Ace Glass, Shaft Stirrers, Stirrers
-
Stirring Shaft, PTFE Coated Glass, 10mm
Ace GlassPrecision ground glass stirring shafts, 10mm OD, button type, PTFE coating permits higher stirring speeds with Trubore bearings. If used unlubricated, 500 rpm max with water-cooled 8040 bearing. Compatible with 8036, 8038, 8039, 8043, 8047, 8051, 8055 and 13443 bearings. Button type shafts accept…
-
Precision ground glass stirring shaft with attached vanes, 10mm. For use when agitation and gas introduction are desired at the same time. Agitator will fit through a 45/50 joint. Designed for use with our 9523 Trubore bearing and 9443 or 9446 mini-lab flask heads. Introduced gas exits the hollow…
-
Chlorofluorocarbon grease for use at speeds up to 6000 r.p.m. with ACE standard glass assemblies. Use 8040 water-cooled type bearing for long-time stirring (over one hour). Below one hour, 8038 type may be used at 1500 r.p.m.; eight hours at 1000 r.p.m. High chemical inertness unaffected by strong…
-
Stirring shaft agitator combination available in either a solid, precision ground glass shaft or all PTFE knob type shaft with a PTFE snap-fit agitator designed to fit through 14/20 and 18/11 joints. Designed for use with our 5mm ID 9524 or 9527 bearings and flasks of 50ml and smaller.
-
Agitator, PTFE, 4 Blade
Ace Glass4 Blade PTFE agitator available with either 45 or 90 degree blade angle. For use with glass or metal shafts and is secured using a compression style fitting allowing it to positioned anywhere along the length of the shaft.
-
Chuck, Flex-Grip®
Ace GlassNylon chuck for use with ACE stirring shafts or other shafts of the same dimensions. Chuck has flexible insert which allows for misalignment of shaft without danger of breakage.
-
Stirring Blade, For 5 & 6mm Shaft
Ace GlassPTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.
-
Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique 3 piece design of Trubore inner bearing, compression seal nylon bushing and glass standard taper adapter allows for moderate misalignment of stir motor and the bearing cannot sieze the shaft. For use with 8077 & 8078 19mm od…
-
Bearing, Trubore, Ace-Thred, 10mm
Ace GlassSelf-aligning, three-piece bearing. Complete consists of inner Trubore bearing, Nylon bushing with O-Ring, and threaded adapter. Unique design eliminates costly replacement since inner bearing will spin if shaft binds or will self-align at O-Ring seal in the event the motor is slightly cocked.…
-
Stirrer, Vacuum, Debris Free
Ace GlassA rugged, compact, inexpensive stirrer. The upper member turns with stirring shaft, bottom member remains stationary. Upper member supplied with vinyl connector. Use with ACE 8134 stirring shafts. Assembly may also be used to make your own rotary evaporator.
-
Stirrer, Complete
Ace GlassTrubore stirrer assembly consists of the standard taper outer glass bearing, PTFE inner bearing, glass-filled PTFE bushing and lock nut, compression seal saddle o-ring, PTFE blade and either a glass or stainless stir shaft.
-
PTFE agitator with removable blade secured with a PTFE pin. Supplied 3.2x15.2cm blade will fit through a 45/50 joint. Fits 19mm od drilled type or knob type 8076, 8078 & 8079 shafts.
-
Agitator, PTFE, Turbine, For 10mm Shaft
Ace GlassAll-PTFE turbine type agitator. Unique locking arrangement assures positive grip. Agitator fits 10 mm shafts. Shaft opening is drilled straight thru to allow positioning of agitator at any drilled position on shaft as well as the bottom. For use with bead type glass shafts, 8068-G, 8075 or PTFE…
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8074 stainless steel or 8075 polished 10mm od glass shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…
-
Stirrer, Complete
Ace GlassPrecision Trubore Stirrer Assembly consisting of 10 mm ID bearing, bushing, precision ground, button type glass shaft and blade. Available with either glass or PTFE stir blade.
