Unique seal system allows use as solid or one-, two- or three-hold closures Simplifies stock room inventory Molded of soft, resilient, white natural rubber Seals vacuum-tested to 760 mm Hg Autoclavable, with good shelf life. Sizes #3 & #4 have two holes; #5 - #10 have the (3)…

Sleeve Type Septum stopper made from natural white rubber for use with 5mm NMR tubes.

A back-seal, solid plug for sealing coulmn ends. Supplied with one FETFE O-Ring.

Uses include outgassing NMR tubes, pressure venting or adding reactants via syringe. Hollow, plug-type stopper fits into the neck of the glassware apparatus Sleeve extension fits over the neck for a secure seal Diaphragm can be punctured with a syringe needle Series 774261 may be…

Hungate stopper only for use with Hungate tubes. Specifications: Black Butyl Rubber Size: 13MM 250 each per case Dimensions: 13mm at top, to 10mm x 5mm Thick For Use With Hungate Tube:  2047-00125  

Similar to 8771R10 series, but in standard taper joint sizes Conforms to ASTM Standard E 675 Use with boiling and distilling flasks

Test tube with interchangeable stopper; 24/40 stopper is hollow, other two solid.

Hollow stopper with closed bottom

Set comes with 8 sizes. Stoppers are to be used with Buchner and Fritted glass funnels.

These stoppers are used as an accessory for microscale threaded Standard Taper 14/10 kits. Pennyhead stopper sizes 10/18 through 19/22 are solid borosilicate glass Sizes 24/25 and larger are hollow borosilicate glass Manufactured from 33 expansion, low extractable borosilicate glass…

These blue and white No. 13 PYREX® stoppers are made from linear high-density polyethylene and have closed bottoms to conform to Standard Taper stopper dimensions. The three rings on the plug provide an efficient seal. This improved design fully protects the neck in the event of accidental…

A laboratory rubber stopper is mainly used in chemical laboratory in combination with flasks and test tub. Specifications: Material: Rubber Flask Closure

Yellow and blue closed-bottom linear high-density polyethylene stopper to fit in the ground glass neck Enlarged flange on stopper is designed to protect the glass if tipped over Size: 13 Case of 6

Standard Grade Size No. 000 is 18 mm long; sizes No. 00 to No. 13 are 25 mm long. Sizes No. 13 1/2, 14 and 15 are 35 mm, 36 mm and 39 mm respectively.

Well-known as the best quality rubber turn-over closure with serrated stopper, Suba-Seal brand is available exclusively from Sigma-Aldrich. Ideal for air and moisture-sensitive chemistry procedures. After piercing with non-coring needle, rubber closes puncture, providing air and moisture tight seal…

Solid stopper with closed bottom.

Bromobutyl rubber compound with a high level of chemical purity Straight Plugs and Lyophilization Stoppers (2-leg, 3-Leg and Igloo) are available All Ultra Pure Stoppers are autoclavable Ultra Pure Straight Plug Stoppers are made from a bromobutyl rubber compound containing the…

A laboratory rubber stopper is mainly used in chemical laboratory in combination with flasks and test tub. Specifications: Material: Rubber Flask Closure Size: 0 Top Diameter: 17mm Bottom Diameter: 13.5mm Length 25mm

Designed for use with Millipore stainless steel vacuum filter holders Stopper Size: No. 8 Hole I.D.: 9.5mm (3/8 in.) Silicone rubber construction

This precision-engineered adapter may be cut with a fine-tooth saw or sharp knife into various adapters, such as individual bushings, stirrer bearings, thermometer and gas inlet tube supports, drip-tips, funnels, trap connectors for tubing, etc. Forms a continuous standard taper inside and…

RS-2H-C 1 pound package of assorted 2 hole rubber stoppers. Sizes and quantities are as follows: Size 2: 3 each Size 3: 3 each Size 4: 3 each Size 5: 3 each Size 6: 3 each Size 7: 3 each Size 8: 3 each

Silicone stoppers are particularly useful due to their inert and nonreactive nature. It will not impair the growth of tissue cultures and resistant to most chemical acids and solvents. Stoppers can be steam sterilized at 15 lbs. pressure. Broad working temperature range of –62 to 232°C…

Top Stoppers for Incubation Flasks. Rubber stoppers for flask top and sidearm provide a secure double seal Top stopper has off-center hole for insertion of center well Fits both 10 and 25 mL flasks

With a patented Glas-Col Snorkel Stopper, you'll never again have to take time to open the stopcock and relieve pressure when vigorously shaking a separatory funnel, because our Snorkel Stopper does the task automatically. If you use a Glas-Col shaker, you can simply load the funnels onto it…

Manufactured from Blue Chlorobutyl. The septum stopper can withstand autoclaving 160 degree Celsius at normal autoclaving times 12-20 minutes. Specifications: Material: Blue Chlorbutyl Autoclaving: No Higher Than 160 Degree Celsius Size: 20mm Case Quantity: 100  

PTFE stopper is similar to CG-3002-L but with the addition of one female NPT port in the center for connection of compression fittings or pressure/vacuum gauges. PTFE stopper has an extraction nut permitting easy removal of the stopper from the glass outer joint.

Complete Coat Stoppers are completely coated with a fluorinated polymer that has barrier properties similar to PTFE. The fluorinated polymer coating is the only material that comes in contact with the sample. As a result, chemical reactions due to unwanted interference with the rubber itself are…

Sleeve stopper septa are manufactured from pure natural rubber for excellent resealability when used for cannulation techniques or from FKM rubber for high chemical resistance. Natural rubber septa are available in red and white colors and a soft rubber formulation that contains no fillers or…

Three twist-off seals permit easy conversion from a solid to a one, two, or three-hole stopper. Soft, resilient, natural rubber demonstrates exceptional aging characteristics and withstands repeated autoclaving. Autoclavable at 250°F for 30 minutes under water or steam conditions only (not…

Gas tight tube designed for maintaining anaerobic conditions. Useful for studies involving methane-producing bacteria. Includes gas impermeable blue butyl rubber septum type stopper. Tube is made of Type 1 Class B Borosilicate glass. Specifications: Type 1 Class B Borosilicate Glass Blue…

Natural red rubber or gray chlorobutyl/45 material 7 x 13 or 13 x 20 mm sizes

Ultra Pure Lyophilization Stoppers are made from a bromobutyl rubber compound containing the highest level of chemical purity. These stoppers demonstrate a very low level of moisture absorption and are ideal for most lyophilization applications. They are compatible with Water for Injection (WFI)…