Select up to 3 products
Comes with Synthware Distilling Adapter (Joints: 14/20 or 19/22) and Cow Receivers (Joints: 14/20 or 19/22). Designed without hose connection to be used with D10 distillation apparatus. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**
These PYREX® angle connecting adapters have a sidearm at an approximately 120° angle from the lower joint. The lower end is equipped with an inner 24/40 Standard Taper joint, and the upper end and sidearm with an outer 24/40 Standard Taper joint. This tube is also a replacement part for...
Used as a one-time opening valve. Drawn to a point so that a small weight will fracture the seal.
With standard taper 24/40 joint and 8mm O.D. outlet tube bent at 75 degree angle.
Process pipe annealed u bend.
Straight connecting adapter with standard taper inner joints at both ends. Various lengths.
Schwartz drying tube with standard taper stoppers.
Used to regulate the flow of gases or liquids into reaction systems. PTFE stopcock has a bore of 2mm. Hose connection has an O.D. of 8mm at the middle serration.
Schwartz type drying tube having 14/20 hollow stoppers. Stoppers have a hole that aligns with a serrated hose connection for on/off action. Overall height is approximately 170mm.
Used to regulate the flow of gases or liquids into reaction systems. Stopcock has a bore of 2mm and is supplied complete with a CG-423 retaining clip. Hose connection has an O.D. of 8mm at the middle serration.
Craig Recrystallization Tube, Synthware, Complete with glass outer tube and inner plug, Capacity Below Grind: 2mL.
One piece stainless steel KF25/NW25 to 3/8" hose barb adapter for secure vacuum connection. Compatible with the Ai 2.5, 7.2 cfm and Welch 2.3 cfm vacuum pumps, offered by Across International.,/p>
Connecting, reducing adapter with top female joint being smaller than the bottom male joint.
Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With two 4mm drain holes at the base of the inner tube to allow solvent to drain back into the evaporation flask. Has upper outer and lower inner standard taper...
Column length is measured from the highest to lowest indent in the column.
Vacuum jacketed and silvered with viewing strip or unsilvered. For use with No. 7792 Head. With standard taper 24/40 joints. Effective length, 250mm.
Designed for microscale application. With one female joint and four drip-tip male joints.
Septa tops are flanged with a sleeve-like extension that folds down over the vessel's neck. Punctured diaphragm re-seals after syringe is withdrawn. Septa are supplied in a variety of sizes, red, white or grey rubber.
Foxx Life Science EZflow® Glass Filtration is great for filtration of particulate contamination. Our assemblies feature an all glass assembly that is made from high quality ingredients. It includes a flask, funnel cup, membrane holder, and an aluminum clamp. Our glass filtration has high...
For enlarging the size of Standard Taper glass joints. Outer joint is at the top, inner at the bottom Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type 1 and ASTM E438, Type 1, Class A requirements
PTFE adapter, precision made, for use when making NPT thread connectors to Ace-Threds. One end designed to make leaktight seal with Ace-Thred without use of O-Rings, other end accepts NPT male thread. Can be used when making connection at top of rapid prep columns or rigid connection between...
Vacuum Adapter has a ground glass standard taper outer joint on top that provides a convenient leak free way to connect to the OP-6602, OP-6603 and OP-6604 disposable long stem filter funnels and a taper inner joint or a vial. The unique design of the long stem filter funnel and vacuum adapter makes...
PTFE adapter for use with either 1/8"; or 1/4"; thermocouples. Adapter has an outer Viton® o-ring to form a grease-free, airtight seal between the adapter and the listed size of outer joint. The compression nut works in conjunction with the upper Viton® to provide a airtight seal...
Three section Snyder column with improved design to prevent column flooding. Column has a 24/40 top outer joint and a 24/40 lower inner joint for use with CG-1308 Kuderna-Danish flask.