Ace Glass

Ace Glass

Products (377)

Compare Tool

Select up to 3 products

  • Agitator, PTFE, Large Scale Multi-blade

    These heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.

  • Midget Bubbler

    Identical to 7531-10 with the exception that the nozzle is replaced by a sintered glass filter, porosity A (145-175 microns). Used in determination of Acrolein: 4-Hexylresorcinol Method #1. Bottle has encircling graduations from 0 to 25mL or 0 to 30mL in 5mL divisions. Inlet/ outlet are 7mm O.D. For...

  • Adapter, Reducing

    Connecting, reducing adapter with top female joint being smaller than the bottom male joint. The Ace Glass Adapter, Reducing, offers a reliable solution for connecting glassware with differing joint sizes. This adapter is crafted from high-quality glass to ensure a secure fit and seal during...

  • Condenser, Spiral

    With spiral condensing tube having both inlet and outlet connections at top, on same side. With standard taper joints. Length between joints is approximately 80-90 mm longer than the stated coil length.

  • Column, Chromatography

    Rugged columns with internally threaded ends to which a wide choice of upper and lower end pieces can be fitted using 5837, 5838, 5841, 5842, and 5843 fittings. Available in a variety of lengths and diameters. Some sizes available with epoxy coating for added protection against scratches.

  • Flask, Two Neck, Angled Side Neck

    Two neck, one center and one angled side neck, round bottom flask with standard taper joints. Available in standard wall or heavy wall.

  • Glass Cloning Cylinder

    Glass cloning cylinder for cloning or isolating individual cells. Place cylinder into bottom of flask or Petri dish to isolate individual or small group of cells. Disinfectant chambers to be used as described in the 1992 J.A.O.A.C. Hard Surface Carrier Test.

  • Stirring Shaft, Polished 316 Stainless Steel, 10mm

    Polished stainless steel stirring shafts, 10mm OD, drilled type with removable button. When used with 8066 PTFE bearing, a lubricant-free vacuum seal can be realized at speeds up to 200 rpm. Recommended for use with 8044,8050,8066,13443 and 13445 bearings. With button, shaft accepts...

  • Column, Distillation, Hempel

    Vacuum jacketed and silvered with viewing strip or unsilvered. For use with No. 7792 Head. With standard taper 24/40 joints. Effective length, 250mm.

  • Septa, Rubber

    Ace Glass

    Septa tops are flanged with a sleeve-like extension that folds down over the vessel's neck. Punctured diaphragm re-seals after syringe is withdrawn. Septa are supplied in a variety of sizes, red, white or grey rubber.

  • O-Ring

    Ace Glass

    O-Rings in a variety of sizes and materials. Please see o-ring materials chemical compatibility here: http://www.aceglass.com/downloads/eccc.pdf

  • Rings, Raschig

    Fabricated from Borosilicate glass. Wall weight on 5mm size is approximately 0.8, other sizes have wall weight of approximately 1.0/mm.

  • Head, Pressure Reaction, with Ace-Threds

    Rugged, heavy wall head for use with 6384, 6386, 6388, 6423, 6425, 6427, or 6429 reaction flasks. Duran flange supplied with a shallow O-Ring groove for use with mating grooved flask. #15 Ace-Thred center and various #15 and #7 side necks available allow connections under pressure conditions without...

  • Adapter, End Fitting, NPT to Ace-Thred, Michel-Miller

    PTFE adapter, precision made, for use when making NPT thread connectors to Ace-Threds. One end designed to make leaktight seal with Ace-Thred without use of O-Rings, other end accepts NPT male thread. Can be used when making connection at top of rapid prep columns or rigid connection between...

  • Flask, Recovery, Rotary Evaporator, Indents

    Replacement drying flask for Buchi rotary evaporators. Pear shaped heavy wall with a standard taper single neck. Available plain or safety coated.

  • Beaded Pipe to Standard Taper Joint Adapter

    Borosilicate glass transition adapter to convert beaded pipe 2 to standard taper joint. The Beaded Pipe to Standard Taper Joint Adapter by Ace Glass is engineered for seamless integration of beaded pipes with standard taper joints. Its precision design ensures a snug fit, reducing the potential for...

  • Beaker, Jacketed

    Jacketed beaker with one upper and one lower hose connection on opposite sides. Also available with Ace-Safe connections. All are without a pouring spout.

  • Adapter, Sublimation

    Unique device for carrying out sublimation directly in round bottom reaction flask; simply remove condenser, stirrer, etc. from joint, insert sublimation adapter and begin. Coolant connection at top and side vacuum connection are 9.5 mm (3/8") O.D. Vacuum connection is controlled by 1:5 PTFE 2 mm...

  • TUBE, Receiving, Graduated

    100ml graduated, rotary evaporator receiving tube. Tapered bottom with 35/20 spherical outer joint top. Graduated in 0.5ml increments to 10ml, 5ml increments to 100ml.

  • Extraction Apparatus, Soxhlet Improved Design

    The improved design of ACE extractor condensers permits greater condensing capacity, cycling rates may be doubled over conventional style extractors. Complete consists of flask cap, condenser, extractor, and flask.

  • Funnel Addition, Pressure Equalizing, Jacketed

    Jacketed version of 7297 series addition funnels. Jacket runs from shoulder at top of vessel to above the PTFE stopcock. Has size D hose barbs for 3/8in ID tubing. Pressure equalizing arm runs from top of vessel to just below the PTFE stopcock. Graduat

  • Bushing, Ace-Thred Connector

    Bushing connector for joining an Ace-Thred to a reduced end tube. Assorted bushing and o-ring materials.

  • Fernbach Flask, Baffled, Beaded Neck

    Fernbach style culture flask with wide-mouth and beaded neck. The flask is triple baffled on the bottom edges to achieve maximum oxygen transfer to the culture medium. 63mm ID beaded neck accepts cotton plugs or rubber stoppers.

  • Adapter, Claisen

    Adapter with parallel side arm, outer joints at top, inner joint at bottom. This Claisen Adapter is designed to facilitate complex distillation processes in laboratory settings. Its three-joint design allows for the connection of multiple components, simplifying the setup and execution of various...

Compare Tool

Select up to 3 products