This closed system tissue homogenizer (tube with pestle) is non-sterile and packaged in a bulk pack configuration.

This column features all borosilicate glass construction with an 85 mL reservoir The glass wool plug and PTFE tubing at the bottom of the column are held securely in place by a BEVEL-SEAL™ connection, facilitating easy cleaning and assembly PTFE BEVEL-SEAL™ stopcock connector is…

For use in many refluxing operations, including Soxhlet extractions. Straight outlet tube at top Water-cooled Standard Taper inner drip joint at bottom Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

With Standard Taper Joints Complete with Allihn condenser with joint at bottom, Soxhlet extraction tube with top and bottom joint and flat-bottom flask Available in small, medium and large capacities Small Extractor with 125 mL flask (4406E10, E16, E22) Extraction chamber 30 mm i.d. x 95…

The KONTES® DISPOSAFLEX® column is an inexpensive, multi-purpose column designed to satisfy a wide range of analytical separations using aqueous buffers. A typical application of the Disposaflex® column is the extraction of the cyclic nucleotides cAMP and cGMP from sample preparations…

For ASTM D 97, D 2500 Cylindrical with flat bottom, beaded rim and marking spot Height 125 mm; o.d. 35 mm With graduation ring 54 mm from bottom

Choice of coarse or extra coarse porosity cylinder Gas dispersion tube has a hollow fritted cylinder at the end of the tube. Cylinder height x o.d.: 24 x 13 mm. stem diameter: 8 mm. Overall height: 250 mm

Solvent bottle adapter Economy three-hole cap Inlet/sparge filter Safety system 3 combines a three-hole cap, solvent bottle adapter and a combination inlet/sparge filter to eliminate the safety hazards of aluminum foil wrapped solvent containers. Solvent bottle adapter converts GL-45…

Angled two neck round bottom flask. Two-neck heavy wall flask with 24/40 Standard Taper outer joints Side neck is angled Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

This apparatus combines two analytical techniques, Soxhlet extraction and Dean-Stark azeotropic distillation, into a single process for the removal of water, chlorinated dibenzo-p-dioxins (CCDs) and chlorinated dibenzofurans (CDFs) from wet particulate samples. Determination of water and…

Friedrich Condenser with hose connection sidearm. 45/50 bottom standard taper joint Ring-sealed inner condensing tube with inner drip joint and side outlet for drying tube Molded 190 mm inner cold finger Used primarily in reflux mode and Soxhlet extractions Fits tubing ID 3/8"

For connecting inert gas and vacuum sources Stopcock has metering groove cut into the plug to provide fine control of vacuum and inert gases. Distance between stopcocks is 65 mm for 8651N01 and 100 mm for 8651N03. Include patented pressure/vacuum retainers. Dimensions (mm): 8651N01: 230 L x…

Standard Taper outer joint at the top Standard Taper inner drip joint at the bottom Hose connections accept 3/8” ID flexible tubing Ref: ASTM Method D322 Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

Columns are supplied complete with glass barrel, 2 end fittings with 20 μm porosity HDPE bed supports, and screw caps Each column is also supplied with 5 feet (1.5 m) of FEP PTFE tubing (1/16” OD with 1.0 cm; 1/8” OD with 2.5 and 4.8 cm), 2 flangeless tubing nuts and 2 flangeless…

Columns are supplied complete with glass barrel, 2 end fittings with 20 μm porosity HDPE bed supports, and screw caps Each column is also supplied with 5 feet (1.5 m) of FEP PTFE tubing (1/16” OD with 1.0 cm; 1/8” OD with 2.5 and 4.8 cm), 2 flangeless tubing nuts and 2 flangeless…

Flow adapters Flow adapters can significantly improve FLEX-COLUMN® performance by protecting the gel bed from disruption during sample loading and by eliminating any dead volume above the gel bed.  Ideal for concentration and pH gradients, reverse flow separations and gravity…

Snyder distillation column with floating ball valves for improved vapor-liquid contact. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements.

The reinforced top and tooled lower end of this KIMAX® column provide extra strength and a tight, leakproof fit with an all-PTFE stopcock. An o-ring has been added under the PTFE fitment to maintain a liquid-tight seal over a large temperature range (0-100 °C) Liquid contacts…

For gravimetric oil and grease Three position linear system Heating mantle, controller and splash guard are required for complete system (clamps and support included): power 15 amps - 115 volts. Refrigerating circulator recommended for system water coolant: -4°C. Proper ventilation…

The narrow annular space of the West design provides high cooling efficiency due to the increased flow rate of the cooling medium. Full length 24/40 joints Standard Taper outer joint at the top and Standard Taper inner drip joint at the bottom Manufactured from 33 expansion, low…

Gravity chromatography column manufactured from medium wall tubing with 821000 PTFE stopcock Similar in design to the 420530 series 40-60 micron porosity glass frit at the lower end to act as a support for column packing material Replacement stopcock plug is 821001 Manufactured from 33…

This three-position linear solvent recovery system is intended for use with Kuderna Danish evaporative concentrators. Heating mantle, controller, splash guard, clamps and supports provided with the complete system Power: 15 amps – 120 volts Refrigerating circulator recommended…

Made of autoclavable CTFE/Stainless Steel Optional cordless drive unit available, see Thomas number 3411E25.

Gravity chromatography column manufactured from medium wall tubing with PTFE stopcock and in-line reservoir for containing liquid buffer Standard Taper joint size 24/40 These gravity columns may be used alone or in combination with 420575-2440 flow control adapter A coarse porosity glass…

All-glass construction with ground tube Ideal for connective tissues Clearance between pestles and tubes is .004 to .006 inches* Pestle can be motor driven (see Thomas number 3411E25 for Drive Unit) Available in working capacities of 1, 5, 8, 17 and 45 mL . * Stated clearances…

Tightly wound coil provides enough surface area to condense high vapor pressure solvents like hexane. With an internal, coil-type cold finger Standard Taper outer joint at the top, Standard Taper inner drip joint at the bottom 283000 does not have a drip joint Two hose connectors…

Developed in the laboratories of Julius Hyman and Company for the concentration of trace amounts of sample dissolved in organic solvents. It is very useful in sample preparation before analysis with solvents such as petroleum ether or hexane. Preparation involves filling the flask to between…

Jacketed CHROMAFLEX® columns are provided with an acrylic water jacket to provide thermal control of temperature-sensitive chromatographic separations.  The acrylic jacket also acts as a safety shield.  Threaded Recommended sterilization is with ethylene oxide, 2N NaOH or…

FLEX-COLUMNS® are economical and easy-to-use. Short columns are typically used for ion exchange chromatography, sample desalting and semi-disposable applications, while the long columns are ideally suited for gel filtration and adsorption chromatography. Constructed of polypropylene…

KIMAX® desiccators are designed and made for durability and efficiency in daily laboratory use. Ideal for removing moisture from solids, storing hygroscopic materials, and applications requiring vacuum desiccation. Can also be used for cooling oven-dried samples while maintaining sample…

Ideal for use with gel filtration, ion exchange, affinity and adsorption media Economical Easy to use Universal fittings and tubing connections Ideal for use with gel filtration, ion exchange, affinity and adsorption media. Polypropylene reservoirs and column outlets are permanently…

Similar to 3432N01 series, but with PTFE pestle and an unground glass tube Ideal for soft tissue such as brain or liver Clearance between pestles and tubes is .004 to .006 inches* Pestle can be motor driven (see Thomas number 3411E25 for Drive Unit). Available in working…