Accessory for model F48000 Thermolyne benchtop muffle furnace. Dimensions (L x W x H) Exterior 10 x 7.6 x 0.38 in. (25.4 x 19.3 x 0.95cm) Dimensions (L x W x H) Exterior 10 x 7.6 x 0.38 in. (25.4 x 19.3 x 0.95cm) - See more at: http://www.thermoscientific.com/en/product/benchtop-muffle-furnaces-accessories.html#sthash.DQyZgrMn.dpuf

Heating elements on support tubes radiating freely into the furnace chamber provide for particularly short heating times for these models. Thanks to their robust lightweight refractory brick insulation, they can reach a maximum working temperature of 1300 °C. These models thus represent an…

GCF1400 series controlled atmosphere furnaces feature a chamber with Mitsubishi (Japan) high quality alumina fiber insulation and SiC heating elements. A double walled steel internal housing helps minimize heat loss to exterior surface. Furnace operation is controlled by Shimaden (Japan) 40-segment…

High-quality insulation materials made of vacuum-formed fiber plates enable energy-saving operation and a fast heating time due to low heat storage and heat conductivity. By using different gas supply systems, operations can be performed under non-flammable or flammable protective or reactive gases…

The Thermo Scientific Thermolyne Industrial Benchtop Muffle Furnace has a B1 single-setpoint digital controller with ramp and dwell, 2.2L (0.08 cubic foot) heating area capacity, and a temperature range of 100 to 1,200 degrees C for general laboratory use. Four heating elements embedded in…

These tube furnaces can be used for horizontal (RSH) operation. The split-type design makes it easy to change the working tube. It allows for a comfortable exchange of various working tubes (e.g. working tubes made of different materials). Using the wide range of accessories these professional…

This weighing furnace with integrated precision scale and software, was designed especially for combustion loss determination in the laboratory. The determination of combustion loss is necessary, for instance, when analyzing sludges and household garbage, and is also used in a variety of technical…

Ai TFM3 series 1600°C 3-zone tube furnaces use SiC and MoSi2 as their heating elements. Furnace hearth is built with Mitsubishi (Japan) high quality fiber materials. Temperature of this furnace is controlled by high precision temperature controller (Shimaden fp93 from Japan) with +/-1°C…

These compact tube furnaces with SiC rod heating and integrated switchgear and controller can be used universally for many processes. With an easy to replace working tube as well as additional standard equipment options, these furnaces are flexible and can be used for a wide range of applications.…

CF1100 4x4x4" compact muffle furnaces with 30 segments programmable up to 1050°C. Great for small sample heating in research or dental labs. They can also be easily placed inside a glove box if desired. All our furnaces are CE compliant. Please note: Wire heating element DOES NOT have warranties.

1200°C maximum temperature 120 or 350 cu. in. capacities Built-in vent port Highly thermal-efficient ceramic insulation surrounding the chamber achieves maximum energy efficiency. Open coil heating elements on both sides of chamber enable rapid heating with minimal temperature…

GCF1700 series controlled atmosphere furnaces feature a chamber with Mitsubishi (Japan) high quality alumina fiber insulation and MoSi2 heating elements. A double walled steel internal housing helps minimize heat loss to exterior surface. Furnace operation is controlled by Shimaden (Japan)…

These compact tabletop tube furnaces with integrated control systems can be used universally for many processes. Equipped with a standard working tube of C 530 ceramic and two fiber plugs, these furnaces have an unbeatable price/performance ratio. Tmax 1200°C or 1300°C …

CF1800 series muffle furnaces feature a chamber with Mitsubishi (Japan) high quality grade 1900 alumina fiber insulation and the famous Kanthal (Sweden) molybdenum silicide (MoSi2) heating elements. A dual-wall steel housing helps minimize heat loss to exterior surface. Furnace operation is…

CF1400 series muffle furnaces feature a chamber with Mitsubishi (Japan) high quality alumina fiber insulation and silicon carbide (SiC) heating elements. A double walled steel internal housing helps minimize heat loss to exterior surface. Furnace operation is controlled by Shimaden (Japan)…

