Hoods

Compare Tool

Select up to 3 products

1 - 32 of 116
Sort
View
Show
  • Fume Hood Exhaust Blowers

    Hemco

    Epoxy coated steel, belt drive, exhaust blowers for canopy hoods based on duct runs under 25ft and no more than 4 elbows. These exhaust blowers are designed to maintain between 80 to 100FPM.

  • Protector XStream I-S Laboratory Fume Hoods

    Labconco

    The Protector XStream I-S Laboratory Hood was engineered to be the best containing fume hood possible. Testing shows the Protector XStream I-S easily meets containment per SEFA-1 low velocity hood standards when subjected to the ASHRAE 110 test protocol with results of less than 0.05 ppm leak rate…

  • Side & Bottom Lab-Frame Kits for Fume Hoods

    Lee Engineering

    4' Frame Measures: 36" x 38" 6' Frame Measures: 36" x 62" 8' Frame Measures: 36" x 86" Chamfered Ends Rods are corrosion-resistant

  • Protector® Airo™ Filtered Fume Hoods

    Labconco

    If you have robust chemical applications requiring a fume hood but have low ceiling height and no means to duct to the outside, consider the Protector® Airo™ Filtered Fume Hood. Labconco has combined its patented* fully-featured, containment- enhancing Protector® Hood design with…

  • Epoxy Resin Work Surfaces

    Hemco

    Epoxy Resin Worksurfaces are recommended for general laboratory work where greater chemical resistance is required. Surface is dished 3/8" to contain spillage. Worksurface is cast of thermosetting epoxy resin, creating a molded solid 1-1/4" thick top which is extremely hard, abrasion and…

  • Fiberglass 30 Laboratory Hoods

    Labconco

    Compact, benchtop Fiberglass 30 Laboratory Hoods are designed for research, educational and clinical applications requiring small working space and efficient fume removal. The fiberglass liner is corrosion-resistant, durable, fire-resistant and light reflective. The smooth one-piece molded…

  • Protector Premier I-S Laboratory Fume Hoods

    Labconco

    Protector Premier I-S Laboratory Hoods incorporate a sleek interior with a molded one-piece fiberglass liner, the signature feature of Labconco’s leading line of fume hoods since 1961. The one-piece liner of specially-formulated, fiberglass-reinforced polyester offers corrosion and fire…

  • SpillStopper Work Surfaces, for Protector Premier Hoods

    Labconco

    SpillStopper Work Surfaces are compatible with Protector (Premier or XStream) Laboratory Hoods with Eco-Foil(TM) Air Foil. Molded from a special formulation of corrosion-resistant epoxy resins, these work surfaces are dished and contoured to conform to the interior liner of Protector Laboratory…

  • 8' Protector Echo Filtered Fume Hoods

    Labconco

    Protector Echo Filtered Fume Hoods with Neutrodine filtration are appropriate for procedures that require personnel protection in a lab that cannot accomodate duct work nor make-up air. Labconco has combined its patented fully-featured, containment-enhancing Protector® Hood design…

  • Phenolic Work Surfaces

    Hemco

    Flat phenolic work surface for Universal and Clean Aire II hoods.

  • UniFlow LE AireStream Laboratory Fume Hoods

    Hemco

    UniFlow LE Airestream fume hoods are a high-efficiency, full duty, low flow constant volume for energy savings & maximum user protection. The aerodynamic face opening with airfoil provides uniform air flow through the fume chamber. The Vector baffle system directs the air through the fume…

  • Zero Pressure Weathercaps

    Labconco

    Made of strong, corrosion-resistant PVC. Caps fit atop standard PVC duct, permits vertical discharge of effluent air above roofline for dispersion away from the building. Caps add little static pressure to the exhaust system.

  • Carbon Filter Packs

    Labconco

    Carbon Filter Pack. Activated Carbon Filter for non-radioactive organic vapors and odor control. Rated for 1000 CFM air flow with 0.2" static pressure drop. Dimensions: 28" W x 28" L x 25" H.

  • Guardian™ Airflow Monitors

    Labconco

    Guardian™ Airflow Monitor senses and alerts the operator to low airflow conditions. From the monitor's face plate, the user can easily select and calibrate a set point between 30 and 250 fpm using a velocity meter and a screwdriver. Audible/visual alarm. Includes night setback, external alarm and…

  • 6' Protector Pass-Through Laboratory Hoods

    Labconco

    Protector Pass-Through Laboratory Hoods offer sashes on two sides allowing operation on either side of the fume hood. An audible alarm sounds to prevent simultaneous opening of both sashes. With unobstructed visibility from either side, this hood is ideal for conducting chemistry demonstrations. …

