Kemtech America Lab Glassware
-
Synthware Vacuum Adapters with 1:5 Teflon® Stopcocks
Kemtech AmericaSynthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper inner joint. The PTFE stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.
-
Synthware Inlet Adapters with Hose Connection
Kemtech AmericaAdapter has a Nylon compression cap and a Viton o-ring to form a vacuum tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. The 8mm hose connection can be used for N2/Ar introduction or vacuum. Supplied with one Nylon cap and one Viton o-ring.
-
SYNTHWARE Kugelrohr Distilling Bulbs
Kemtech AmericaKugelrohr Distilling Bulb Capacity: 5, 10, 15, 25 or 50mL available Joints: 14/20, Bulb O.D.: 25, 31, 35, 42 or 48mm available Overall Height: 80, 85, 90, 98 or 105mm available Used in distillation of very small amount of distillate at lower temperature with high efficiency.
-
Synthware Reducing Adapters
Kemtech AmericaSynthware reducing adapters are used for connecting dissimilar standard taper joint sizes. The lower inner joint is larger in size than the top outer joint.
-
-
SYNTHWARE Distillation Receiving Set
Kemtech AmericaComes with Synthware Distilling Adapter (Joints: 14/20 or 19/22) and Cow Receivers (Joints: 14/20 or 19/22). Designed without hose connection to be used with D10 distillation apparatus. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**
-
Synthware Vacuum Take-Off Adapters with Glass Stopcocks
Kemtech AmericaSynthware vacuum adapter with 2mm straight bore glass stopcock on the hose connection.The upper outer and lower inner standard taper joints are the same size.
-
Synthware Claisen Adapters, Modified
Kemtech AmericaIt is modified with an additional side arm at 45 degrees to the vertical outer joint. All joints are the same size.
-
SYNTHWARE Y-Shaped Connecting Tubes
Kemtech AmericaConnecting Tube, Y-shaped, Synthware, Tubing OD: 8mm.
-
Synthware Vacuum Filtration Adapters
Kemtech AmericaUsed with plain stem Buchner funnels and pluro-stopper. Hose connector has an O.D. of 10mm at the largest serration. Joint is a standard taper inner joint. Pluro-stoppers are not included.
-
Synthware Inlet Adapters with Extended Length Lower Tubes
Kemtech AmericaSynthware inlet adapter with extended length lower tube. Allows for the introduction of reactants below the interior surface. Tube extends 153mm (6 inches) below the joint. Tubing has the same O.D. on both ends of the joint.
-
SYNTHWARE Solvent Distilling Heads
Kemtech AmericaSolvent Distilling Head Capacity: 250, 500, and 1000mL available Joints: 14/20 and 24/40 available Sampling Port: 14/20. Heads feature a 2mm double oblique stopcock bore
-
Synthware Inlet Adapters
Kemtech AmericaSynthware inlet adapter with a standard taper inner joint. Design allows introduction of reactants below the surface. The serrated hose connections have an O.D. of 10 mm.
-
Synthware Long Stem Inlet Adapters
Kemtech AmericaSynthware long stem inlet adapter. With standard taper top outer joint and lower inner joint with sealed in lower tube extending below the inner joint.
-
Synthware Vacuum Adapters with Glass Stopcocks, 90°
Kemtech AmericaSynthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper inner joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.
-
Synthware Vacuum/Inert Gas Adapters with Ball Joint
Kemtech AmericaAllows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection is at a 90 degree angle to the spherical ball joint.
-
Synthware Inlet Adapters
Kemtech AmericaFor use with gas inlet tubes or plain stem thermometers. Supplied with one holed rubber adapter.
-
Synthware Vacuum Take-Off Adapters, Short Stem
Kemtech AmericaSynthware vacuum take-off adapter with drip tip. For use in vacuum distillation. Adapter is bent at 105 degrees. Serrated hose connection is attached to vacuum source. With standard taper top outer joint and lower inner joint of the same size.
-
Synthware Distillation Adapters, Vigreux
Kemtech AmericaSynthware Vigreux distillation connecting adapter. Indenstations in lower section improve liquid/vapor contact. The standard taper top outer joint accomodates a 76mm immersion thermometer. Bottom and side joints are standard taper inner joints.
-
Synthware Flushing Adapters
Kemtech AmericaSynthware flushing adapter is used to flush and fill attached vessels with an inert gas to provide protective storage. A ballon is connected to the top hose connection. An inert gas is connected to the side hose connection. The ballon can be expanded with inert gas at the same time as the vessel or…
-
SYNTHWARE Adapter with #15 O-Ring Joint to Inner Joint
Kemtech AmericaAdapter, #15 O-ring joint to 14/20, 19/22 or 24/40 inner joint
-
Synthware Inlet/Thermometer Adapters
Kemtech AmericaAdapter has a Nylon compression cap and a Viton o-ring to form a vacumm tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. To use it as a syringe port, simply replace the o-ring with a PTFE-lined septum. Supplied with one Nylon cap and one Viton o-ring.
-
SYNTHWARE Sublimators
Kemtech AmericaSublimator, Two Piece, Synthware, Various sizes are available. O-Ring Size: 217, 226, or 229, Clamp Size: 35, 65, or 75 available.
-
Synthware Kjeldahl Distilling Trap Adapters
Kemtech AmericaAdapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top outer and lower inner standard taper joints.
-
Synthware Vacuum Adapters with PTFE Stopcocks
Kemtech AmericaSynthware vacuum adapter with a serrated hose connection 180 degrees to the standard taper inner joint. The PTFE stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.
-
SYNTHWARE Vacuum Takeoff Adapter
Kemtech AmericaVacuum Takeoff Adapter, Microscale, Synthware, Joint: 14/10, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.
-
Synthware Rotary Evaporator Traps
Kemtech AmericaSynthware rotary evaporator trap. Anti-climb design. Trap provides expanded volume for reactions that have a tendency to foam excessively. The inner vapor tube is sealed to the top of the trap to prevent entry into the condenser.
-
Synthware Rotary Evaporator Anti-Splash Traps with Fritted Discs
Kemtech AmericaSynthware rotary evporator anti-splash trap with extra coarse fritted disc. Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. the frit reducesfoam from being carryover. With upper outer and lower inner standard taper joints.
-
Mineral Oil Bubbler Oil Adapters
Kemtech AmericaSynthware adapter with oil bubbler. With standard taper inner joint. Horizontal design allows for in line connection for apparatus purging.
-
SYNTHWARE Glass Check Valves
Kemtech AmericaCheck Valve, All Glass, Synthware, Hose Connections OD: 8mm, with ground seat for liquid seal.
-
SYNTHWARE Shortpath Distilling Head for Volatile Distillants
Kemtech AmericaWith the condenser being a combination of a cold coil and Leibig. Top outer joint is a 10/18 for use with a 50mm immersion thermometer. With Vigreux Indentations.
-
SYNTHWARE Distillation Adapter
Kemtech AmericaDistillation Adapter, Microscale, Synthware, Joints: 14/10, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.