Robust design and choice of four temperature controllers, ideal for industrial applications including ashing organic and inorganic samples and conducting gravimetric analysis. Spacious 14L (0.5 cu. ft.) capacity and reaches a maximum of 1200°C Four heating elements are located on…

CF1700 series muffle furnaces feature a chamber with Mitsubishi (Japan) high quality grade 1800 alumina fiber insulation and molybdenum silicide (MoSi2) heating elements. A dual-wall steel housing helps minimize heat loss to exterior surface. Furnace operation is controlled by Shimaden (Japan)…

These fast-firing furnaces are ideal for simulation of typical fast-firing processes up to a maximum firing temperature of 1300°C. The combination of high performance, low thermal mass and powerful cooling fans provides for cycle times from cold to cold up to 35 minutes with an opening…

The high-temperature furnaces HTC 16/16 - HTC 450/16 are heated by vertically hung SiC rods, which makes them especially suitable for sintering processes up to a maximum operating temperature of 1550°C. For some processes, e.g. for sintering zirconium oxide, the absence of interactivity between…

For added protection, the door safety switch stops power to heating elements when door opens Thermocouple break protection cuts power to heating elements, preventing a thermocouple failure runaway condition Two open coil heating elements on chamber sides assure fast heat-up with minimum…

Ramsbottom PYREX® For determination of carbon residue left on evaporating oil Meets ASTM D 524

These furnaces are especially used for the assay of precious metals and ashing processes where the insulation and heating must be protected from emerging gasses and vapours. The furnace chamber forms a ceramic muffle which can easily be replaced. The assay furnace is equipped with an integrated…

GCF1200 series controlled atmosphere furnaces feature a chamber with Mitsubishi (Japan) high quality alumina fiber insulation and the famous Kanthal (Sweden) heating elements. A double walled steel internal housing helps minimize heat loss to exterior surface. Furnace operation is controlled by…

For operation up to 1100°C (1980°F) These models also serve as Ashing Furnaces Side hinge door keeps the furnace hot face away from the user Atmosphere vent allows for atmosphere removal, ventilation and air injection Safety interlock system disconnects the power to the…

Small benchtop muffle furnaces Maximum temperature range of 1200°C Four controller types: A. Basic automatic B. Single setpoint C. 4 ramp, 4 dwell D. 8 ramp, 8 dwell with RS 232 Highly thermal-efficient ceramic insulation surrounding the chamber achieves maximum energy efficiency. Open…

Moldatherm® ceramic fiber insulation with embedded heating elements provides fast heat-up and recovery Setpoint and actual temperatures are displayed simultaneously on controller Heat-reflecting inner shell creates two insulating air spaces Fast, reliable, cost-effective answer for those…

The RD tube furnaces convince with their unbeatable price-performance ratio, very compact outer dimensions and their low weight. These all-rounders are equipped with a working tube which also serves as support for the heating wires. Thus, the working tube is part of the furnace heating which has…

High performance muffle furnace with a microprocessor-controlled thermo-regulator characterized by excellent repeatability and features temperature resistant paint. High accuracy controller for better operability and visibility.  Excellent heat tightness with a firmly sealed chamber…

Features Available in two popular chamber sizes Double shell design for lower external cabinet temperature with energy savings Moldatherm® high temperature ceramic fibre insulation with advanced graded design for fast heat-up and resistance to thermal shock Vertically hinged…

Thermostatically controlled coking furnace for five samples Conforms to ASTM D 524 and related specifications Microprocessor temperature control with digital display and over-temperature cut-off Reaches standard test temperature of 550°C rapidly and controls with…

Program segments into Thermo Scientific™ Lindberg/Blue M™ Box and Tube Furnace Controllers for increased temperature accuracy. Features overtemperature control and multiple segment configuration; designed to work with the 1200°C split-hinge and 1500°C box furnaces. …

Heating elements on support tubes radiating freely into the furnace chamber for short heat up times, Tmax of 1400°C, heating from two sides, dual shell housing made of sheets of textured stainless steel for low external temperatures and stability, adjustable air inlet in the furnace door,…