Oil Bubbler

Compare Tool

Select up to 3 products

Oil Bubbler
1 - 15 of 15
Sort
View
Show
  • Mineral Oil Bubbler, Body OD: 26mm,Overall Height: 185mm OR 500mm, Hose Connection: 10mm **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

  • SYNTHWARE Bubbler

    Kemtech America

    With small ball joints to prevent mineral oil being sucked back under sudden negative pressure in the system.

  • …gas enters bubbler through hose connection (A) and exits thru connection (B) which is connected to manifold. The large capacity of the main chamber (C) allows for rapid purging with check valve protection of the inert gas source (D). The constriction of the large chamber prevents oil from being…

  • Used to make a vent to the atmosphere. May also be used with mercury when adequate ventilation is available. Reservoir head prevents oil from being sucked back into the system. With 8mm O.D. tubing connections. Volume approximately 40mL below side arm.

  • With completely adjustable 7mm inner tube. Tube has a pulled tip and is secured by a #7 Ace- Thred. Volume approximately 40mL. Tapered bottom of vessel allows for use with small volumes. Nylon bushing supplied with FETFE O-Ring. Available modified with #7 Ace-Threds on inlet/outlet for use with…

  • …check valve bubbler keeps oil and air from being drawn into a reaction system when negative pressure is developed. Bubbler has two 1/2" swagelock type fittings on top permitting one side to be connected to the nitrogen source and one side to the reaction system. The bubbler is filled with oil

  • …a vent to the atmosphere. Reservoir head prevents oil from being sucked back into the system. Standard taper inner joint is for use in single or multi-neck flasks. Hose connection has a 9mm OD middle serration. The 24/40 jointed bubbler is available in two sizes; the larger for use in vessels…

  • Used to monitor gas flow to reactions while providing a vent to the atmosphere. Reservoir head prevents oil from being sucked back into the system. Volume below the sidearm is approx 40mL. Bubbler has an 8mm OD top and side tubulations.

  • …reactions while providing a vent to the atmosphere. Bubbler has a "T" connection at the top to allow it to be mounted in-line while the reservoir head prevents oil from being sucked back into the system. Volume below the sidearm is approx 40mL. Bubbler has 8mm OD top and side tubulations.

  • Bubbler has an adjustable inner tube with a #9 Chem-Thread. Taper at bottom of reservoir allows for use of a minimal amount of oil. Complete bubbler consists of the lower reservoir, adjustable inner tube, compression cap and Viton o-ring.

  • Bubbler has an integral valve to control the flow of inert gas into the system. Bubbler requires a minimal amount of oil due to the inner tube being within 5mm of the bottom. Both sidearms are 9mm OD for use with 3/8" Cajon®; fittings. Overall height is approx. 220mm.

  • Similar to the CG-4440 vacuum manifold, but with BOTH ENDS OF INERT GAS LINE OPEN to permit connection to the gas source and an oil bubbler. Hose connections have a 10mm small serration and a 11mm large serration.

  • Similar in design to AF-0513 but with two oil reservoirs. Bubbler is approx 125mm W x 135mm H. Hose connections are 9mm OD at the middle serration.

  • Synthware adapter with oil bubbler. With standard taper inner joint. Horizontal design allows for in line connection for apparatus purging.

  • Bubbler Mineral Oil

    DWK Life Sciences (Kimble)

    Used with mineral oil to observe gaseous addition to reactions. May be used to vent a reaction mixture to the atmosphere. Tubing connections are 8 mm O.D. and may be used with 179730-0808 or 179920-0808 to join multiple bubblers if necessary.

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.