Ace Glass, Equipment
-
Replacement condenser for Buchi rotary evaporators. Available plain or safety coated. Includes PTFE hose barbs,GL caps and plug.
-
Condenser, Spiral
Ace GlassWith spiral condensing tube having both inlet and outlet connections at top, on same side. With standard taper joints. Length between joints is approximately 80-90 mm longer than the stated coil length.
-
Support Stand, Kilo Scale Reactors
Ace GlassThomas No. 1165L75, 1165L76, 1165L77, 1165L78, 1165L79, 1165L80 Redesigned, modular Kilo scale reactor support stand Thomas No. 1165L81 Bracing set to further strengthen the Universal Stand²against the weight of our explosion proof motor. Set²consists of two braces. …
-
Condenser, Friedrichs
Ace GlassReflux controlled by regulating jacket temperature. Provides compact spiral path for condensation. Jacket length 200mm. Bottom standard taper 24/40 joint.
-
Plain, open top, chromatographic column, with porosity B (70 - 100 m) fritted disc sealed in.
-
Condenser, Jacketed Reflux, Threaded
Ace GlassMicroscale, water-jacketed condenser used in reflux experiments. With outer joint at top externally threaded to allow an O-RING-CAP-SEAL connection with mating male joints and inner joint at bottom, with drip tip. I.D. of inner tube on code -23 is sufficiently large enough to accept regular size…
-
Clamp, Two-Piece, Flat Flange
Ace GlassTwo-piece unfinished aluminum clamp with PTFE gaskets and brass tightening bolts. Code -03 fits our 7646-18 75mm o-ring joint and our 7519 (76mm) filter support assembly. Code -05 fits our 7519 (102mm) filter support assembly and our 6504 kettles with
-
Fully flexible drive shaft facilitates isolation of the stirrer motor from the reactor. Complete units, code -30 (91.4cm) and code -32 (152.4cm), designed for use with 8mm (5/16in) motor shaft. Purchase the optional code -27 adapter for motors with 9.5mm (3/8in) shafts. Reactor end consists of a…
-
Bulb type for use with regular extraction apparatus. Improved design permits greater condensing capacity. Jacket lengths approximately 255mm with one bulb per 50mm.
-
Cold Finger Condenser
Ace GlassCold Finger accessory for standard distilling heads and systems. This cold finger has an inner joint that fits inside the upper outer joint and tube to provide added cooling ability and faster condensation. Fits into 6606, 6609, and 6613 distillation h
-
Bearing, Trubore, Economy, 6mm
Ace GlassTrubore bearing, heavy duty, standard taper joint, self-aligning. Unique design is forgiving of slight misalignment of stir motor and shaft. Recommended for use with our 9534 6mm precision ground stir shaft.
-
Chromatographic column with integral reservoir for connecting 5872 Flow Control Adapter. With 2mm bore, 1:5 taper solid PTFE stopcock plug at bottom. Available with or without porosity B (70 - 100 m) fritted disc sealed in. Order column, flow control adapter and clamp separately.
-
Instatherm Desicator, Vacuum Oven
Ace Glass250mm dia with bottom Instatherm® heated,(low voltage: 40 volts, 10 amps max.) Top is not heated, but has insulation cover. May be used as a vacuum oven at temps up to 180 degrees C continuously. The top has an observation stripe for visibility & is supplied with vacuum take-off valve. Uncoated…
-
Support Rods Stainless Steel
Ace Glass303 stainless steel support rods, 13mm (1/2") O.D. for use in place of aluminum or fiberglass. For use with all standard laboratory connectors.
-
Condenser, Liebig, No Hold Up
Ace GlassWith standard taper or spherical joint at bottom and top. Hose connections are size D.
-
Heat Transfer Block - Microscale
Ace GlassAluminum heat transfer block, 9594-12 for use in place of a glass sand bath in Microscale experiments. Offers excellent heat transfer and will not interfere with magnetic stirring. Block has four holes for vials and one hole for thermometers. 9594-16 for use on top of stirrer-hot plate to effect…
-
Stir Shaft, 4 Blade Propeller, PTFE
Ace GlassPTFE covered stainless steel shaft with solid PTFE, 4 blade screw propeller. Blades are pitched 45 degrees. For a better grip by the stir motor chuck, 50mm of stainless is left exposed.
