Kemtech America Lab Glassware
-
Synthware Kjeldahl Distilling Trap Adapters
Kemtech AmericaAdapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top outer and lower inner standard taper joints.
-
Synthware Reducing Adapters
Kemtech AmericaSynthware reducing adapters are used for connecting dissimilar standard taper joint sizes. The lower inner joint is larger in size than the top outer joint.
-
Synthware Vacuum Adapters with 1:5 Teflon® Stopcocks
Kemtech AmericaSynthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper inner joint. The PTFE stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.
-
Synthware Straight Drying Tubes
Kemtech AmericaSynthware straight drying tube. With top outer and lower inner standard taper joints of the same size.
-
SYNTHWARE Vacuum Jacketed Vigreux Distillation Heads
Kemtech AmericaVacuum jacketed Vigreux distillation head having a sealed on condenser, braced for strength. Vacuum adapter has an inner joint and a sealed in drip tip. To be used with a 25mm immersion thermometer .
-
Synthware Inlet Adapters
Kemtech AmericaSynthware inlet adapter with a standard taper inner joint. Design allows introduction of reactants below the surface. The serrated hose connections have an O.D. of 10 mm.
-
SYNTHWARE Vacuum Takeoff Adapter
Kemtech AmericaVacuum Takeoff Adapter, Microscale, Synthware, Joint: 14/10, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.
-
SYNTHWARE Dean Stark Distillation Receivers
Kemtech AmericaFor easy separation of water from reaction or distillation system.
-
Synthware Rotary Evaporator Anti-Splash Traps
Kemtech AmericaTrap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With upper outer and lower inner standard taper joints.
-
Synthware Vacuum Take-Off Adapters with Glass Stopcocks
Kemtech AmericaSynthware vacuum adapter with 2mm straight bore glass stopcock on the hose connection.The upper outer and lower inner standard taper joints are the same size.
-
Synthware Claisen Adapters
Kemtech AmericaProvides dual entry into a variety of flasks. Adapter has standard taper outer joints at top and on side and inner joint on bottom. All joints are the same size.
-
SYNTHWARE Distilling Receivers with Tubes
Kemtech AmericaSupplied with distribution adapter, three 12mL receiver tubes and three plastic joint clip. With 135° angle between top outer joint and lower inner joint.
-
Synthware Distilling Adapters, 105°
Kemtech AmericaSynthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints.
-
SYNTHWARE Microscale Distillation Apparatus
Kemtech AmericaMicroscale Distillation Apparatus has a short-path design for microscale application, used with 25mm immersion thermometer, and D27 distillation receiver.
-
Synthware Vacuum/Inert Gas Adapters
Kemtech AmericaAllows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection is at a 90 degree angle to the standard taper inner joint.
-
SYNTHWARE Solvent Still Head, Repurification
Kemtech AmericaSolvent Still Head, Repurification Joint: 24/40
-
Peptide Synthesis Vessel, Solid Phase, Vacuum, Synthware, Capacity: 10-100mL available, Frit Porosity: Medium abd Coarse availabe, Frit OD: 15-40mm available, GL Thread: 14 or 25 available, Hose Connection OD: 8mm, Supplied with PTFE lined screw cap and straight bore stopcock with 2mm bore.
-
SYNTHWARE Short Path Distilling Head for Volatile Solvents
Kemtech AmericaWith the condenser being a combination of a cold coil and Leibig. Top outer joint is a 10/18 for use with a 50mm immersion thermometer. For best result, use D272440.
-
SYNTHWARE Vertical Orientation Distrubution Adapter
Kemtech AmericaRotating distillation receiver allows four fractions to be collected. Vacuum adapter has a vertical orientation.
-
SYNTHWARE Kugelrohr Distilling Bulbs
Kemtech AmericaKugelrohr Distilling Bulb Capacity: 5, 10, 15, 25 or 50mL available Joints: 14/20, Bulb O.D.: 25, 31, 35, 42 or 48mm available Overall Height: 80, 85, 90, 98 or 105mm available Used in distillation of very small amount of distillate at lower temperature with high efficiency.
-
SYNTHWARE Glass Check Valves
Kemtech AmericaCheck Valve, All Glass, Synthware, Hose Connections OD: 8mm, with ground seat for liquid seal.
-
Synthware Inlet Adapters with Extra Coarse Discs
Kemtech AmericaSynthware inlet adapter with an extra coarse porosity fritted disc between the serrated hose connection and the standard taper inner joint. The disc prevents solids from being introduced into the reaction system during liquid transfer.
-
Kjeldahl Trap Adapters
Kemtech AmericaSynthware distillation adapter with Kjeldahl trap. With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is approximately 200mm.
-
Synthware Rotary Evaporator Traps
Kemtech AmericaSynthware rotary evaporator trap. Anti-climb design. Trap provides expanded volume for reactions that have a tendency to foam excessively. The inner vapor tube is sealed to the top of the trap to prevent entry into the condenser.
-
Synthware Connecting Adapters
Kemtech AmericaSynthware combination adapting connector with a top spherical socket joint and a lower standard taper inner joint.
-
SYNTHWARE Distillation Receiving Set
Kemtech AmericaComes with Synthware Distilling Adapter (Joints: 14/20, 19/22 AND 24/40) and Cow Receivers (Joints: 14/20, 19/22, AND 24/40). Rotating cow receiver allows four flasks to be progressively filled. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**
-
SYNTHWARE Thermometer Adapter with Hose Connection
Kemtech AmericaThermometer Adapter, Vacuum, Microscale, Synthware, Joints: 14/10, Thermometer OD: 5.0-7.5mm, supplied with one compression cap and one Viton O-ring.
-
Synthware Inlet Adapters with Hose Connection
Kemtech AmericaAdapter has a Nylon compression cap and a Viton o-ring to form a vacuum tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. The 8mm hose connection can be used for N2/Ar introduction or vacuum. Supplied with one Nylon cap and one Viton o-ring.
-
SYNTHWARE Inlet Connecting Adapter
Kemtech AmericaInlet Connecting Adapter, High Vacuum Valve Joint: #15 O-ring Valve Size: 0-4mm Side Port: 10mm OD.
-
Synthware Enlarging Adapters
Kemtech AmericaSynthware enlarging adapters are used for connecting dissimilar standard taper joint sizes. The lower inner joint is smaller in size than the top outer joint.
-
Synthware Rotary Evaporator Vapor Ducts
Kemtech AmericaSynthware rotary evaporator vapor duct. Precision ground and polished. Meet manufacturer's standards. With standard taper inner joint.
-
SYNTHWARE Sublimators
Kemtech AmericaSublimator, Two Piece, Synthware, Various sizes are available. O-Ring Size: 217, 226, or 229, Clamp Size: 35, 65, or 75 available.