Lab Glassware

With both ends rounded Designed from Federal Specification NNN-R-560, Type 1 Length x diameter in mm are shown in listings

Comes with Synthware Distilling Adapter (Joints: 14/20, 19/22 AND 24/40) and Cow Receivers (Joints: 14/20, 19/22, AND 24/40). Rotating cow receiver allows four flasks to be progressively filled. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

Glass beads for homogenization, cell lysis

Made of borosilicate glass Contains minimal heavy metals and is practically free from fluorine and alumina Strong, yet soft and pliable Suitable as a filtering medium due to its low alkali content Maximum service temperature 500°C Fiber diameter 0.008 mm

Heavy wall pressure vessels have an internal thread for use with PTFE bushings as pressure seals. The unique design allows hand tightening and loosing for easy access into the vessel. O-ring is positioned on the bushing above the thread for improved sealing. Vessels are useful for pressure reactions...

Adapters are used for reduced pressure filtration with plain stem buchner funnels. Top is tooled to accept the listed size of pluro-stopper. Serrated hose connection has an O.D. of 10mm at the largest serration. FOR PLURO STOPPERS SEE CG-1401.

With 24/40 standard taper inner and outer joints and side hose connection size D.

Used for microscale recrystallizing of small quantities of reaction product. Consists of a glass outer tube with a non-uniform grind to purposely allow leakage, and a PTFE inner plug. The PTFE inner plug fits both the 1.0ml and 2.0ml capacity outer tubes. Capacity listed is the volume of the tube...

Rotating distillation receiver allows four fractions to be collected. Vacuum adapter has a vertical orientation.

With the outer and inner joint at 135° angle, used with short-path.

Adapter has an outer luer joint that provides a convenient way to connect solid phase extraction (SPE) cartridges, tubes or syringes to a standard taper inner joint. The adapter provides for easier sample concentration and clean-up while reducing the chances of cross-contamination. The addition of a...

Across International PTFE sealing sleeve for air tight vacuum operation. Designed with higher and lower bumps to enhance sealing. No-lip top allows you to put on your keck clip securely. This sleeve will increase vacuum level on your glassware setup, allowing you to achieve better results.

Chemistry filter adapter is used for reduced pressure filtration with plain stem buchner funnels. Top has a HEAVY DUTY tooled flare to accept the listed size pluro stopper. Hose connection is 10mm OD at the largest serration. ADAPTER IS NOT SUPPLIED WITH RUBBER PLURO STOPPER. CG-1052-A-14 Accepts up...

For easy separation of water from reaction or distillation system.

Similar in design to AF-0513 but with two oil reservoirs. Bubbler is approx 125mm W x 135mm H. Hose connections are 9mm OD at the middle serration.

All glass and PTFE design cleans five NMR tubes of the same, or various, lengths and diameters. PTFE adapter has five positions with flexible 1/8 " PTFE tubing supplied in 9 " lengths that can be cut to desired height. The NMR tube is placed over the tubing and seats in the adapter,...

This easy-to-apply plastic coating forms a protective film around the outside of a glass component. It will normally contain both the glass particles and the materials inside the vessel should the glass vessel break during an experiment. This is a hard, adherent film and is resistant to leaching and...

Synthware flushing adapter is used to flush and fill attached vessels with an inert gas to provide protective storage. A ballon is connected to the top hose connection. An inert gas is connected to the side hose connection. The ballon can be expanded with inert gas at the same time as the vessel or...

A .002in thick PTFE sleeve for standard taper joints provides a grease-free seal. Sold in packages of 3 each.

Micro midget impinger designed for sampling of small volumes of air at low jet velocity, as per EPA Method 6. Impinger bottle is graduated from 5 to 30ml in 5ml subdivisions. Both the bottle and stopper have 24/40 standard taper joints. The orifice at the impinger tip is 1mm, passing 0.09 to 0.11...

Adapters for use with manifolds such as AF-0450 through AF-0454 to permit port connection to standard rubber hose. Adapters have hooks just below the grind for use with CG-110 stainless steel springs. The 24/40 size is available with a constriction above the serrated hose connection to permit bowl...

Synthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints. 

Vacuum Takeoff Adapter, Microscale, Synthware, Joint: 14/10, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.

These Claisen Heads are replacement parts for the 6949M series of PYREX® microchemistry kits (Thomas No. 0320H44).