High efficiency air condenser is a waterless glass condenser that requires no cooling water for operation. The glass bellows design provides a high surface area air condenser which is very effective. Performance of the high efficiency air condenser is equivalent to a Liebig type condenser…

These PYREX® condensers have a high surface area per unit length of the 200mm long jacket with a 19/38 Standard Taper outer joint at the top and a plain drip tip at the bottom. They are primarily used in distillation assemblies Condenser tubulations are approximately 10mm O.D.

This PYREX® Friedrichs type condenser affords very efficient operation. The helical inner tube fits closely within the jacket. The vapor tube is sealed to the jacket at an angle of 75° and has an outer 24/40 Standard Taper joint.

High efficiency coil condenser especially suited for vacuum applications. Coil length is 70mm. With 14/10 inner and outer joints; outer joint is externally threaded to allow an O-RING-CAP-SEAL connection with mating inner joint. Supplied with cap and O-Ring.

Coil style reflux condenser with tightly wrapped coil providing maximum cooling. Excellent for use with high vapor pressure solvents. Condenser has a top outer standard taper joint and lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

Coil style reflux condenser with a larger diameter jacket and coil, thereby providing maximum cooling capacity, while being shorter in length. Hose connections are on the bottom of the condenser which makes it easier to connect hose/tubing. Connections are GL14 polypropylene hose barbs and screw…

Microscale, water-jacketed condenser used in reflux experiments. With outer joint at top externally threaded to allow an O-RING-CAP-SEAL connection with mating male joints and inner joint at bottom, with drip tip. I.D. of inner tube on code -23 is sufficiently large enough to accept regular size…

Condenser for use in refluxing from 1 to 20mL of solvent in flasks having a capacity of 5 to 50mL. Minimal surface area provides for better yields while providing adequate cooling. The additional hose connection is provided to allow introduction of an inert gas such as nitrogen. Top hose connection…

Air Cooled Remote Condensers Operate in wide outdoor temperature range from -20ºF to 120ºF. Single or double circuit for single or double unit installations. Heavy gauge galvanized steel for corrosion resistance. Thermally protected fan motors. PVC coated steel fan guards. …

Bulb type, approximately one bulb per 50mm, with water cooled standard taper 24/40 inner and outer joint at bottom and top.

With spiral condensing tube having both inlet and outlet connections at top, on same side. With joints. Length between joints is approximately 80-90 mm longer than the stated coil length. Available with PTFE clad bottom joint.

This specially designed PTFE condenser jacket is a replacement part for the PTFE Cyanide Distilling Apparatus (Thomas No. 0320A91)

With top joint jacketed for water cooling. Jacket length measured from bottom of top joint.

Coil style reflux condenser with a large diameter jacket and coil, similar to CG-1213-L but with detachable hose connections. Connections are made of polypropylene and provide a safe and easy way of connecting and disconnecting flexible tubing to the condenser. Supplied complete with two GL open…

With spiral condensing tube having both inlet and outlet connections at top, on same side. With standard taper joints. Length between joints is approximately 80-90 mm longer than the stated coil length.

Microscale air condenser normally used in reflux experiments. When packed with desiccant material, condenser becomes a drying tube. With inner joint at bottom, outer joint at top. Codes -10, -14 and -17 supplied with drip tip for use with 9595 Spinning Band Column. Effective length, approximately…

High through-put, double coil condensers are designed to fit larger systems and pilot plant reactors. The design is similar to a rotary evaporator type condenser, where large volumes of material are being condensed at high temperatures and where large

Borosil® Double Surface Condensers have a water jacket on the outside and through the center of the condensing tube. This is used when the liquid is very unstable like alcohol, aromatics, essential oils, petroleum products, distilling ethers, etc. These condensers are widely used throughout…

Indentations at the bottom for supporting packing material. Jacket permits the column to be used as a condenser.

Jacket has an O.D. of 40mm while coil O.D. is 8mm to provide maximum cooling capacity.

Allihn Condenser Jacket Length: 120, 200, 300 or 400mm available Joints: 14/20, 19/22 or 29/42 available Hose Connection OD: 8 or 10mm With outer joint at the top and inner joint at the bottom.

Two piece cold trap style condenser for use with rotary evaporators. Condenser has a 50mm flange on the side, a 35/20 lower ball joint, a 19/38 stopcock plug and removable hose connections using GL-14 threads. Condenser is supplied complete with PTFE centering ring along with plastic caps and…

Tightly wound coil provides enough surface area to condense high vapor pressure solvents like hexane. With an internal, coil-type cold finger Standard Taper outer joint at the top, Standard Taper inner drip joint at the bottom 283000 does not have a drip joint Two hose connectors…

Ai SolventVap 2L (evaporating flask capacity) series rotary evaporators come with a modular heating bath, vertical glassware, and digital temperature/rotation control. Its optimized bath volume allows for rapid heat-up times. Thats why our SolventVap evaporators consistently deliver reliable and…

Hopkins condenser with tube fitting Dimensions: 50 x 260mm Joints: 24/40 Compatible With: Central collect S-EVAP KD units

For use in many refluxing operations, including Soxhlet extractions. Straight outlet tube at top Water-cooled Standard Taper inner drip joint at bottom Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

Two piece cold trap style condenser for use with rotary evaporators. Condenser has an additional 19/38 outer joint sealed onto the condenser to allow continuous feed of volumes exceeding the capacity of the evaporating flask.

Liebig condensers are used to cool and condense hot vapor as part of a distilling apparatus. This condenser has a straight inner tube that the condensing vapor passes through, and a larger outer jacket that cooling water passes through. Socket is 24/40

I.D. of inner tube is designed large enough to accept a thermometer. Supplied with one holed compression cap and one Viton® O-ring.

Two piece cold trap style condenser for use with rotary evaporators. Condenser has a 45/40 lower inner drip joint, a 19/38 stopcock plug, and removable hose connections using GL-14 threads. Condenser is supplied complete with PTFE centering ring along with plastic caps and serrated hose…

Borosil® Allihn Condensers have an interchangeable inner and outer joint with a drip tip. The Allihn Condenser has a more surface area than the Liebig, with a series of bulbs which generates a higher cooling capacity. This condenser is ideal for laboratory scale refluxing. There is an inlet and…

Distillation Condenser, Vacuum Jacketed, Joints: 14/20 and 24/40 available, Jacket Height: 130mm and 250mm available, with 12mm ID indentations to support packing material **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**