Receiving Flask

Compare Tool

Select up to 3 products

Receiving Flask
1 - 32 of 96
Sort
View
Show
  • Receiving Flasks

    Heidolph

  • These flasks are available in sizes from 50 to 3000 mL and come with ball joint KS-35. All flasks are also available with P+G coating. The P+G coating protects against mechanical damage and provides efficient protection against glass splinters in the event of a breakage.

  • Replacement receiving flask adapters for Buchi rotary evaporators. Joins steam tube to receiving flask. Combi-clip not included.

  • ….45µm. Our flasks have a wide bottle opening for easy access and pouring of your samples, and the funnel is manufactured from optically clear polystyrene. The bottle and filter adapter are manufactured from 100% virgin polypropylene. Filtration bottle tops without receiver bottles are…

  • Ai 35/20 standard taper joint, heavy wall 1000mL round bottom receiving flask.

  • Replacement flask for Buchi rotary evaporators. Round bottom flasks with a 35/20 single neck and safety coating.

  • High quality glass drain port with PTFE open/close valve for Ai 3L, 5L, 10L, 20L receiving flasks. Glass material: high borosilicate glass 3.3

  • Borosilicate glass receiving flask for all large scale rotary evaporators. Available in safety coated or plain glass. Side neck includes a SVL thread vent cap. Bottom inner ball joint includes CAPFE o-ring. Dark amber coated glass version is also available.

  • Graduated, round bottom receiving flask for use with all rotary evaporators. 35/20 spherical outer joint will also mate to 35/25 ball joints. 250ml & 500mL size graduated in 10ml increments, 1000ml & 2000ml in 100ml increments.

  • With short neck and outer joint. Available in standard and heavy wall. Heavy wall approximately 30% heavier than standard wall.

  • New design jacketed receiving flask. Fits all rotary evaporators. Outer jacket has 28/15 o-ring ball joints to seal to chiller hoses. Has an SVL thread vent cap on side joint. Bottom DN25 ball joint has CAPFE o-ring. Jacket inlet and outlet ball joints have FETFE o-rings.

  • Round bottom, HEAVY WALL single short neck flask for use on rotary evaporators for receiving distillate. Joint at the top of the flask is a 35/25 socket. Plastic Coated to prevent injury from broken glass while preventing spillage of hazardous materials.

  • Comes with Synthware Distilling Adapter (Joints: 14/20, 19/22 AND 24/40) and Cow Receivers (Joints: 14/20, 19/22, AND 24/40). Rotating cow receiver allows four flasks to be progressively filled. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

  • An excellent all-purpose receiver for general distillation work. Equipped with a complete stopcock manifold to allow contents of the receiver to be removed to a single receiving flask without disturbing the vacuum of the system. Stopcocks are 4 mm bore.Tubing connections are 10mm O.D. olive type.

  • Radial style distillation receiver allows four flasks to be progressively filled. Upper vacuum adapter is bent at a 105º angle. Complete item consists of a vacuum adapter, distribution adapter, four of the listed size flasks with hooks and ten CG-110 stainless steel springs.

  • …walled borosilicate glass viscosity flask has a top with reinforced lip and is used in determining Saybolt viscosity of petroleum and bituminous materials. This receiving flask can be used in Saybolt viscometer baths. Conforms to ASTM D 88 specifications. Each flask is provided with a marking spot…

  • receiving flask, receiving flask clip, stopcock, PTFE fill tubes, and set of GL-14 hose connections and caps. 1230E20 - Type A Condenser, Diagonal, can be used where height is limited, For standard distillations, evaporating flask feed via stop-cock. Includes 1L P+G receiving flask, receiving

  • The three 25mL flasks are in the same plane, rotated about the condenser axis. Hose connection is parallel to and above condenser axis. Three clips are supplied for holding flasks to condenser. All joints are 14/20. Hose connection is size A.

  • Similar to CG-1279 but with the top outer joint vertical instead of a 105° angle. Complete item consists of a vacuum adapter, distribution adapter, four of the listed size flasks with hooks and ten CG-110 stainless steel springs.

  • ,p>Especially designed receiver to draw samples during distillation or to return the condensed vapor to the flask. Capacity 125ml, available with or without 1:5 PTFE plug.

  • …with Interface I-300 / I-300 Pro when combined with optional level sensor for secondary condenser that alerts potential overflow of the receiving flask Reliable High chemical resistance due to the use of high quality materials Increased lifetime thanks to speed-controlled…

  • …disturbing distillation pressure. Joints are 24/40. Receiver is 5 mL. Hose connection is size B, for use with 5/16in (7.9mm) or 3/8in (9.5mm) ID tubing. For version with 14/20 joints, or PTFE- clad version with 14/20 joints, see 9400. For 50 mL flask, see 6887-20. For joint clip, see 7598-24.

  • …of residual solvent vapor after the pump. At the same time it separates any liquid solvent from the pump, putting it directly into the receiving flask. Insulation sleeves prevent the formation of undesirable condensation and produce the condenser with effective protection against mechanical…

  • …of residual solvent vapor after the pump. At the same time it separates any liquid solvent from the pump, putting it directly into the receiving flask. Insulation sleeves prevent the formation of undesirable condensation and produce the condenser with effective protection against mechanical…

  • Distillation apparatus for obtaining separate fractions while maintaining constant pressure. Code -10 complete unit features ground joints and four 9458-02 5ml flasks. Code -25 complete unit features PTFE clad joints and four 9458-02 5ml flasks.

  • Radial style distillation receiver allows four flasks to be progressively filled. Upper vacuum adapter is bent at a 105° angle.

  • Reusable Filter Holders with Receiver

    Thermo Scientific Nalgene

    …funnels For 47 mm diameter membrane filters Eliminates the need for a manifold and/or breakable glass vacuum flask Particularly useful for field work Receiver is graduated Non-sterile Autoclavable Two side-arms allow connection to vacuum line; also accepts syringe…

  • Description:    Glassware vertical including condenser, evaporating flask and receiving flask Volume (mL ) :  1000 Frosted:   29/32

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.