Kemtech America, Supplies, Glass
-
SYNTHWARE Dessicant Flask
Kemtech AmericaDessicant Flask, Joint: 34/45, with 2mm bore PTFE stopcock.
-
Synthware Rotary Evaporator Anti-Splash Traps with Fritted Discs
Kemtech AmericaSynthware rotary evporator anti-splash trap with extra coarse fritted disc. Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. the frit reducesfoam from being carryover. With upper outer and lower inner standard taper joints.
-
Synthware Inlet Adapters with Hose Connection
Kemtech AmericaAdapter has a Nylon compression cap and a Viton o-ring to form a vacuum tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. The 8mm hose connection can be used for N2/Ar introduction or vacuum. Supplied with one Nylon cap and one Viton o-ring.
-
SYNTHWARE Hickman-Hinkle Still Head with Side Port
Kemtech AmericaHickman-Hinkle Still Head, with Side Port, Synthware, Joint: 14/10, for microscale fractional distillation, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.
-
Synthware Vacuum Take-Off Adapters, Short Stem
Kemtech AmericaSynthware vacuum take-off adapter with drip tip. For use in vacuum distillation. Adapter is bent at 105 degrees. Serrated hose connection is attached to vacuum source. With standard taper top outer joint and lower inner joint of the same size.
-
SYNTHWARE Distillation Receivers
Kemtech AmericaWith the outer and inner joint at 135° angle, used with short-path.
-
-
SYNTHWARE Microscale Distillation Head
Kemtech AmericaWith 2mm glass stopcock and 24/40 joint. Supplied with a special 25mL long-neck flask for small volume efficiency.
-
SYNTHWARE Sublimators
Kemtech AmericaSublimator, Two Piece, Synthware, Various sizes are available. O-Ring Size: 217, 226, or 229, Clamp Size: 35, 65, or 75 available.
-
SYNTHWARE Claisen Adapter
Kemtech AmericaClaisen Adapter, Microscale, Synthware, Joints: 14/10, supplied with two compression caps, two Viton O-rings and two PTFE-faced silicone septum.
-
SYNTHWARE Kugelrohr Distilling Bulbs
Kemtech AmericaKugelrohr Distilling Bulb Capacity: 5, 10, 15, 25 or 50mL available Joints: 14/20, Bulb O.D.: 25, 31, 35, 42 or 48mm available Overall Height: 80, 85, 90, 98 or 105mm available Used in distillation of very small amount of distillate at lower temperature with high efficiency.
-
Synthware Vacuum Adapters with Glass Stopcocks, 90°
Kemtech AmericaSynthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper inner joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.
-
SYNTHWARE Gas Inlet/Outlet Adapter
Kemtech AmericaGas Inlet/Outlet Adapter, Microscale, Synthware, Joint: 14/10, Hose Connection OD: 8mm.
-
Synthware Inert Gas Adapters with 2 Hose Connections
Kemtech AmericaSynthware Inert Gas Adapter has two hose connections 180 degrees from one another to provide a flow of inert gas over the apparatus. The joints are standard taper inner joints.
-
SYNTHWARE Peptide Synthesis Vessels, Solid Phase
Kemtech AmericaPeptide Synthesis Vessel, Solid Phase, Synthware, Capacity: Available in sizes ranging from 10-50mL, Frit Porosity: Coarse or Medium, Frit Diameter: Available in sizes ranging from 15-25mm, GL Thread: 14 or 25 available, Arm OD: 8mm, Supplied with a PTFE lined cap and straight bore PTFE stopcock…
-
SYNTHWARE Short Path Distilling Head for Volatile Solvents
Kemtech AmericaWith the condenser being a combination of a cold coil and Leibig. Top outer joint is a 10/18 for use with a 50mm immersion thermometer. For best result, use D272440.
-
Synthware Distillation Adapters, 75°
Kemtech AmericaSynthware distillation adapter bent at 75 degrees. Both ends are standard taper inner joints and are the same size.
-
SYNTHWARE Jacketed Micro Vigreux Distillation Head
Kemtech AmericaDistillation Head, Vigreux, Jacketed Thermometer Joint: 10/18 Joints: 14/20, use with 25mm immersion thermometer
-
Synthware Vacuum Adapters, Outer Joint
Kemtech AmericaSynthware vacuum adapter has a standard taper outer joint and a serrated hose connection. Ideal for use as a vent or for the introduction of pressure/vacuum.
-
Synthware Distilling Adapters, 105°
Kemtech AmericaSynthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints.
-
SYNTHWARE Short Path Distilling Head with 24/40 Joint
Kemtech AmericaOne-piece design for easy set-up. For the best result, use D272440 distillation receiver. To be used with 25mm immersion thermometer.
-
Synthware Rotary Evaporator Anti-Splash Traps
Kemtech AmericaTrap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With upper outer and lower inner standard taper joints.
-
SYNTHWARE Hickman Still Head
Kemtech AmericaHickman Still Head, Synthware, Joint: 14/10, for microscale fractional distillation, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.
-
Kjeldahl Trap Adapters
Kemtech AmericaSynthware distillation adapter with Kjeldahl trap. With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is approximately 200mm.
-
Synthware Claisen Adapters
Kemtech AmericaProvides dual entry into a variety of flasks. Adapter has standard taper outer joints at top and on side and inner joint on bottom. All joints are the same size.
-
SYNTHWARE Solvent Still Head, High Vacuum Valves
Kemtech AmericaSolvent Still Head, High Vacuum Valves Capacity: 250mL Joints: 24/40 Valve Size: 0-4mm
-
Peptide Synthesis Vessel, Solid Phase, Vacuum, Synthware, Capacity: 10-100mL available, Frit Porosity: Medium abd Coarse availabe, Frit OD: 15-40mm available, GL Thread: 14 or 25 available, Hose Connection OD: 8mm, Supplied with PTFE lined screw cap and straight bore stopcock with 2mm bore.
-
Synthware Connecting Adapters
Kemtech AmericaSynthware combination adapting connector with a top spherical socket joint and a lower standard taper inner joint.
-
SYNTHWARE Short Path Vaccum Jacketed Distillation Apparatus
Kemtech AmericaUsed with 25mm immersion thermometer, and D27 distillation receiver.
-
Synthware Vacuum Adapters with Outer Joints & Glass Stopcocks
Kemtech AmericaSynthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper outer joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.
-
Synthware Bushing Adapters
Kemtech AmericaSynthware bushing adapters allow for compact assemblies of dissimilar standard taper joints.
-
Synthware Flow Control Adapters with Metering Stopcock, 90°
Kemtech AmericaSynthware flow control adapter with metering stopcock. The serrated hose connection is turned 90 degrees to the standard taper inner joint. Provides on/off control with the main stopcock and precise control of liquids or gasses with the needle valve.