  • Protector Work Stations

    Labconco

    Face velocities from 60 to 100 fpm Built-in dynamically-balanced motorized impeller Speed controlled to achieve desired inflow velocity Protector Work Stations are specifically designed for the needs of pathologists and histotechnologists. Like a traditional fume hood, these enclosures have a…

  • Stainless Steel Island Canopy Hoods

    Hemco

    Canopy hoods are designed to collect and exhaust corrosive vapors, heat, steam, and odors when mounted over areas with water baths, hot plates, or portable equipment. Made of type 304 Stainless Steel, the Canopy Fume Hood’s glass smooth surfaces provide superior chemical, corrosion and heat…

  • SpillStopper Work Surfaces, for Protector XStream Hood

    Labconco

    SpillStopper Work Surfaces are compatible with Protector (Premier or XStream) Laboratory Hoods with Eco-Foil(TM) Air Foil. Molded from a special formulation of corrosion-resistant epoxy resins, these work surfaces are dished and contoured to conform to the interior liner of Protector Laboratory…

  • Flexible Exhaust Duct, 42" length

    Labconco

    42" length of 2" diameter steel-reinforced vinyl duct with two clamps.

  • Epoxy Work Surface w/Sink

    Labconco

  • MicroFlow II Filtered Workstation

    Hemco

    The MicroFlow II Workstation is ideal for: A Class 1 ductless hood workstation. Activated Carbon Filtration for fumes, odors, and non-hazardous chemical vapors, pre-filter for particulate Completely self contained with clear hood surround with safety viewing sash for user Clear hood…

  • 4' Protector Pass-Through Laboratory Hoods

    Labconco

    Protector Pass-Through Laboratory Hoods offer sashes on two sides allowing operation on either side of the fume hood. An audible alarm sounds to prevent simultaneous opening of both sashes. With unobstructed visibility from either side, this hood is ideal for conducting chemistry demonstrations. …

  • Guardian 500 Airflow Monitors (for Basic Laboratory Hoods)

    Labconco

    Applicable Products: Basic Laboratory Hoods For installation in a factory-prepared cutout on the upper portion of the Basic Hood's right side fixture panel. Guardian 500 Airflow Monitor senses and alerts the operator to low airflow conditions. Includes a face plate with circuit…

  • Sciencware® Tapered Rear Exhaust Fume Hoods

    Bel-Art - SP Scienceware

    Ideal Vent for Tanks and Vats These polypropylene exhaust hoods are intended to rest on the rear edge of a tank and draw a stream of air across the top of the tank, away from the operator. An exhaust system is required. Formula for calculating required airflow for hood: 1.833 x 150 = 274.95…

  • Thermoplastic Duct Reducers

    Labconco

    PVC coupling type reducer designed for connecting thermoplastic duct of different diameters with no equivalent resistance.

  • SpillStopper™ Work Surfaces, 8' Wide

    Labconco

    SpillStopper Work Surfaces are molded from a special formulation of corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled…

  • HEPA Exhaust Filter For Cabinet 6' Purifier Logic II Cabinets And 6' Puricare

    Labconco

    Carbon-based and HEPA filters used in a variety of Labconco enclosures require periodic replacement. Applicable products include: PuriCare Procedure Stations (pre-2008), Purifier Cell Logic Biosafety Cabinets and Purifier Logic Biosafety Cabinets with an enclosure nominal width of 6 feet.

  • Table Top Mount Lab-Frame Kits for Fume Hoods

    Lee Engineering

    Frame Measures: 36" x 38" x 9" Chamfered Ends Rods are corrosion-resistant

  • Guardian Digital Airflow Monitor Kits

    Labconco

    Monitor features an LCD that displays average face velocity. Audible/visual alarm alerts user to low or high face velocity. Kit is for installation in a factory-prepared cutout on the upper portion of the right side fixture panel. Kits are available for use with 115V, 60 Hz operation or 230V,…

  • MicroFlow I Ductless Workstation

    Hemco

    The MicroFlow I Workstation is ideal for: A Class 1 ductless hood workstation. Activated Carbon Filtration for fumes, odors, and non-hazardous chemical vapors, pre-filter for particulate. Completely self contained with clear hood surround with safety viewing sash for user Integral work…

  • Protector PVC Perchloric Acid Laboratory Hoods

    Labconco

    Protector PVC Perchloric Acid Laboratory Hood. 37.7" deep. Features heat-welded unplasticized PVC liner, built-in washdown system, integral work surface, drainage trough and 3/16" thick tempered safety glass vertical-rising sash with frame of powder-coated aluminum and PVC (glass is suitable for…

  • Organic Filter Cell

    Labconco

    Organic Carbon Filter, Type AC. Contains 12 pounds of granular activated carbon media suitable for organic solvents including acetone, ethyl acetate, toluene and xylene. Carbon-based filters used in a variety of Labconco enclosures require periodic replacement.

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.