Labconco, Hoods
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Protector PVC Acid Digestion Laboratory Hood. 37.7" deep. Features heat-welded unplasticized PVC liner, built-in washdown system, integral work surface, drainage trough and 3-16" thick tempered safety glass vertical-rising sash with frame of powder-coated aluminum and PVC (glass is suitable for…
-
Applicable Products: Basic Laboratory Hoods For installation in a factory-prepared cutout on the upper portion of the Basic Hood's right side fixture panel. Guardian 500 Airflow Monitor senses and alerts the operator to low airflow conditions. Includes a face plate with circuit…
-
The Protector XL Benchtop Laboratory Hoods offer superior design flexibility. Their panel liners are supplied in three depths to meet individual installation and application requirements. Protector XL Benchtop Laboratory Hoods are suitable for general chemistry applications. Features …
-
Protector Premier I-S Laboratory Hoods incorporate a sleek interior with a molded one-piece fiberglass liner, the signature feature of Labconco’s leading line of fume hoods since 1961. The one-piece liner of specially-formulated, fiberglass-reinforced polyester offers corrosion and fire…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
SpillStopper™ Work Surfaces, 8' Wide
LabconcoSpillStopper Work Surfaces are molded from a special formulation of corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled…
-
Protector Pass-Through Laboratory Hoods offer sashes on two sides allowing operation on either side of the fume hood. An audible alarm sounds to prevent simultaneous opening of both sashes. With unobstructed visibility from either side, this hood is ideal for conducting chemistry demonstrations. …
-
Electrical Receptacle Kit for mounting to the left or right side of a 3', 4', 5', 6', 7' or 8' Protector Premier, Xstream, XL, PVC Perchloric Acid or Stainless Steel Laboratory Hood. Includes electrical receptacle, wiring, junction box and receptacle cover plate. …
-
PVC T & Y Connections
LabconcoPVC fitting compatible with thermoplastic duct. End connections receive PVC pipe directly. 0516E96 - PVC "T" Connection: Duct Diameter: 10" Duct Diameter: 12" Duct Connection Diameters: 10" x 10" x 12" Height: 19" Equivalent Resistance in feet of Straight Duct: 20' …
-
XPert Filtered Balance Systems provide user protection by keeping powders and particulates contained during weighing procedures. Patented features include an ergonomic air foil with Clean-Sweep openings to enhance airflow and a zone-perforated rear baffle that creates horizontal laminar airflow to…
-
Fiberglass 30 Laboratory Hoods
LabconcoCompact, benchtop Fiberglass 30 Laboratory Hoods are designed for research, educational and clinical applications requiring small working space and efficient fume removal. The fiberglass liner is corrosion-resistant, durable, fire-resistant and light reflective. The smooth one-piece molded…
-
SpillStopper Work Surface molded of corrosion-resistant solid epoxy. Dished & contoured to conform to interior liner of Protector Pass-Through Hoods. Pre-drilled 2.5" (6.4cm) dia plumbing holes.
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
SpillStopper™ Work Surfaces, 6' Wide
LabconcoSpillStopper Work Surfaces are molded from a special formulation of corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Spiral Tube
LabconcoCorrosion-resistant, neoprene-impregnated fiberglass reinforced with steel wire. Include rigid duct connector and two clamps. Because this ductwork is flexible and may conform to various configurations, it is not possible to know the precise equivalent resistance.
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Guardian Digital Airflow Monitors
LabconcoGuardian™ Digital Airflow Monitor senses and alerts the operator to low airflow conditions. LCD displays actual airflow in fpm or m/sec. Audible/visual alarm alerts the user to sustained low velocity condition. Calibration instructions displayed on LCD. Each monitor also includes a…
-
Protector Work Station Accessories
LabconcoFilters for Labconco protector work stations Impregnated charcoal filter packs remove dangerous vapors from the work area 5165N47 1 3/8” filters slip behind stainless steel grill to remove formaldehyde vapors quickly and completely
-
The Purifier Axiom Class II, Type C1 is the first biological safety cabinet that can be used in a recirculating Type A-mode for standard microbiological work, or can be connected to an exhaust system to function in Type-B mode for handling hazardous chemical vapors or radionuclides. Because of the…
-
The Purifier Axiom Class II, Type C1 is the first biological safety cabinet that can be used in a recirculating Type A-mode for standard microbiological work, or can be connected to an exhaust system to function in Type-B mode for handling hazardous chemical vapors or radionuclides. Because of the…
-
Protector® Premier® Laboratory Hoods
LabconcoProtector® Premier® Laboratory Hoods incorporate a sleek interior with a molded one-piece fiberglass liner, the signature feature of Labconco’s leading line of fume hoods since 1961. The one-piece liner of specially-formulated, fiberglass-reinforced polyester offers corrosion and fire resistance…
-
Guardian™ Airflow Monitors
LabconcoGuardian™ Airflow Monitor senses and alerts the operator to low airflow conditions. From the monitor's face plate, the user can easily select and calibrate a set point between 30 and 250 fpm using a velocity meter and a screwdriver. Audible/visual alarm. Includes night setback, external alarm and…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
Handle extremely corrosive atmospheres produced by high order oxidizers such as perchloric acid Intelli-Sense Multi-Speed Blowers are weatherized, direct drive, non-explosion-proof blowers controlled by a two or three position switch. Each blower has a reliable electronically commutated…
-
Monitor features an LCD that displays average face velocity. Audible/visual alarm alerts user to low or high face velocity. Kit is for installation in a factory-prepared cutout on the upper portion of the right side fixture panel. Kits are available for use with 115V, 60 Hz operation or 230V,…
-
Filtermate Portable Exhausters
LabconcoCompact, corrosion-resistant housing Inherently safe design An accessory for the Demonstration Hood, XPert Balance Enclosure, Protector® XVS Ventilation Station or Protector® Work Station, the FilterMate uses a HEPA filter, carbon-based filter or a combination of both filters…
-
Guardian™ 500 Airflow Monitors
LabconcoMonitor and alert the operator to low airflow conditions. Mount atop Protector XVS Ventilation Stations, Protector Demonstration Hoods and Protector Work Stations in factory prepared location. Include face plate with circuit board, electrical power pack, tubing, airflow tube adapter and…