (250°F). …
-
Stainless Steel Pipettor Stand
SP Bel-ArtMade of stainless steel without any plastic coating, this universal rack holds all types of pipettors including the Gilson Pipetman®. Five positions, sloping back and open front notches hold the pipettors Suitable for free standing on a bench top
-
24-Hole Scintillation Vial Rack Takes 24 vials up to 30 mm o.d. Autoclavable; non-scratching Molded cutouts in end panels form handles For start to finish preparation Height to top of upper shelf: 44 mm. Overall dimensions: 298 x 127 x 95 mm high. Height to top of upper shelf is 1-3/4".
-
Microcentrifuge Tube Rack
SP Bel-ArtSteam autoclavable at 121°C (250°F). Dimensions: 210mm x 70mm x 35mm H (8 ¼" x 2 ¾" x 1 3/8"). Two-level polypropylene rack organized and stores twenty 1.5ml tubes in numbered wells. Tubes protrude 25mm (1") for easy removal.
-
Rotary Separatory Funnel Rack
SP Bel-ArtThis rotary separatory funnel rack consists of a rectangular base, screw-in column and a support disc held in place by a screw clamp. Support disc is fully adjustable for different heights up to 21" Open front type support holes for easy removal and placement of separatory funnels …
-
Scienceware® No-Wire™ Cuvette Rack
SP Bel-ArtAll-polypropylene rack provides gentle no-scratch support for fragile and expensive spectrophotometer cuvettes. Holds forty-two 10mm light path cuvettes 6 x 7 row layout Steam autoclavable at 121°C (250°F)
-
Scienceware® 250mL Centrifuge Bottle Rack
SP Bel-ArtEpoxy-coated steel wire, holds six bottles in 60 mm square grids on two levels Bottom level has rails to hold the tip of the conical bottom of the bottles Dimensions are 8-3/8” x 5-1/2” x 4” (20.8 x 13.5 x 10.2 cm H) Perfect for conical and round bottom bottles that can't stand…
-
Switch-Grid™ Test Tube Racks
SP Bel-ArtThis innovative, split-frame rack holds up to two different size tubes in the same rack and allows users to quickly switch grids to hold other sizes as needed. Each rack frame includes a set of grids in one size. Grid sets in alternate sizes can be purchased separately. 10mm to 30mm…
-
Spectro Cell Rack
SP Bel-ArtWells hold standard cells with a 12.5mm cross-section; however, some plastic cells may not fit. Steam autoclavable at 121º C (250º F). Overall dimensions 209 x 70 x 35mm (8 1/4" x 2 3/4" x 1 3/8 "). Polypropylene rack holds twenty 10mm lightpath Spectrophotometer cells in numbered wells The…