Ace Glass, Glass
-
Baffles, Glass or PTFE
Ace GlassUse Ace-Thred adapters to mate glass or PTFE (stainless steel core) baffles to any standard taper joint. See 5028 & 5030 series adapters. Baffles can be adjusted vertically or rotated to increase agitation.
-
Flask Head, PTFE-Clad Bottom Joint
Ace GlassInterchangeable Mini-Lab head with 45/50 bottom joint, PTFE-Clad. No grease needed, will not freeze. Top 19/38 center joint, and are 14/20 side necks are ground. See 9443-20 for head with PTFE-Clad bottom joint and polished top joints. Side arms are placed at proper angles so that the thermometer…
-
Distillation Apparatus, Short Path
Ace GlassDesigned for small quantities where holdup between flask and receiver must be minimized but where it is also desired to measure vapor temperature with an accuracy compared to large setups. Improved thermometer sensitivity. Physical carry-over is practi
-
Adapter, Mini #7 Ace-Thred
Ace GlassAdapter with #7 Ace-Thred and inner or ball joint. Used for probes, thermometers, electrodes, etc.
-
Distilling Head
Ace GlassWith condenser jacket on side arm. Thermometer joint is 10/30 (see 8315 for thermometer listing). Side arm is at a 75 degree angle.
-
Reaction Flask Head
Ace GlassConical 4" neck for use with 6475, 6476, 6477, 6479, 6480, 6481, 6491, 6492, 6497, 6498 and 9656 ACE Reaction Flasks. Supplied with three outer joints. Use 6496 Clamp for securing to flasks.
-
Distillation Apparatus, Trap-to-Trap
Ace GlassUsed for the removal of solvents or other volatiles by vacuum distillation at ambient temperature. When used with Schlenk reaction Vessel, No. 7756, the trap prevents excessive loss of solution in the event of a bump. The distillate is collected in a No. 9477 pear shaped flask or other suitable…
-
Complete, two-piece, plain flask with bottom outlet, pressure reactor system designed to perform low to moderate positive pressure reactions, synthesis and catalysis. Reactor capacities range from 500ml to 5000ml and use Ace-Threds to achieve a leak-tight system. Two-piece (flanged flask and head)…
-
Adapter, Vacuum Take-off, Short Stem
Ace GlassOuter joint at angle of 105 degree. Hose connection opposite top joint. Stem below joint, 30mm.
-
Adapter, Thermocouple Well
Ace GlassA special well fabricated from glass that is worked to a very thin wall for better heat transfer. Fabricated in two sizes for either 25mm or 76mm immersion, length of tube being measured from the bottom of the ground joint.
-
Straight connecting adapter with standard taper inner joints at both ends. Various lengths.
-
Adapter, 75 degree Angle
Ace Glass75 degree adapter, standard taper top joint, standard taper or ball joint bottom and side.
-
Jacketed glass immersion well for use with our 7825 series lamps within our 6962,7863,7864,7865 & 7891 series reactors. Codes -30 & -40 feature a small diameter glass inner feed tube to ensure the flow of coolant from the bottom of the well up to the outlet. Codes -35 & -45 feature a PTFE inner…
-
Hose Connections, Large
Ace GlassRing-style hose connections for use on large soxhlet condensors, etc. With flare end. Sold in shelf-packs of 12 each.
-
Joints, Inner Member, Microscale
Ace GlassStandard taper inner ground joints used in fabrication of ACE Microscale Glassware. Use with 7609 outer member. Codes -11, -12 and -13 have drip tip.
-
Adapter, pH Probe Tube, Pilot Plant
Ace GlasspH probe adapter tube extends the probe deep within large capacity flasks. Fits in 45/50 opening on head and is vertically adjustable along its length. Available with either Chemraz or Fetfe o-rings and in 24 in(61cm), 36 in (91cm), or 48 in (122cm) le
-
Adapter, 15mm o-ring joint to standard taper inner joint , fetfe o-ring included.
-
Power Supply, Photochemical
Ace GlassCased, open "core and coil" type transformers that supply the extra voltage and current required to initiate the lamp's arc and reduce operational power. Intended for use with our 7825 or 7883 series photochemical lamps. Carefully choose the correct power supply for your environment (voltage and Hz…
-
Available with standard taper or spherical joint. Stem below joint is 250mm. Hose connection is size C.
-
Adapter, Bleed, Capillary
Ace GlassLength measured from top of joint to tip. Hose connection is size A.
-
Adapter, Straight connecting
Ace GlassStraight connecting adapter with standard taper outer joints top and bottom. Various lengths.
-
Distillation Column, Vacuum jacketed
Ace GlassLarge distillation columns, jacketed with internal expansion bellows. Outer jacket baked out and evacutaed to 10-6 Torr. Columns are silvered internally with observation stripe. All columns are supplied with the proper number of bellows to withstand the 180 Deg C temperature differential at all…
-
Distilling Head, Hennion Design
Ace GlassFor variable reflux ratio, can be used for operation under vacuum and receiver can be removed without disturbing the system's vacuum. 10/30 thermometer joint takes 76mm immersion thermometer listed under 8315. Side arm joint is 24/40. Stopcock bores are 2 mm.
-
Adapter, 15mm o-ring joint to standard taper inner joint, porosity B (70-100 micron) frit, fetfe o-ring included.
-
Adapter, Septum Inlet, Two Ports
Ace GlassSampling adapter with joint at bottom and two septum at top for handling air-sensitive materials. Supplied with two septa.
-
Dilatometer, Volumetric
Ace GlassFor use in any reaction where there is a change in volume. Described in Experiments in Physical Chemistry, Shoemaker & Garland, 1962, by McGraw-Hill Book Company, Inc. Experiment 27. Capacity of bath is 75mL, bulb 50mL, with capillary tube graduated from 0.0cm at bottom to 15.0cm at top. I.D.…
-
Dilatometer, A.O.C.S.
Ace GlassFor determination of fat and oil constants. Described in A.O.C.S., Method Cd 10-57. Total volume of precision bore capillary is 1.400 mL plus or minus 0.015mL. The smallest graduation is 0.005mL. Complete with stopper and hooks. Both stopper and tube are numbered.
-
Filter Reactor, All PTFE
Ace GlassAll PTFE filter reactor; an extension of the famous Ace borosilicate glass filter reactor product line. The head, head joints, body, stirrer bearing, valved bottom filter assembly, and stir shaft with agitator are all PTFE. Filter support is polypropylene. Large, Ace-Thred bottom filter assembly…
-
Drying Apparatus, Modified Abderhalden
Ace GlassVacuum. Desiccant tube has two-way action that permits the use of a smaller desiccant volume and better air contact with desiccant. During the final stage of drying, the T-bore stopcock is turned so that the evacuation path is directly over the desiccant, while in the early stages the desiccant is…
-
Hose Connections, Mini-Lab Size
Ace GlassRing-style hose connections for use on small-scale apparatus such as Mini-Lab. Codes -05 & -09 are on straight tubing; code -14 has a flare end. Sold in shelf-packs of 12 each.
-
Moisture Test Receiver
Ace GlassModified Bidwell & Sterling with overflow to allow excess solvent to return to boiling flask. Both capacities are calibrated in 0.1mL subdivisions. Joints are standard taper 24/40.
-
Vapor Duct Tube, For Rotary Evaporators
Ace GlassReplacement vapor duct tube for Buchi rotary evaporators. The 45mm length fits V assemblies and the 160mm length fits A assemblies. End joints are available in [ST] 29/32, [ST] 24/40, or [ST] 29/42 inner. The middle joint is tooled to fit the specific rotary evaporator for which it was designed.…