Ace Glass
-
PTFE Gasket
Ace GlassDesigned to fit 8068, 8070, 8071, 8074 or 8078 stirring shafts. Useful as dust cover and as replacement for gasket supplied with 8127 collar. Twelve to a package.
-
Distilling Column, Vigreux
Ace GlassWith standard taper 24/40 joints. Length in centimeters refers to the effective length of the column as measured from the lowest to the highest indent of the column.
-
Manifold, Vacuum
Ace GlassAll-glass-and-PTFE vacuum manifold with three, four or five stopcock ports. Each port is a variable opening, 0-10mm, high vacuum threaded stopcock. Plugs are PTFE with Nylon or PTFE handles and FETFE O-Rings. Ultimate vacuum of 10-7 can be realized with O-Rings as supplied. For bakable systems,…
-
Distillation Apparatus, Cyanide
Ace GlassApparatus for converting simple and most complex cyanides into HCN and for from most interferences before measuring by titration or colorimetric analysis examination of industrial wastes and other water. Method is described in Standard the Examination of Water and Wastewater. Fourteenth Edition,…
-
Reaction Flask
Ace GlassWith 4 mm bore stopcock for rapid removal of contents without disturbing the general arrangement of the apparatus. 4 inch ID conical flange requires Ace product family 6496 clamp for securing the head to the flask.
-
1mL Tissue Grinder, Dounce Type, Glass
Ace GlassThe Dounce type, glass tissue grinder is supplied with two glass pestles; one with a tight inner tolernace and one with a loose inner tolernace. The loose pestle can be used for initial reduction of the tissue sample and the tight pestle can be used to fine grind the tissue and complete the homogenation.
-
Bottle, Gas Washing
Ace GlassDreschel, high form with standard taper 24/40 joint on all sizes. Stopper and bottles available separately.
-
Instatherm Reaction Flask and Head
Ace GlassRugged cylindrical reaction flask and head with Duran, flat, ground 4" flange with O-Ring groove and integral heating element that eliminates the local superheating commonly associated with more conventional heating methods and eliminates cumbersome and dangerous oil baths. Response is rapid and…
-
Adapter, Enlarging
Ace GlassConnecting, enlarging adapter with top female joint being larger than the bottom male joint.
-
Fully flexible drive shaft facilitates isolation of the stirrer motor from the reactor. Complete units, code -30 (91.4cm) and code -32 (152.4cm), designed for use with 8mm (5/16in) motor shaft. Purchase the optional code -27 adapter for motors with 9.5mm (3/8in) shafts. Reactor end consists of a…
-
Filter Reactor, Plain
Ace GlassSmall volume filter Reactor. Complete item includes: Reactor Body, head (14/20 joints), Clamp, PTFE Bottom Adapter with CAPFE O-Ring, 350 micron polypropylene screen support, 100 micron polyethylene support, 5844 Adapter, 5839-42 Shutoff Valve, 8066-12
-
Condenser, Liebig
Ace GlassWith straight inner tube sealed through the jacket. This condenser is acceptable for use with Abderhalden or Mini-Lab moisture test apparatus.
-
A liquid-liquid extractor for use with lighter or heavier-than-water extracting solvents. Overflow and boil-up tube uses Ace-Thred Connections, thus allowing easy removal for cleaning to reduce cross contamination among samples. Complete consists of:Extractor Body, (approx.1.3L capacity),…
-
Specially designed, standardized flasks, with stoppers. All capacities have 12/18 joint with approximately 10 mm opening. Cylindrical body affords better mixing and drainage, and ease of withdrawal using pipets. Wide base offers greater stability. Uppe
-
-
Adapter, Twin, Ace-Thred
Ace GlassTwin adapter features two Ace-Thred top openings and a standard taper inner joint bottom. With the supplied nylon bushings, two tubes or a thermometer and bleed tube can be inserted through the same joint. The 24/25 medium length joint is compatible wi
-
Feed Tube, Luer Tip
Ace GlassPermits packing of column without excessive drop impact. Also used for side arm introduction of effluent or may be used for pressurized operation. Used in conjunction with 5029 Nylon bushing. Supplied straight only. Tube is 8 mm O.D. with luer connection.
-
Manifold, Vacuum
Ace GlassGlass Manifold with #15 Ace-Thred at either end To allow switching 5853 vacuum connection to left or right side. Supplied with three or five, 4mm straight bore PTFE stopcock sampling ports. (Additional ports can be ordered.) Overall length of glass manifold is 230mm. Complete item consists of 8763…
-
Tube, Gas Dispersion
Ace GlassWith porous fritted glass tip. Available in 150mm and 300mm lengths. O.D. of both lengths, 10mm. Fits through #11 Ace-Thred.
-
Ultra-Vacuum stirrer bearing for applications up to 0.6 Torr. Non-shedding bearing is manufactured from PTFE, Rulon and PEEK materials. Equally good in both vacuum and pressure applications as low as 0.6 Torr. Rated for up to 400 rpm with both glass (polished rather than precision ground is best)…
-
Distilling Head,, Solvent Recovery
Ace GlassVersatile, for use as a solvent recovery still for azeotropic separations of solvents, either heavier or lighter than water. As a solvent recovery unit, the lower 4mm PTFE double oblique stopcock permits total return to flask, total takeoff, and total storage in the 500mL graduated receiver. Bottom…
-
Condenser, Spiral
Ace GlassWith spiral condensing tube having both inlet and outlet connections at top, on same side. With standard taper joints. Length between joints is approximately 80-90 mm longer than the stated coil length.
-
Round bottom, single neck flask with a beaded tube end well.
-
Adapter, Offset, Ace-Thred
Ace GlassThermometer adapter with inner joint at bottom and top threaded piece offset and angled approximately 10 degree for use in multiple neck flasks. Threaded Nylon bushing tightens into glass piece to form an O-Ring compression seal with thermometers, blee
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 28mm agitators will fit drilled type 8080 shafts.
-
Stopcock adapter, top outer joint, bottom inner joint, glass plug. Spherical joint versions are both outer joints top and bottom.
-
Bottle, Solution, Plastic Coated
Ace GlassCoated to neck with PVC safety coating to reduce potential breakage and exposure to laboratory personnel when handling hazardous material. Carboy style bottles with sloping shoulders. Necks are tooled for uniform fit with stoppers. Uses No. 12 stopper
-
-
Purge Adapter, Rotary Evaporator
Ace GlassGlass purge adapters for use with popular brands of rotary evaporators. Top has 35/25 socket joint for joining with the trap or condenser. The bottom has a 35/25 ball joint for connecting to the receiver flask. The middle or purge tube has either a 2mm PTFE stopcock or a 2mm valve to allow for…
-
Circulator Adapters, Universal
Ace GlassAce Glass universal pilot plant / circulator adapters and fittings designed for use with various manufacturer's circulators and our reaction systems.
-
Immersion Well, Photochemical, Quartz
Ace GlassDouble-walled, quartz Immersion Well for use with 7825-30, -32, -34, and -36 lamps. With inlet and outlet tubes for cooling or modified with a 4.8mm I.D. PTFE tube attached to a glass tube and secured with a #7 Ace-Thred bushing. Inlet tube extends down the annular space to insure flow of coolant…
-