Ace Glass Lab Glassware
-
Filter Stick, Glassblower Parts
Ace GlassPorous fritted glass filter stick used to fabricate gas dispersion tubes. Measures 10mm O.D. x 20mm long, hollow at one end. Packed 6 per package. Minimum order, one package.
-
Ace-Threds and Ace-Thred and joints
Ace GlassWith Ace-Threds or Ace-Thred and joints. Accepts a single 5mm or 10mm O.D. NMR Tube. Solvent reservoir capacity is 55mL. All threaded versions have a filter flask with a #15 Ace-Thred at top and O-Ring and #11 Ace-Thred side port with a removable Ace-Safe hose connection. Threaded-jointed version…
-
Splitter Distillation, Reflux
Ace GlassReflux distillation splitter adapter for all sizes of reactors. Standard taper inner joint bottom and reinforced outer joint top. Straight path splitter intended for use with 90 degree vertical joints. 0-10mm side valve with precision ground swagelok v
-
-
Adapter, Bushing
Ace GlassBushing type adapter for standard taper joints. Smaller outer or female joint is within the larger male joint.
-
Immersion Well, Photochemical, Quartz
Ace GlassDouble-walled, quartz Immersion Well for use with 7825-30, -32, -34, and -36 lamps. With inlet and outlet tubes for cooling or modified with a 4.8mm I.D. PTFE tube attached to a glass tube and secured with a #7 Ace-Thred bushing. Inlet tube extends down the annular space to insure flow of coolant…
-
Pressure Vessels, Tubes & Bottles
Ace GlassAce Glass pressure tubes and bottles are the premier glass pressure vessels in the industry. Flat-bottomed bottles are rated at 60psi at room temperature while our tubes are rated at 150psi at as much as 120 degrees C. Due to varying conditions, Ace cannot guarantee glass vessels from breaking…
-
Beaded Process Pipe
Ace GlassAll pipe is available from stock in lengths shown; special lengths available at slightly higher cost.
-
Still, Solvent Recovery
Ace GlassWhen attached to the top of Snyder Column, unit is designed to recover solvent normally lost during Kuderna-Danish Evaporative Concentrations. PTFE stopcock (1:5, 2mm bore) provides option for total reflux or takeoff. #7 Ace-Thred on side arm accepts tubing 6 - 7mm O.D. 5029-10 Nylon bushing and…
-
-
Head, Hickman Still
Ace GlassMicroscale Hickman Still Head used to carry out micro sample fractional distillations. With outer joint at top externally threaded to allow a O-RING-CAP-SEAL connection with mating male joint and inner joint at bottom. Supplied with cap, O-Ring and septum. Available with ex-ternally threaded outer…
-
Joints, Inner Member
Ace GlassStandard taper joint with reduced tube at both ends. Length of tube below joint is 100mm.
-
Cylindrical vessel with a 2mm bore PTFE stopcock, GL thread at top, Ace-Thred at bottom that accepts a PTFE adapter with removable Por. C glass filter disc and a PTFE shut-off valve. PTFE adapter has a front type seal using a CAPFE O-Ring to make a compression seal in the Ace-Thred on Vessel. Other…
-
Tube, Connecting, 90 degree
Ace GlassConnecting tube, 90 degree angle, with ends having constriction to hold rubber tubing securely. Sold in packages of 6.
-
-
With standard taper 24/40 joint and outlet tube bent at 75 degree angle.
-
Distilling Receiver
Ace GlassAn excellent all-purpose receiver for general distillation work. Equipped with a complete stopcock manifold to allow contents of the receiver to be removed to a single receiving flask without disturbing the vacuum of the system. Stopcocks are 4 mm bore.Tubing connections are 10mm O.D. olive type.
-
Adapter, Bleed
Ace GlassWith drawn capillary tip for the introduction of gases below the liquid surface. Outside diameter is 7 mm. Length approximately 320mm (12-1/2"). For use with #7 Ace-Thred. Hose connection on bent adapter is size A.
-
Adapter, Kjeidahl Trap
Ace GlassWith 24/40 standard taper joints. Distance between center of joints is approximately 200mm.
-
PTFE adapter, precision made, for use when making NPT thread connectors to Ace-Threds. One end designed to make leaktight seal with Ace-Thred without use of O-Rings, other end accepts NPT male thread. Can be used when making connection at top of rapid prep columns or rigid connection between…
-
Vapor Duct Tube, For Rotary Evaporators
Ace GlassReplacement vapor duct tube for Buchi rotary evaporators. The 45mm length fits V assemblies and the 160mm length fits A assemblies. End joints are available in [ST] 29/32, [ST] 24/40, or [ST] 29/42 inner. The middle joint is tooled to fit the specific rotary evaporator for which it was designed.…
-
Schlenk filter tube with an integral glass filter disc at the tube's mid-line and featuring two sidearms with either a glass stopcock or a 0-3 inlet valve. Paired top and bottom inner joints.
-
Adapter, Bottom Drip, Luer
Ace GlassLuer, Bottom drip Adapter with or without flow regulator valve for use with ACE threaded columns. Shallow taper at upper end minimizes mixing below the packing support. Supplied with one FETFE O-Ring and one replaceable polyethylene packing support. For replacement packing support, either…
-
Distilling Receiver
Ace GlassCalibrated to contain. Supplied in 10mL capacity with 0.2mL subdivisions.
-
Reaction Flask Head
Ace GlassConical 4" neck for use with 6475, 6476, 6477, 6479, 6480, 6481, 6491, 6492, 6497, 6498 and 9656 ACE Reaction Flasks. Supplied with three outer joints. Use 6496 Clamp for securing to flasks.
-
Distilling Head
Ace GlassWith finger type condenser and 0-3 mm PTFE stopcock plug with PTFE ring seals for reflux control. The seals prevent O-Ring exposure to corrosive liquids and are backed up by a FETFE O-Ring. Thermometer joint is 10/30, all others are 14/20.
-
Adapter with Ace-Thred
Ace GlassAdapter with ground joint at bottom and either a #11, #15, #25 or #36 Ace-Thred at top.,/p>
-
Firestone splash guard adapter with medium length joints that will accept full length joints. Internal porosity A (147-174 micron) fritted disc that assures no carry-over in the event of pot splash-up. Overall length is kept to a minimum to positively
-
Tube, Connecting
Ace GlassStraight reducing connector tube, with ends of different size. Sold in packages of 6.
-
Solvent Collector and Dispenser
Ace GlassUsed for collection and long-term storage of solvents. With standard taper 14/20 outer joint and 2 mm bore PTFE stopcock at top, double oblique 2 mm bore PTFE stopcock and standard taper 14/35 joint at bottom. Capacity is 250mL.
-
Schlenck Filter Tube, NO-AIR
Ace GlassSchlenk filter tube with an integral glass filter disc at the tube's mid-line and featuring inner joints at top and bottom.
-
Distilling Receiver
Ace GlassFor operation other than at atmospheric pressure. Vacuum is applied to the side arm with the T-bore stopcock. The secondary receiver is vented by means of the lower stopcock. The capacity from the bottom of the drip to the stopcock is 2.5mL.