-
Bearing, Trubore, 10mm
Ace GlassFor use with Flask Head 9443. By using precision bore tubing throughout the length of the bearing, a stirrer is produced that will hold to within 1mm of vacuum and withstand pressures in the flask up to 300mm. The 9532 Agitator, used with this bearing actually develops a negative pressure of 230mm…
-
Polished stainless steel stirring shafts, 10mm OD, drilled type with removable button. When used with 8066 PTFE bearing, a lubricant-free vacuum seal can be realized at speeds up to 200 rpm. Recommended for use with 8044,8050,8066,13443 and 13445 bearings. With button, shaft accepts…
-
STIR-LUBE®,Trubore® Stirrer Lubricant
Ace GlassA superior, low melting, silicone base lubricant which liquefies at body temperature. Because of its composition, you need apply only a very thin film of Stir-Lube® to a stirring shaft to increase bearing and shaft life at least three times over that of a bearing lubricated with glycerine.…
-
Precision ground glass stirring shafts, 19mm OD, hollow. Button type shafts accept 8085 blades and can be used in all 19mm ID Trubore 8059, 8060, 8061 and 8065 bearings. Compatible with our 8050 mechanical seal and 13445 PTFE Debris-free bearings. Join to stirrer motor using 8124 series chucks.
-
Ultra-Vacuum stirrer bearing for applications up to 0.6 Torr. Non-shedding bearing is manufactured from PTFE, Rulon and PEEK materials. Equally good in both vacuum and pressure applications as low as 0.6 Torr. Rated for up to 400 rpm with both glass (polished rather than precision ground is best)…
-
Bearing, Trubore, Plain, 10mm
Ace GlassInterchangeable bearing designed to be used with our precision ground stirring shafts (8068,8070,8071,8073,9532,9533). Recommended top stirring speed with our 8117 Stir-Lube is 1500 rpm.
-
Bearing, Trubore, Gas Balancing, 10mm
Ace GlassThis bearing is supplied with tubulation for feeding inert gases around the bearing to balance any pressure possibly being developed in the flask. Can also be used for gas-liquid reactions and gas dispersions using our hollow precision ground stirring shafts (8068, 9532).
-
Precision ground glass stirring shafts, 10mm OD, paddled, button type and bead type. Button type shafts accept 8083, 8085, 8086, 8087 & 8096 stir blades. Beaded shafts accept 8088, 8089, 8090 & 8091 agitators. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 & 8055.…
-
Bearing, Trubore, Pressure, 10mm
Ace GlassDesigned for use with #25 Ace-Thred. Consists of a Trubore bearing, pressure bushing, gland with two O-Rings and retainer bushing with o-ring. For use with our precision ground stirring shafts (8068,8070, 8071,8073,9532,9533) and reservoir as part of our 7898 Thin Film reaction system.
-
316 stainless steel, football shaped, stir blades for 10mm OD button type stir shafts. Holed versions, codes -70 thru -74, provide even greater agitation. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
Precision ground glass stirring shafts,10mm OD, crescent type. Useful for stirring viscous materials at low rpm. Available for round bottom flasks of 1, 3 and 5 liters. Code -19, 3 liter size will fit a 2 liter flask, but closely. Flask opening must be 29/42 or larger. Use with Trubore bearings…
-
Bearing, Trubore, Water Cooled, 19mm
Ace GlassTrubore bearing, jacketed, spherical joint. Designed to accomodate our 8112-10 packing box. For use with 8077 & 8078 19mm od precision ground glass shafts or 8079 PTFE covered shafts. Spherical joint can be clamped to prevent rotation. Trubore length of 15.2cm or 6 inches.
-
Collar, Stir Shaft
Ace GlassDesigned to be used with 8068, 8070, 8071, 8074 or 8078 stirring shafts. Handy for positioning shaft in bearing, and preventing shaft from dropping into flask. Supplied with PTFE gasket to prevent scratching top of bearing and acts as dust cover. Available in either Glass-filled PTFE or 316…
-
Stirring Shaft, Glass, Polished, 10mm
Ace GlassPolished glass stirring shafts, 10mm OD. Recommended for use with only our 8050,8066,13443 and 13445 bearings. Join 8083,8085,8086,8087,8096 blades to button type shafts. Join 8088, 8089, 8090 & 8091 agitators to bead type shafts. Plain shafts will accept 8094 & 8095 agitators secured with a…
-
Agitator, PTFE, Large Scale Multi-blade
Ace GlassThese heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.
-
Agitator, PTFE, Large scale, Turbine
Ace GlassA turbine type agitator, available for 19mm and 28mm shafts. 19mm six blade agitators are open in the center to allow custom positioning on drilled type or knob type 8076, 8078 & 8079 shafts. 28mm four blade agitators are supplied with a PTFE nut & bolt set for securing to 8080 shafts. Shaft is not included.
-
Stirring Shaft, Unground, 9mm
Ace GlassUnground, 9mm OD stirring shaft design for use with our 9528 vacuum and debris free stirrer assembly. 380mm straight section, 416mm overall length. Use our 9530-08 blade.