Glass and Glassware, Cannabis
-
Kjeldahl Trap Adapters
Kemtech AmericaSynthware distillation adapter with Kjeldahl trap. With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is approximately 200mm.
-
Midget Bubblers, Graduated
ChemglassMicro impinger designed for sampling of small volumes of air at low jet velocity, as per EPA Method 6. Impinger bottle is graduated from 5 to 30mL in 5mL subdivisions. Both the bottle and stopper have 24/40 standard taper joints. The nozzle being replaced with an extra coarse fritted gas dispersion…
-
Similar to the AF-0450 5-port line, except that the line is constructed using 0-4mm Chem-Vac™; Chem-Cap®; valves (A) instead of the CG-468-02 greased glass stopcocks on all of the 4-ports. The end cap on the vacuum line is a #30 o-ring joint while the inert gas line has a #9 o-ring joint…
-
Synthware Distilling Adapters, 105°
Kemtech AmericaSynthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints.
-
Adapter has a coarse frit sealed between the #15 o-ring joint and the standard taper inner joint. Frit permits filtration of large particles before introduction into the flask and also serves as a bump trap for reactions being performed in flasks while connected to the manifold. Each adapter is…
-
Synthware Rotary Evaporator Anti-Splash Traps
Kemtech AmericaTrap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With upper outer and lower inner standard taper joints.
-
Adapter Univ Sz 21 14 / 10
DWK Life Sciences (Kimble)A vacuum-tight seal is created with the open top compression cap and FKM o-ring to allow adjustable immersion of thermometers Cap is suitable for use to 150 °C To use it as a septum port, just replace the o-ring with a PTFE-lined septum Supplied with one FKM o-ring and one 410119…
-
SYNTHWARE Dewar Type Vacuum Traps
Kemtech AmericaVacuum Trap, Dewar Type Capacity: 250, 500, and 1000mL available Stopcock: Glass or Teflon Options available Stopcock Bore: 4mm
-
SYNTHWARE Vacuum Traps, Spherical Joints
Kemtech AmericaVacuum Trap Kit with Spherical Joints. Includes trap body, top adapter, middle adapter, bottom adapter, and clamps. Body OD: 50mm, Body Length: 360mm
-
KF25/NW25 Flange to 3/8" Hose Barb Adapter
Across InternationalOne piece stainless steel KF25/NW25 to 3/8" hose barb adapter for secure vacuum connection. Compatible with the Ai 2.5, 7.2 cfm and Welch 2.3 cfm vacuum pumps, offered by Across International.,/p>
-
SYNTHWARE Two-Piece Vacuum Trap with #15 O-Ring Joint
Kemtech AmericaVacuum Trap with #15 O-ring joint Features 0-12mm high vaccum valve as the shut off. Connection is made via a 57mm O-ring flat flange. Length below flange is 300mm. Steel Clamps sold seperately.
-
KF25 Food Grade Vacuum Angle Flange
Across InternationalKF25/NW25 premium grade 316L stainless steel angle flange with alumimum valve for ultra durability, great for all sorts of high vacuum operations. Grade 316 is the standard molybdenum-bearing grade, second in importance to 304 amongst the austenitic stainless steels. The molybdenum gives 316…
-
Heavy Wall Single Cow Distribution Adapter
Across InternationalAi 24/40 standard taper joint, heavy wall single cow distribution adapter, with one 3/8" hose barb vacuum port.
-
PTFE Thermometer Adapters
Across InternationalThermometer adapter with PTFE body and Viton® O-ring for air tight vacuum work. Features Adapter has a threaded polypropylene screw cap on top with an inside O-ring for depth adjustment of 6-7mm for straight stem thermometers, glass tubing and other items Rotating the extracting…
-
SYNTHWARE Vacuum Trap
Kemtech AmericaFor use with vacuum manifolds having 35/20 socket joints. Please order the pump adapter and socket clamp separately.
