Ace Glass, Equipment
-
Condenser, Spiral
Ace GlassWith spiral condensing tube having both inlet and outlet connections at top, on same side. With standard taper joints. Length between joints is approximately 80-90 mm longer than the stated coil length.
-
Condenser, Allihn
Ace GlassBulb type, approximately one bulb per 50 mm, with 24/40 standard taper inner joint at bottom.
-
1mL Tissue Grinder, Dounce Type
Ace GlassThe Dounce type, glass tissue grinder is supplied with two glass pestles; one with a tight inner tolernace and one with a loose inner tolernace. The loose pestle can be used for initial reduction of the tissue sample and the tight pestle can be used to fine grind the tissue and complete the homogenation.
-
The improved design of ACE extractor condensers permits greater condensing capacity, cycling rates may be doubled over conventional style extractors. Complete consists of flask cap, condenser, extractor, and flask.
-
Micro cold finger condenser with drip tip on bottom for directing drops into the well of 14/10 jointed 9576 or 9599 Hickman Stills. Cold water is introduced into cold finger periodically by means of a Pasteur pipet. Complete item consists of cold finger condenser and multi- purpose vacuum adapter…
-
Instatherm Desicator, Vacuum Oven
Ace Glass250mm dia with bottom Instatherm® heated,(low voltage: 40 volts, 10 amps max.) Top is not heated, but has insulation cover. May be used as a vacuum oven at temps up to 180 degrees C continuously. The top has an observation stripe for visibility & is supplied with vacuum take-off valve. Uncoated…
-
Condenser, Friedrichs
Ace GlassReflux controlled by regulating jacket temperature. Provides compact spiral path for condensation. Jacket length 200mm. Bottom standard taper 24/40 joint.
-
Chromatographic column with integral reservoir and #15 Ace-Thred at top, and 2mm bore 1:5 taper PTFE plug at bottom. Column supplied with 7506-06 Nylon bushing and FETFE O-Ring. Complete item consists of column with bushing and O-Ring, and 5853-07 Tubing Connector for connecting 12.5 to 14mm O.D.…
-
Simple absorption chromatography column for rapid preparative separations with moderate resolution. Allows separations of samples from 0.01 to 10.0g3 in 10-15 minutes. Column and reservoir, only, are Epoxy Coated. Reservoir connects between column and flow control adap-ter. Joints on column,…
-
Temperature Sensors, K & T type
Ace GlassType K temperature probes provide economical measurement from -20 degrees C to 550 degrees C with more corrosion resistance than J type probes. Type T probes are commonly used for temperature ranges from -200 degrees C to 200 degrees C. Probes available with an inconel sheath or insulated wire.…
-
Precision ground glass stirring shaft with attached vanes, 10mm. For use when agitation and gas introduction are desired at the same time. Agitator will fit through a 45/50 joint. Designed for use with our 9523 Trubore bearing and 9443 or 9446 mini-lab flask heads. Introduced gas exits the hollow…
-
Distilling Column, Jacketed
Ace GlassJacket length 250 mm, with indents for supporting glass beads or other packing.
-
Support Ring, Solid PTFE
Ace GlassUseful for supporting column, flasks, dishes, etc. Shaped with internal bevel.
-
Condenser, Air Reflux
Ace GlassMicroscale air condenser normally used in reflux experiments. When packed with desiccant material, condenser becomes a drying tube. With inner joint at bottom, outer joint at top. Codes -10, -14 and -17 supplied with drip tip for use with 9595 Spinning Band Column. Effective length, approximately…
-
Heavy duty, 28mm O.D. glass stirring shaft for use with ACE 12845 reactors. Shafts are pre-drilled to accommodate 8091,8093 & 8101 agitators for 28mm od shafts. Recommended for use with either our 8067 Trubore™ bearing with debris trap or our 8050 non-shedding bearing. For motor connection,…
-
Condenser, Allihn
Ace GlassBulb type, approximately one bulb per 50 mm, with various joint sizes at bottom and top. Available with hose barbs or Ace-Safe connectors.,/p>
-
Powerstat Mounting Bracket
Ace GlassMounting bracket permits easy and convenient mounting of 12080 or 12081 Powerstats on standard laboratory racks or stands having up to 16mm O.D. rods. Made of strong, rust and corrosion resistant aluminum alloys. Bracket is attached to the bottom of the powerstat by two screws and to the rack or…
-
Condenser, Friedrichs
Ace GlassWith molded spiral condensing surface and joint at bottom and top. Jacket length 250mm. Available in various joint sizes with hose barbs or Ace-Safe connectors.
-
Stirrer, Laboratory, Solid State
Ace GlassTotally enclosed, 1/40hp DC permanent magnet motor with dual 8 mm (5/16") armature and gear shafts with milled flats. Armature shaft with maximum speed of 4000rpm.; 18:1 ratio gear shaft rated 3.6in-lb torque, up to 333rpm. Motor supplied with 1.5 meter 3-wire cable for controller connection.…
-
By closing stopcock, serves as a reflux condenser; open serves as a still head for Claisen type distillation. Top joint can be used for thermometer or cold finger condenser insertion. Side vent enables head to be used in vacuum distillation. Jacketed section 140mm.
-
Replacement condenser for Buchi rotary evaporators. Available plain or safety coated. Includes PTFE hose barbs,GL caps and plug.
-
Agitator, PTFE, Large Scale Multi-blade
Ace GlassThese heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 28mm agitators will fit drilled type 8080 shafts.
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8076 (19mm od) or 8080 (28mm od) polished glass stir shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…
-
Button type, solid glass stirring shafts, 5 & 6mm OD. Precision ground shafts, codes -04 & -06, should be used in matching glass Trubore 9524 and 9527 bearings. Polished shaft, code -40, should be used only in our 8066-120, 6mm PTFE inner bearing. All accept our 9542 blades. Join to stirrer motor…
-
Clamp, Two-Piece, Flat Flange
Ace GlassTwo-piece unfinished aluminum clamp with PTFE gaskets and brass tightening bolts. Code -03 fits our 7646-18 75mm o-ring joint and our 7519 (76mm) filter support assembly. Code -05 fits our 7519 (102mm) filter support assembly and our 6504 kettles with
-
Clamp, Quick Release
Ace GlassStainless Steel Quick Release clamp for use with two-piece Pressure Reaction Flasks and Heads with Duran flanges. Available with or without rod for clamping to support frame. Note: Ensure proper bottom support for your reactor, the clamp is only recommended for stabilization, not support.
-
Support Stand, Bench-Top
Ace GlassStand assembly for 1L to 6L bench reactors. Fits both filter and pressure reactor styles as well as standard round bottom flasks. It will accomodate flasks with or without bottom valves. The motor mount raises and lowers as does the flask support system. This aids in aligning the flask, motor and…
-
Bearing, Trubore, Gas Balancing, 10mm
Ace GlassThis bearing is supplied with tubulation for feeding inert gases around the bearing to balance any pressure possibly being developed in the flask. Can also be used for gas-liquid reactions and gas dispersions using our hollow precision ground stirring shafts (8068, 9532).
-
Instatherm Beaker, Griffin Low Form
Ace GlassInstatherm® Griffin style beaker with pouring spout. Designed to operate at up to 250 degrees C. Do not run dry or above max voltage. degrees per minute), with very low thermal lag. The bottom is uncoated Bare, flat bottom suitable for use with magnetic stirrers. All baths include a connecting…
-
Stirring bars with large, 25mm (1 inch) raisied center ring.
-
Extractor, Soxhlet
Ace GlassSoxhlet extactor body with standard taper outer joint at top and 24/40 standard taper inner joint at bottom.