Ace Glass, Equipment
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 28mm agitators will fit drilled type 8080 shafts.
-
Column, Chromatography, Jacketed
Ace GlassColumns are fully jacketed including internally threaded ends for circulation of heat exchange media. A wide choice of upper and lower end pieces can be fitted to columns using 5837, 5838, 5840, 5841, 5842 and 5843 fittings. Available in variety of diameters and lengths. Not for use with 5819 fittings.
-
Bearing, Trubore, Pressure, 10mm
Ace GlassDesigned for use with #25 Ace-Thred. Consists of a Trubore bearing, pressure bushing, gland with two O-Rings and retainer bushing with o-ring. For use with our precision ground stirring shafts (8068,8070, 8071,8073,9532,9533) and reservoir as part of our 7898 Thin Film reaction system.
-
Stirring Shaft, PTFE Coated Glass, 10mm
Ace GlassPrecision ground glass stirring shafts, 10mm OD, button type, PTFE coating permits higher stirring speeds with Trubore bearings. If used unlubricated, 500 rpm max with water-cooled 8040 bearing. Compatible with 8036, 8038, 8039, 8043, 8047, 8051, 8055 and 13443 bearings. Button type shafts accept…
-
Condenser, Cold Finger
Ace GlassCold Finger accessory for standard Allihn type condensers. This cold finger has a 24/40 inner joint that fits inside the condenser's upper outer joint and tube to provide added cooling ability and faster condensation. Fits into 5943, 5945, and 5946 con
-
Stirring Blade, For 5 & 6mm Shaft
Ace GlassPTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.
-
Chromatographic Column, With Filter Disc
Ace GlassChromatographic column with 24/40 joint at top, 2 mm bore 1:5 taper solid PTFE stopcock plug at bottom and porosity B (70 - 100 m) fritted disc sealed near bottom of tube. These columns also appear in expanded listing under 5871.
-
Precision ground glass stirring shaft with attached vanes, 10mm. For use when agitation and gas introduction are desired at the same time. Agitator will fit through a 45/50 joint. Designed for use with our 9523 Trubore bearing and 9443 or 9446 mini-lab flask heads. Introduced gas exits the hollow…
-
Stirring shaft agitator combination available in either a solid, precision ground glass shaft or all PTFE knob type shaft with a PTFE snap-fit agitator designed to fit through 14/20 and 18/11 joints. Designed for use with our 5mm ID 9524 or 9527 bearings and flasks of 50ml and smaller.
-
Extractor, Soxhlet
Ace GlassSoxhlet extactor body with standard taper outer joint at top and 24/40 standard taper inner joint at bottom.
-
Stirring Shaft, Unground, 9mm
Ace GlassUnground, 9mm OD shaft for use in liquid seal bearings and our debris free 8098 and 8099 stirrer assemblies. Code -25 is a button type shaft which accepts our 8083, 8084, 8085 and 8086 blades. Shaft length accomodates flasks from 500ml to 5000ml.
-
Chromatographic Column, 1:5 PTFE Plug
Ace GlassChromatographic column with 2mm bore 1:5 taper solid PTFE stopcock plug at bottom.
-
Simple absorption chromatography column for rapid preparative separations with moderate resolution. Allows separations of samples from 0.01 to 10.0g in 10-15 minutes. Column and reservoir, only, are Epoxy Coated. Reservoir connects between column and flow control adap-ter. Joints on column,…
-
Safety Shield, Plastic, Michel-Miller
Ace GlassAcrylic safety shield and polyethylene cap for use with Michel-Miller Columns to insure safe operation at pressures to 300 psi. Top thread of column is hung in polyethylene cap; cap is then held by the plastic shield. Clamp the shield, not the column.
-
Bulb type for use with regular extraction apparatus. Improved design permits greater condensing capacity. Jacket lengths approximately 255mm with one bulb per 50mm.
-
Pass-Thru Rod, Flexible shaft
Ace GlassPass-thru rod for use with Caframo 13565 & 13566 stir motors attached to our 8081 flexible stirring shaft.