-
Synthware Rotary Evaporator Anti-Splash Traps with Fritted Discs
Kemtech AmericaSynthware rotary evporator anti-splash trap with extra coarse fritted disc. Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. the frit reducesfoam from being carryover. With upper outer and lower inner standard taper joints.
-
Synthware Kjeldahl Distilling Trap Adapters
Kemtech AmericaAdapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top outer and lower inner standard taper joints.
-
Chilling Fluid or Vacuum Connectors
Across InternationalGL14x5 GL14 chilling fluid or vacuum connector with sealing gasket, pack of 5. Fits some models of our glass condensers of SolventVap rotary evaporators and glass jacketed reactors. GL18x5 GL18 chilling fluid or vacuum connector with sealing gasket, pack of 5. Fits our SolventVap rotary…
-
Synthware Thermometer Adapters
Kemtech AmericaSynthware thermometer adapter with a 5 degree offset and a serrated hose connection for vacuum. Joints are standard taper.
-
Vapor tube/bump trap adapter is designed to be used with the Büchi® R-200/205 rotary evaporators. This adapter combines a vapor tube adapter and a bump trap. Trap has an extra coarse fritted disc sealed between the lower inner joint and the top flange. Adapters have a 50mm OD top flange…
-
Dual trap assembly for use with AF-0060 or AF-0061 manifolds. Pre-trap (B) is 51mm OD x 250mm long with 28/15 polished socket joints to connect the line shut off adapter (A) to the main trap stopper assembly (C) which has 28/15 o-ring ball joints. The main trap (D) is constructed using a 57mm flat…
-
SYNTHWARE Dual Vacuum Trap Assembly
Kemtech AmericaVacuum Trap Assembly, Dual Joints: #15 O-ring, with high vaccum valves
-
SYNTHWARE Vacuum Traps, Hose Connections
Kemtech AmericaVacuum Trap, Hose Connections Available in multiple sizes with various joint sizes, diameter, length, and inner/side tube size.
-
Side Seal Joints
ChemglassOuter joint having a tubulation sealed at the midpoint of the ground portion, and a corresponding hole drilled in the inner joint permitting venting of the side tube when the inner joint is turned to the proper position. Both of the 19/38 sizes are compatible with Buchi Rotary Evaporators. Part…
-
-
Solid PTFE Joint Stoppers
Across InternationalM ade with solid PTFE for air tight vacuum work, one of the highest quality products you can find in the market.
-
Heavy Wall Short Path Vacuum Jacketed Distillation Heads
Across InternationalThe Ai heavy wall short path distillation head with vacuum jacket. Features Heavy wall for durability Boiling flask and distribution ports Vacuum jacketed Five sets of vigreux Thermo probe port: 14/20 joints Recirculating fluid ports: GL-16 adapters Glass material:…
-
Short Path Distillation Head
United Scientific SuppliesShort Path Distillation Head with 24/40 flask joints and 10/30 thermometer port. Distillation head is manufactured from high quality 3.3 borosilicate glass and features a condenser coil and three 1/4" hose nozzles, two for condenser and one for vacuum.
-
SYNTHWARE Cylindrical Vacuum Traps
Kemtech AmericaVacuum Trap, Cylindrical Available in multiple sizes with various joint sizes, diameter, length, and inner/side tube size.
-
Synthware Vacuum Take-Off Adapters
Kemtech AmericaSynthware vacuum take-off adapter with drip tip. The upper outer and lower inner standard taper joints are the same size.
-
Synthware Distillation Adapters
Kemtech AmericaSynthware distillation adapter with a 10/18 standard taper outer joint for a 76mm immersion thermometer. The adapter has a standard taper top outer joint and inner joints for the bottom and side.
-
SYNTHWARE Micro Dewar Vacuum Traps
Kemtech AmericaVacuum Trap, Dewar, Micro Reservoir Capacity: 100mL Stopcock: Glass or Teflon options available 2mm Stopcock Bore