Glass, Ace Glass, Supplies
-
Septa, Rubber
Ace GlassSepta tops are flanged with a sleeve-like extension that folds down over the vessel's neck. Punctured diaphragm re-seals after syringe is withdrawn. Septa are supplied in a variety of sizes, red, white or grey rubber.
-
Adapter, Sublimation
Ace GlassUnique device for carrying out sublimation directly in round bottom reaction flask; simply remove condenser, stirrer, etc. from joint, insert sublimation adapter and begin. Coolant connection at top and side vacuum connection are 9.5 mm (3/8") O.D. Vacuum connection is controlled by 1:5 PTFE 2 mm…
-
Pressure Vessels, Tubes & Bottles
Ace GlassAce Glass pressure tubes and bottles are the premier glass pressure vessels in the industry. Flat-bottomed bottles are rated at 60psi at room temperature while our tubes are rated at 150psi at as much as 120 degrees C. Due to varying conditions, Ace cannot guarantee glass vessels from breaking…
-
Hose Connections, Large
Ace GlassRing-style hose connections for use on large soxhlet condensors, etc. With flare end. Sold in shelf-packs of 12 each.
-
Distilling Head
Ace GlassWith finger type condenser and 0-3 mm PTFE stopcock plug with PTFE ring seals for reflux control. The seals prevent O-Ring exposure to corrosive liquids and are backed up by a FETFE O-Ring. Thermometer joint is 10/30, all others are 14/20.
-
-
Interchangeable ground joint bearing with top lubricant well for use with our precision ground stirring shafts (8068,8070,8071,8073, 9532,9533). Recommended top stirring speed with our 8117 Stir-Lube is 1500 rpm.
-
Hose Connections, Direct Seal
Ace GlassFour ring connector, (code -03 has three rings), is tooled with flare and exposed for direct sealing to apparatus. Tooled on each end of tubing with approximately 5-6" between connectors. Priced per dozen connectors (i.e., six doubles).
-
Adapter, Connecting Hose
Ace GlassWith standard taper outer or spherical socket joint at one end and a hose connection at the other end.
-
-
Glass standard taper joint adapters featuring a drip tip and a vertical ground glass tube sidearm. The sidearm is used to make tube compression fitting connection to a wide variety of flexible and rigid tubing using our 12709,12711,12715 & 12716 product families of fittings.
-
Adapter, Vacuum Take-off, Short Stem
Ace GlassOuter joint at angle of 105 degree. Hose connection opposite top joint. Stem below joint, 30mm.
-
Adapter, Ace-Thred to o-ring joint
Ace GlassAdapter, 15mm o-ring joint to Ace-Thred, fetfe o-ring included.
-
Adapter, Twin, Ace-Thred
Ace GlassTwin adapter features two Ace-Thred top openings and a standard taper inner joint bottom. With the supplied nylon bushings, two tubes or a thermometer and bleed tube can be inserted through the same joint. The 24/25 medium length joint is compatible wi
-
Thermometer Well, with Joint
Ace GlassFor reaction flasks, can be used with either cylindrical or spherical type. With 14/35 joint. Length measurement (A) is distance below joint to bottom of tube.
-
-
Joints, Inner Member
Ace GlassStandard taper joint with reduced tube at both ends. Length of tube below joint is 100mm.
-
Same as 7854-25 Immersion Well except that the 60/40 inner joint is PTFE-Clad. Double-walled, quartz Well with inlet and outlet tubes for cooling. Small diameter inlet tube extends down the annular space to ensure flow of coolant from bottom of well upward to inlet.
-
Flask, Round Bottom, with Threaded Joint
Ace GlassMicroscale, single-neck, round-bottom reaction flask with outer joint externally threaded to allow an O-RING-CAP-SEAL connection with mating male joint. This type connection eliminates the need for clamps while offering the positive leak-tight seal of ground glass. Supplied with threaded cap with…
-
With the joint at bottom, either a #7, #11, #15 Ace-Thred at top and serrated hose connection.
-
Adapter, Bleed
Ace GlassWith drawn capillary tip for the introduction of gases below the liquid surface. Outside diameter is 7 mm. Length approximately 320mm (12-1/2"). For use with #7 Ace-Thred. Hose connection on bent adapter is size A.
-
Joints, Inner Member, Microscale
Ace GlassStandard taper inner ground joints used in fabrication of ACE Microscale Glassware. Use with 7609 outer member. Codes -11, -12 and -13 have drip tip.
-
Adapter Connecting, NO-AIR
Ace GlassY shaped, 3-way adpater. One outer joint, two inner standard taper joints. Great for adapting flasks and other Schlenk line components. All three joints are the same size.
-
Adapter, 15mm o-ring joint to standard taper inner joint, porosity B (70-100 micron) frit, fetfe o-ring included.
-
Adapter, O-Ring Joint to Hose Connection
Ace GlassAdapter, o-ring joint to size E hose connection, fits 3/8"-7/16" id tubing, fetfe o-ring included
-
Adapter, Gas Inlet
Ace GlassWith 24/40 standard taper inner and outer joints and side hose connection size D.
-
Distillation Apparatus, Short Path
Ace GlassDesigned for small quantities where holdup between flask and receiver must be minimized, but where it is also desired to measure vapor temperature with the accuracy of larger setups. Still body is available with or without vacuum jacket and with vigreu
-
Adapter, Connecting Hose
Ace GlassAdapter with bent hose connection top and either a standard taper or ball joint inner bottom. Codes -110,-112,-114 have an integral porosity A fritted disc.
-
Reaction Flask Head
Ace GlassConical 4" neck for use with 6475, 6476, 6477, 6479, 6480, 6481, 6491, 6492, 6497, 6498 and 9656 ACE Reaction Flasks. Supplied with three socket joints. Use 6496 Clamp for securing to flasks
-
Adapter, Bushing
Ace GlassBushing type adapter for standard taper joints. Smaller outer or female joint is within the larger male joint.
-
-
Mineral Oil Bubbler
Ace GlassUsed to make a vent to the atmosphere. May also be used with mercury when adequate ventilation is available. Reservoir head prevents oil from being sucked back into the system. With 8mm O.D. tubing connections. Volume approximately 40mL below side arm.