-
Offset gearbox and motors complete with right angle drive unit for pilot plant systems. Motors with right-angle drive save headspace and work well where height is restricted. Available for standard or hazardous duty applications. Available in either 1/4hp or 1/2hp with a digital 115/230v 50/60Hz…
-
Precision ground glass stirring shaft, 10mm OD, attached vanes. Vanes will fit through a 45/50 joint and are contoured for use with our 9448 and 9456 series Mini-Lab flasks. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 and 8055. Compatible with our 8050 mechanical…
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8074 stainless steel or 8075 polished 10mm od glass shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…
-
PTFE agitator with removable blade secured with a PTFE pin. Supplied 3.2x15.2cm blade will fit through a 45/50 joint. Fits 19mm od drilled type or knob type 8076, 8078 & 8079 shafts.
-
Condenser, Long Path
Ace GlassTurbulent flow created makes this condenser very desirable for use under reduced pressure. Internal and external cooling surfaces result in high efficiency per unit length. Joints are standard taper 24/40.
-
Stirrer, Complete
Ace GlassTrubore stirrer assembly consists of the standard taper outer glass bearing, PTFE inner bearing, glass-filled PTFE bushing and lock nut, compression seal saddle o-ring, PTFE blade and either a glass or stainless stir shaft.
-
Condenser, Liebig
Ace GlassWith straight inner tube sealed through the jacket. This condenser is acceptable for use with Abderhalden or Mini-Lab moisture test apparatus.
-
Stirring shaft agitator combination available in either a solid, precision ground glass shaft or all PTFE knob type shaft with a PTFE snap-fit agitator designed to fit through 14/20 and 18/11 joints. Designed for use with our 5mm ID 9524 or 9527 bearings and flasks of 50ml and smaller.
-
Bearing, Trubore, Water Cooled, 19mm
Ace GlassTrubore bearing, jacketed, spherical joint. Designed to accomodate our 8112-10 packing box. For use with 8077 & 8078 19mm od precision ground glass shafts or 8079 PTFE covered shafts. Spherical joint can be clamped to prevent rotation. Trubore length of 15.2cm or 6 inches.
-
Column has standard taper 24/40 joint at top and 2 mm bore stopcock at the bottom with Por. B (70-100m) fritted disc sealed into the bottom of tube.
-
Support stand assembly for bench scale size Chromatography columns. "H" shaped base stand and 122cm high stainless steel rod gives great stability for the larger bench scale columns. Stand comes complete with base, rod, support plate with hole, clamp holder, chain clamp and cork ring.
-
Circulator Hose Support
Ace GlassAll stainless steel, fully adjustable clamps for securing and supporting circulator hoses used with jacketed pilot plants. The universal clamps adjust to any pipe style pilot plant stand, and the clip will accommodate any standard circulator hose size.
-
Column, Chromatography
Ace GlassLarge chromatography columns with o-ring grooved flat flanged tops and Ace-Thred bottoms. Column extenders and 5860 heads should be mated to columns with our 6517 series clamps. All columns and extenders are supplied with either a 7855-254 (4") or 7855-260 (6") silicone o-ring. For capfe o-rings,…
-
Extraction Apparatus Liquid-Liquid
Ace GlassDesigned for U.S.E.P.A. Priority Pollutant analysis using Method 625 (base neutrals/acid extractables). Accommodates 1L sample and approximately 200mL of a heavier-than-water extracting solvent. Features an extractor body designed to accept a common condenser with a 45/50 joint, a 24/40 opening…
-
Condenser, Air Reflux
Ace GlassMicroscale air condenser normally used in reflux experiments. When packed with desiccant material, condenser becomes a drying tube. With inner joint at bottom, outer joint at top. Codes -10, -14 and -17 supplied with drip tip for use with 9595 Spinning Band Column. Effective length, approximately…