Ace Glass, NEW! Life Science
-
Condenser, Spiral
Ace GlassWith spiral condensing tube having both inlet and outlet connections at top, on same side. With standard taper joints. Length between joints is approximately 80-90 mm longer than the stated coil length.
-
Condenser, Allihn
Ace GlassBulb type, approximately one bulb per 50 mm, with 24/40 standard taper inner joint at bottom.
-
1mL Tissue Grinder, Dounce Type
Ace GlassThe Dounce type, glass tissue grinder is supplied with two glass pestles; one with a tight inner tolernace and one with a loose inner tolernace. The loose pestle can be used for initial reduction of the tissue sample and the tight pestle can be used to fine grind the tissue and complete the homogenation.
-
The improved design of ACE extractor condensers permits greater condensing capacity, cycling rates may be doubled over conventional style extractors. Complete consists of flask cap, condenser, extractor, and flask.
-
Micro cold finger condenser with drip tip on bottom for directing drops into the well of 14/10 jointed 9576 or 9599 Hickman Stills. Cold water is introduced into cold finger periodically by means of a Pasteur pipet. Complete item consists of cold finger condenser and multi- purpose vacuum adapter…
-
Instatherm Desicator, Vacuum Oven
Ace Glass250mm dia with bottom Instatherm® heated,(low voltage: 40 volts, 10 amps max.) Top is not heated, but has insulation cover. May be used as a vacuum oven at temps up to 180 degrees C continuously. The top has an observation stripe for visibility & is supplied with vacuum take-off valve. Uncoated…
-
Condenser, Friedrichs
Ace GlassReflux controlled by regulating jacket temperature. Provides compact spiral path for condensation. Jacket length 200mm. Bottom standard taper 24/40 joint.
-
Chromatographic column with integral reservoir and #15 Ace-Thred at top, and 2mm bore 1:5 taper PTFE plug at bottom. Column supplied with 7506-06 Nylon bushing and FETFE O-Ring. Complete item consists of column with bushing and O-Ring, and 5853-07 Tubing Connector for connecting 12.5 to 14mm O.D.…
-
Simple absorption chromatography column for rapid preparative separations with moderate resolution. Allows separations of samples from 0.01 to 10.0g3 in 10-15 minutes. Column and reservoir, only, are Epoxy Coated. Reservoir connects between column and flow control adap-ter. Joints on column,…
-
Distilling Column, Jacketed
Ace GlassJacket length 250 mm, with indents for supporting glass beads or other packing.
-
Support Ring, Solid PTFE
Ace GlassUseful for supporting column, flasks, dishes, etc. Shaped with internal bevel.
-
Condenser, Air Reflux
Ace GlassMicroscale air condenser normally used in reflux experiments. When packed with desiccant material, condenser becomes a drying tube. With inner joint at bottom, outer joint at top. Codes -10, -14 and -17 supplied with drip tip for use with 9595 Spinning Band Column. Effective length, approximately…
-
Condenser, Allihn
Ace GlassBulb type, approximately one bulb per 50 mm, with various joint sizes at bottom and top. Available with hose barbs or Ace-Safe connectors.,/p>
-
Powerstat Mounting Bracket
Ace GlassMounting bracket permits easy and convenient mounting of 12080 or 12081 Powerstats on standard laboratory racks or stands having up to 16mm O.D. rods. Made of strong, rust and corrosion resistant aluminum alloys. Bracket is attached to the bottom of the powerstat by two screws and to the rack or…
-
Condenser, Friedrichs
Ace GlassWith molded spiral condensing surface and joint at bottom and top. Jacket length 250mm. Available in various joint sizes with hose barbs or Ace-Safe connectors.
-
By closing stopcock, serves as a reflux condenser; open serves as a still head for Claisen type distillation. Top joint can be used for thermometer or cold finger condenser insertion. Side vent enables head to be used in vacuum distillation. Jacketed section 140mm.
-
Replacement condenser for Buchi rotary evaporators. Available plain or safety coated. Includes PTFE hose barbs,GL caps and plug.
-
Clamp, Two-Piece, Flat Flange
Ace GlassTwo-piece unfinished aluminum clamp with PTFE gaskets and brass tightening bolts. Code -03 fits our 7646-18 75mm o-ring joint and our 7519 (76mm) filter support assembly. Code -05 fits our 7519 (102mm) filter support assembly and our 6504 kettles with
-
Clamp, Quick Release
Ace GlassStainless Steel Quick Release clamp for use with two-piece Pressure Reaction Flasks and Heads with Duran flanges. Available with or without rod for clamping to support frame. Note: Ensure proper bottom support for your reactor, the clamp is only recommended for stabilization, not support.
-
Support Stand, Bench-Top
Ace GlassStand assembly for 1L to 6L bench reactors. Fits both filter and pressure reactor styles as well as standard round bottom flasks. It will accomodate flasks with or without bottom valves. The motor mount raises and lowers as does the flask support system. This aids in aligning the flask, motor and…
-
Instatherm Beaker, Griffin Low Form
Ace GlassInstatherm® Griffin style beaker with pouring spout. Designed to operate at up to 250 degrees C. Do not run dry or above max voltage. degrees per minute), with very low thermal lag. The bottom is uncoated Bare, flat bottom suitable for use with magnetic stirrers. All baths include a connecting…
-
Extractor, Soxhlet
Ace GlassSoxhlet extactor body with standard taper outer joint at top and 24/40 standard taper inner joint at bottom.
-
Column has standard taper 24/40 joint at top and 2 mm bore stopcock at the bottom with Por. B (70-100m) fritted disc sealed into the bottom of tube.
-
Condenser, Long Path
Ace GlassTurbulent flow created makes this condenser very desirable for use under reduced pressure. Internal and external cooling surfaces result in high efficiency per unit length. Joints are standard taper 24/40.
-
Adsorption Column
Ace GlassUsed in ASTM D1319-65T, a "test for hydrocarbon types in liquid petroleum products." This unit is fabricated from ACE Trubore tubing. Tip is attached to column by means of a 12/2 spherical joint. Upper joint spherical 28/12.
-
Pipet, Dispensing, Automatic
Ace GlassFills and pours automatically, rapidly. One head for all capacities, all volumes. Short tipping angle, interchangeable volumetric bulbs give reproducable volumes. Bulb joint is 14/20, head and flask 29/42. Complete apparatus consists of head, flask, volumetric bulb, clip, two 19mm (3/4-in) springs,…
-
Condenser, Graham
Ace GlassWith standard taper 24/40 outer joint at top. Hose connections are size D, for 3/8in ID tubing.
-
Condenser, West
Ace GlassNo Hold Up West condenser available with hose barbs or Ace-Safe connectors.
-
Chromatographic column with integral reservoir for connecting 5872 Flow Control Adapter. With 2mm bore, 1:5 taper solid PTFE stopcock plug at bottom. Available with or without porosity B (70 - 100 m) fritted disc sealed in. Order column, flow control adapter and clamp separately.
-
Column, Chromatography
Ace GlassWith 24/40 standard taper joint at top and a 2 mm bore stopcock at the bottom.
-
Distilling Column
Ace GlassVacuum jacketed and silvered with observation stripe. Also available unsilvered. With an enlarged bulb knockdown section that removes high boiling ends without choking. Length of packing section is 100 or 200mm, I.D. approximately 10mm. With indents to
-
Adapter, Injection Port, Michel-Miller
Ace GlassA simple, all PTFE septum injector. Allows direct, on-column injection to the center of the filter disc at top of column without stopping the solvent flow through the 1/4"-28 female side thread (with or without helicoil). Locknut design provides leaktight seal without o-rings. You can order the…