Lab Condensers

The improved design of ACE extractor condensers permits greater condensing capacity, cycling rates may be doubled over conventional style extractors. Complete consists of flask cap, condenser, extractor, and flask.

Of borosilicate glass All sizes have a flange on which they are suspended without use of stopper Total height of 6 3/4” Size A finger is 15 x 75 mm long; flange diameter 50 mm.

This simple PYREX® cold finger condenser, of relatively low efficiency, is often used to regulate refluxing by adjusting the flow of air or water through it (dephlegmation). The tubulation O.D. is approximately 10mm. This condenser has a 24/40 inner Standard Taper joint and is a replacement part...

These 250mL PYREX® atomizers are used for spraying reagents onto thin layer chromatography plates. They have a full length 24/40 Standard Taper joint between the reservoir and spraying device. The PYREX® distilling condenser has 14/20 Standard Taper inner and outer joints, is simple in design and...

This Jacketed Reflux Condenser is a replacement part for the 6949M series of PYREX® microchemistry kits.

Findenser comprises of an internal glass condenser and an external, finned aluminum jacket, between which a small amount of water is permanently sealed. The glass condenser is designed to have a greater internal surface area than traditional condensers, giving it increased heat transfer capacity....

Our 300mm West Condenser is made from high-quality borosilicate glass and has a sealed inner tube, two inlet/outlet arms, and 24/40 ground glass joints. Our Hemple Condenser is made from high-quality borosilicate glass and has a 300mm long condensing column. Our Liebig Condensers are made from...

Extended offset lower tip for drop control.

LIDS, REACTORS, 6-NECK FOR 57MM OD REACTION VESSEL BODY, EQUIVALENT TO METTLER EASYMAX, Reaction Vessel Lid, 6-Nk, for 57mm OD Reactor Body: 14/20 Outer CN, (3) 14/20 Outer SN's, and (2) 10/18 Outer SN's; Equivalent to Mettler  Easymax® Part # 51161619Mettler Easymax® is a...

Small scale Liebig condenser with a standard taper outer joint at the top and a lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

Double jacketed with standard taper inner and outer joint at bottom and top.

Reflux condenser with the coolant circulated through the inner coil instead of through the jacket as in the Graham style condenser. Condenser has standard taper top outer and lower inner drip tip joints. Hose connections have an O.D. of 10mm at the middle serration.

This PYREX® general purpose condenser can be used for either distillation or extraction. Although the condensing area per unit length of the 200mm long jacket is low, the large capacity water jacket gives efficient cooling. Condenser tubulations are approximately 10mm O.D. The adapter end is...

This PYREX® Friedrichs type condenser affords very efficient operation. The helical inner tube fits closely within the jacket. The vapor tube is sealed to the jacket at an angle of 75° and has an outer 24/40 Standard Taper joint.

Friedrichs condenser similar to CG-1210 but with detachable hose connections. Connections are made of polypropylene and provide a safe and easy way of connecting and disconnecting flexible tubing to the condenser. Hose connections have an O.D. of 8mm and an I.D. of 4mm. Supplied complete with two...

With spiral condensing tube having both inlet and outlet connections at top, on same side. With standard taper joints. Length between joints is approximately 80-90 mm longer than the stated coil length.

Coiled Condenser, Removable Hose Connections Joints: 24/40 or 29/42, Jacket Length, 200, 300 and 400mm available Hose Connection: 8mm **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

Vapors rise to the top of inner tube then travel downward and condense in this highly efficient concentrator. Condensate drains through the side tube which has a standard taper inner joint the same size as the lower inner uptake joint. Serrated hose connection for connecting to vacuum source. Hose...

Allihn - suitable for use in vacuum distillations With condensing tube expanded by series of bulbs which increase condensing area and lengthen condensate path Inlet and outlet tubes are on opposite sides of the jacket All sizes take stopper size 3 and have Standard Taper drip tip joint at bottom and...

West Condenser Joints: 14/20, 19/22, and 24/40 available Jacket Length: 110, 190, 200, and 300mm available Narrow annular space for fast collant speed thus high cooling efficiency.

With a joint at 15° angle. Supplied completely with Nylon® cap and hose connections.

Liebig condensers are used to cool and condense hot vapor as part of a distilling apparatus. This condenser has a straight inner tube that the condensing vapor passes through, and a larger outer jacket that cooling water passes through. Socket is 24/40

Graham condenser is designed for use in distillation applications. Constructed of borosilicate glass, this condenser has a coiled inner tube to provide additional surface area for highly efficient cooling. Socket is 24/40 with a screw thread connector.

The Graham Condenser has a coiled inner tube to allow a greater surface for coiling and condensation. Made from heat resistant borosilicate glass. The inner coil is sealed to the outer coil producing a leak proof unit.