-
Clamp, Reaction Flask, Two-Piece
Ace GlassPositive, two-piece clamp for securing flat flanges as found on our 6504,6511 & 6516 reaction flasks. Powder coated, high strength aluminum clamp features three brass tilting bolts which will swing freely away from the top piece upon loosening the secu
-
Adjusta-chrom, Column, Michel-Miller
Ace GlassA combination of the high performance, low pressure Michel-Miller Chromatography Line and Adjusta-Chrom Recycling Column. Top has adjustable fitting that allows for a bed height anywhere within 1 - 6" below thread. Plunger tip is all PTFE with a porosity C (25-50m) glass disc. Complete column…
-
Agitator, PTFE, 4 Blade
Ace Glass4 Blade PTFE agitator available with either 45 or 90 degree blade angle. For use with glass or metal shafts and is secured using a compression style fitting allowing it to positioned anywhere along the length of the shaft.
-
Instatherm Oil Baths, High Form
Ace GlassTall, heavy-walled glass vessels coated with Instatherm® to accommodate larger and taller vessels. A thermocouple well is imbedded in the insulation. Designed to operate at up to 250 degrees C. Do not run dry or above max voltage. Bare, flat bottom suitable for use with magnetic stirrers. All…
-
Condenser, Spiral
Ace GlassWith spiral condensing tube having both inlet and outlet connections at top, on same side. With joints. Length between joints is approximately 80-90 mm longer than the stated coil length. Available with PTFE clad bottom joint.
-
Lab Stand Support Shelf
Ace GlassLab stand support shelf fits any stand with up to 5/8"od rod. Stand measures 7 x 10" and is available with or without 4" rubber-bordered center hole. Manufactued from light, cast aluminum and epoxy coated. Rod mounted codes -04 & -06 feature a 5/8in OD x 12in long stainless rod with a through hole…
-
Instatherm Beaker, Griffin Low Form
Ace GlassInstatherm® Griffin style beaker with pouring spout. Designed to operate at up to 250 degrees C. Do not run dry or above max voltage. degrees per minute), with very low thermal lag. The bottom is uncoated Bare, flat bottom suitable for use with magnetic stirrers. All baths include a connecting…
-
Precision ground, hollow, 5mm glass stirring shaft. Button type shaft accepts 9542 blades and can be used in matching 9524 and 9527 bearings. Holes are provided in the side of the shaft for material introduction and at the bottom for emission into the flask contents. Join to stirrer motor using…
-
Condenser, Allihn
Ace GlassBulb type, approximately one bulb per 50 mm, with various joint sizes at bottom and top. Available with hose barbs or Ace-Safe connectors.,/p>
-
Chlorofluorocarbon grease for use at speeds up to 6000 r.p.m. with ACE standard glass assemblies. Use 8040 water-cooled type bearing for long-time stirring (over one hour). Below one hour, 8038 type may be used at 1500 r.p.m.; eight hours at 1000 r.p.m. High chemical inertness unaffected by strong…
-
Instatherm Desicator, Vacuum Oven
Ace Glass250mm dia with bottom Instatherm® heated,(low voltage: 40 volts, 10 amps max.) Top is not heated, but has insulation cover. May be used as a vacuum oven at temps up to 180 degrees C continuously. The top has an observation stripe for visibility & is supplied with vacuum take-off valve. Uncoated…
-
Extractor, Soxhlet, with Stopcock
Ace GlassExtractor body only, with stopcock for withdrawing samples from extraction chamber. Can be used interchangeably with the standard Soxhlet extraction apparatus.
-
Buchi Steam Tube, Rotary Evaporator
Ace GlassReplacement glass steam tube for Buchi rotary evaporators using the C or CR assemblies.
-
Chuck, Flex-Grip®
Ace GlassNylon chuck for use with ACE stirring shafts or other shafts of the same dimensions. Chuck has flexible insert which allows for misalignment of shaft without danger of breakage.
-
Cords, Connecting, Instatherm & UV Lamps
Ace GlassInstatherm connecting cords, codes -16 & -20 feature in-line fuse protection against surges and high voltage. Code -16 fits our earlier style baths, pre 2009, while code -20 features a twist-lok socket used in our current baths. Code -05 fits a wishbone connector commonly used on the lid of…
-
Thermocouple Sensor, Julabo, Pt100
Ace GlassJulabo Pt100 sensors in stainless steel or PTFE coated stainless