Bent Adapter

Compare Tool

Select up to 3 products

Bent Adapter
1 - 32 of 32
Sort
View
Show
  • Adapter is bent 105 degrees. The top outer and lower inner standard taper joints are the same size.

  • 105° Bent Distillation Adapters

    DWK Life Sciences (Kimble)

    Bent 105 degree distillation adapters. Standard Taper inner joint at the bottom and Standard Taper outer joint at the top Joints are the same size Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements …

  • Adapter is constructed completely of PTFE and is ideal for eliminating stress between standard joints. Can be bent up to 120º. Top outer and lower inner are of the same size.

  • …syringe needle does not pierce the septa, there is no debris and ghost peaks are greatly reduced. The MicroSeal septa also reduces the incidence of bent syringe needles and liner contamination. Usable in either manual or autosampler applications, this septa can improve your productivity and run…

  • …complete with one AF-0070-03 #15 o-ring joint to 3/4" straight tubing adapter and one AF-0070-20 #15 o-ring joint to 3/4” bent tubing for connection to heavy wall flexible vacuum tubing. Other sizes of the AF-0070 adapters are available to fit different ID vacuum tubing.Overall dimensions…

  • 105° Bent Distillation Adapters

    DWK Life Sciences (Kimble)

    Barbed hose connection Standard Taper inner joint with drip tip at the bottom and Standard Taper outer joint at the top Joints are the same size Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

  • Glass Vacuum Adapters

    United Scientific Supplies

    Vacuum adapters have 24/40 joints. Bent adapter has a 105° angle between the top outer joint and bottom inner joint. Straight adapter has a top outer joint and bottom inner joint. Both adapters have 24/40 joints and include a 3/8" hose connector.

  • Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection has an O.D. of 10mm at the largest serration and is bent downward at a 90º angle to the inner joint.

  • Synthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints. 

  • 75° Bent Distillation Adapters

    DWK Life Sciences (Kimble)

    Ideal for use as a stillhead adapter. With Standard Taper inner joints at each end Both joints are of the same size Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

  • With standard taper 24/40 joint and 8mm O.D. outlet tube bent at 75 degree angle.

  • With outer Standard Taper joint at the top and an inner-sealed through drip-tip joint at the bottom Bent at 105° angle The serrated sidearm is 10 mm O.D. drip-tip at the bottom extends about 20 mm below the lower end of the joint

  • …hub 304 stainless steel needle Standard 2” length Use with Luer Tip and Luer Lock syringes sold without needle or for Luer adapters. Nickel-plated brass or Kel-F (CTFE) hubs fit both male and female Luer connectors.They allow quick change of needle and use of different gauge…

  • With standard taper joints, one 14/20 outer and one 14/35 inner or one 24/25 outer and one 24/40 inner.

  • Flask Adapters

    Labconco

    …and B75, but bent at 135° (45° from vertical). Reducing Type Adapters (5119B85 and B87): Connects flasks with 3/4” mouth to 1/2” valves or flasks with 1/2” mouth to 3/4” valves Of borosilicate glass 5119B85 adapter is straight; 5119B87 adapter is bent at 135° angle…

  • Adapter, Bleed

    Ace Glass

    With drawn capillary tip for the introduction of gases below the liquid surface. Outside diameter is 7 mm. Length approximately 320mm (12-1/2"). For use with #7 Ace-Thred. Hose connection on bent adapter is size A.

  • Synthware distillation adapter bent at 75 degrees. Both ends are standard taper inner joints and are the same size.

  • Distillation adapter with a top outer standard taper joint. Tapered delivery tube is bent at a 105º angle to the outer joint and extends into open receivers.

  • Adapter with bent hose connection top and standard taper inner bottom joint.

  • Stopcock adapter featuring either a bent or straight hose connection and a glass plug.

  • Adapter with bent hose connection top and either a standard taper or ball joint inner bottom. Codes -110,-112,-114 have an integral porosity A fritted disc.

  • Stopcock adapter featuring either a bent or straight hose connection and a PTFE plug.

  • Radial style distillation receiver allows four flasks to be progressively filled. Upper vacuum adapter is bent at a 105° angle.

  • Stopcock adapter featuring either a bent or straight hose connection and a glass or PTFE plug. See Ace 8223 for replacement glass plug and Ace 8224-04 for PTFE plug.

  • Synthware vacuum take-off adapter with drip tip. For use in vacuum distillation. Adapter is bent at 105 degrees. Serrated hose connection is attached to vacuum source. With standard taper top outer joint and lower inner joint of the same size.

  • With standard taper top outer and lower inner joints with sealed in drip tip. Adapter is bent at a 105° angle for use in vacuum distillation. Serrated hose connection has an O.D. of 10mm at the largest serration for connection to vacuum source.

  • Radial style distillation receiver allows four flasks to be progressively filled. Upper vacuum adapter is bent at a 105º angle. Complete item consists of a vacuum adapter, distribution adapter, four of the listed size flasks with hooks and ten CG-110 stainless steel springs.

  • With standard taper 24/40 joint and outlet tube bent at 75 degree angle.

  • Allows introduction of reactants below the interior surface. Hose connection has a O.D. of 10mm at the largest serration and is bent downward at a 90º angle to the inner joint.

  • …valve with bent arms to minimize hold up of fluids that would occur in conventional valves. Designed with a precision external thread for fine control. VALVES, 3-WAY, EXPOSED O-RING TIP, Hi-vac valve with three way configuration for use in construction of manifolds, adapters, etc. VALVES,…

  • PTFE Valves

    Chemglass

    …Hi-vac valve with bent arms to minimize hold up of fluids that would occur in conventional valves. Designed with a precision external thread for fine control. VALVES, 3-WAY, PTFE TIP, Hi-vac valve with three way configuration for use in construction of manifolds, adapters, etc. VALVES, 1-ARM,…

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.