Labconco, Hoods, Supplies
-
Protector Work Station Accessories
LabconcoFilters for Labconco protector work stations Impregnated charcoal filter packs remove dangerous vapors from the work area 5165N47 1 3/8” filters slip behind stainless steel grill to remove formaldehyde vapors quickly and completely
-
Carbon-based and HEPA filters used in a variety of Labconco enclosures require periodic replacement. Applicable products include: PuriCare Procedure Stations (pre-2008), Purifier Cell Logic Biosafety Cabinets and Purifier Logic Biosafety Cabinets with an enclosure nominal width of 6 feet.
-
Filtermate Portable Exhausters
LabconcoCompact, corrosion-resistant housing Inherently safe design An accessory for the Demonstration Hood, XPert Balance Enclosure, Protector® XVS Ventilation Station or Protector® Work Station, the FilterMate uses a HEPA filter, carbon-based filter or a combination of both filters…
-
Applicable Products: Basic Laboratory Hoods For installation in a factory-prepared cutout on the upper portion of the Basic Hood's right side fixture panel. Guardian 500 Airflow Monitor senses and alerts the operator to low airflow conditions. Includes a face plate with circuit…
-
The Purifier Axiom Class II, Type C1 is the first biological safety cabinet that can be used in a recirculating Type A-mode for standard microbiological work, or can be connected to an exhaust system to function in Type-B mode for handling hazardous chemical vapors or radionuclides. Because of the…
-
SpillStopper Work Surfaces are compatible with Protector (Premier or XStream) Laboratory Hoods with Eco-Foil(TM) Air Foil. Molded from a special formulation of corrosion-resistant epoxy resins, these work surfaces are dished and contoured to conform to the interior liner of Protector Laboratory…
-
Protector PVC Perchloric Acid Laboratory Hood. 37.7" deep. Features heat-welded unplasticized PVC liner, built-in washdown system, integral work surface, drainage trough and 3/16" thick tempered safety glass vertical-rising sash with frame of powder-coated aluminum and PVC (glass is suitable for…
-
Protector Pass-Through Laboratory Hoods offer sashes on two sides allowing operation on either side of the fume hood. An audible alarm sounds to prevent simultaneous opening of both sashes. With unobstructed visibility from either side, this hood is ideal for conducting chemistry demonstrations. …
-
The Purifier Axiom Class II, Type C1 is the first biological safety cabinet that can be used in a recirculating Type A-mode for standard microbiological work, or can be connected to an exhaust system to function in Type-B mode for handling hazardous chemical vapors or radionuclides. Because of the…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Protector standard storage cabinet features 18 gauge steel exterior sidewalls that are epoxy-coated for chemical resistance. Cabinets feature two non-locking manual doors. Four individual leveling feet allow users to make adjustments to level the cabinet based on the condition of their floors.…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Sash stop kit
LabconcoSash Stop Kit. Restricts how far a vertical-rising sash may be opened. Compatible with Protector Xstream and Premier Fume Hoods
-
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Protector Filtered Fume Hoods
LabconcoNeutrodine Unisorb Molecular Filter Neutrodine Unisorb molecular carbon filter unit for multi-purpose use of acids/bases/solvents, separated or combined. Compatible with 500+ chemicals. For use with Protector Echo and Airo Filtered Hoods. 1 EA. HEPA Filter, 99.995% efficient, H14 type, for…
-
XPert Balance Enclosure Stations
LabconcoXPert Filtered Balance Stations are designed to protect the user during powder weighing operations. Ducting to an outside blower is required. Patented features include an ergonomic air foil with Clean-Sweep openings to enhance airflow and a zone-perforated rear baffle that creates horizontal…
-
Conversion Kit for 4'-8' Protector XL Floor-Mounted Fume Hood ceiling enclosure kit (sold separately). 3-Sided Ceiling Enclosure Kits include 3 glacier white powder-coated steel panels (front & 2 sides) that extend from top of hood to ceiling to hide ductwork, plumbing & wiring. 1EA.
-
Handle extremely corrosive atmospheres produced by high order oxidizers such as perchloric acid Intelli-Sense Multi-Speed Blowers are weatherized, direct drive, non-explosion-proof blowers controlled by a two or three position switch. Each blower has a reliable electronically commutated…
-
Protector Airo Filtered Fume Hoods
LabconcoThe Protector® Airo™ Filtered Fume Hood has a compact design that avoids potential challenges of existing lab conditions while still providing space, utility and options of a traditional hood. It features all of the characteristics of Labconco Protector Hoods including the patented…
-
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
Protector Filtermate
LabconcoRequire no outside ducting Non-sparking motor/blower Foot operated on/off switch Durable construction Hard rubber casters Adjustable blower speed An accessory to the Protector® VS™ Ventilation Station, the Filtermate filters the contaminated air generated and returns purified air to the…
-
Guardian™ 500 Airflow Monitors
LabconcoMonitor and alert the operator to low airflow conditions. Mount atop Protector XVS Ventilation Stations, Protector Demonstration Hoods and Protector Work Stations in factory prepared location. Include face plate with circuit board, electrical power pack, tubing, airflow tube adapter and…
-
Fiberglass 30 Laboratory Hoods
LabconcoCompact, benchtop Fiberglass 30 Laboratory Hoods are designed for research, educational and clinical applications requiring small working space and efficient fume removal. The fiberglass liner is corrosion-resistant, durable, fire-resistant and light reflective. The smooth one-piece molded…
-
gGuard® Communication Software Automatically collects and records hood data, alerts and alarms on a customer-supplied personal computer Monitors, manages and provides data via email to a designated facility manager Provides access to the following: usage authorization, filter…
-
Molded of corrosion-resistant epoxy resins, dished & contoured to conform to interior of ClassMate Hoods. Pre-drilled 1.5" dia holes for venting & 2.5" dia holes for plumbing.
-
Protector XL Floor-Mounted (Walk-In) Laboratory Hoods have panel liners that may be constructed of a variety of corrosion-resistant materials and supplied in three depths to meet individual installation and application requirements. They are suitable for general chemistry applications and…
-
The Protector XStream I-S Laboratory Hood was engineered to be the best containing fume hood possible. Testing shows the Protector XStream I-S easily meets containment per SEFA-1 low velocity hood standards when subjected to the ASHRAE 110 test protocol with results of less than 0.05 ppm leak rate…
-
-
Protector Fume Hood Accessories
LabconcoScreen mounts behind the baffles for trapping tissue wipers & other papers. Each kit includes mounting hardware, powder-coated stainless steel screen & instructions. Contact Labconco for screens for hoods wider than 8'.
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…