Ace Glass

A front-seal, solid plug for sealing column ends. Supplied with one FETFE o-ring.

PTFE stir blades for button type stir shafts. 10mm OD shafts can be found in our product series 8068, 8070, 8074 and 8075. 19mm OD shafts can be found in our 8076 and 8077 series.

The Dounce type, glass tissue grinder is supplied with two glass pestles; one with a tight inner tolernace and one with a loose inner tolernace. The loose pestle can be used for initial reduction of the tissue sample and the tight pestle can be used to fine grind the tissue and complete the...

With 24/40 standard taper inner and outer joints and side hose connection size D.

Round bottom, heavy wall, pressure rated flask. All flasks come complete with a solid PTFE plug seal with front seal FETFE o-ring for better containment of product. Vessels are tested at 1.5x for a working pressure rating at 60PSI at 120°C. Flasks

Large scale sublimation apparatus constructed of heavy wall glass. Will sublime 100gms of solid sample. Cold finger tube positions in center neck and is held by a plastic bushing to a threaded condenser flask. All joints are PTFE-Clad to eliminate the use of grease and still avoid freezing. Kettle...

Round bottom flask with a single neck. Available in heavy wall.

With fritted disc sealed on bottom. Overall length 125mm. All porosities of a given size are priced the same.,/p>

Collection bottle, usually connected to the bottom arm of the 7495 tee with reduced ends, to collect heavy particulates before they enter the manifold train.

303 stainless steel support rods, 13mm (1/2") O.D. for use in place of aluminum or fiberglass. For use with all standard laboratory connectors.

Impingers used for sampling small air volumes at low velocities. Bottle with 24/40 stopper joint is available in 25 or 30ml sizes. The stopper is available with an open nozzle or one calibrated to deliver 0.09 to 0.11 CFM at 30.5cm (12in) vacuum. The stopper inlet is available as an open tube end,...

With outer joint. 125mL 28/15 used as collection flask at bottom of 7515 sampling cyclone. Available in 300mL and 500mL with 35/25 outer joint.

Heidolph RZR 1 overhead stirrer with tools and accessories features 2 gears delivering 280 to 2200rpm with analog control. 115v 60Hz input motor is high torque, up to 100Ncm. Use code -32 stir shaft for slow speed, up to 250rpm and code -34 shaft for speeds up to 2200rpm. Universal stand and clamp...

Economy Model, compact, digital temperature controller. 16 segment ramp and soak, fuzzy logic, auto tune PID controller. One T, K, or J type sensor input. One 120V output. Temperature range varies by thermocouple type. Control accuracy -plus - minus 0.1 Degree C. Absolute accuracy of plus-minus 0.25...

Round bottom flask with two socket joints.

Flat gaskets for sealing two flat ground glass surfaces. Plain flat or grooved PTFE gaskets reduce breakage and make an effective seal. Our flat, exclusive FETFE gasket provides a leak-free seal with slight clamp pressure. These are designed especially for use with our conical or flat ground flange...

Straight bore stopcock plugs, available in borosilicate or PTFE. PTFE plug Corning# 7681.

Guy-Lussac type calibrated and engraved. Comes complete with stopper and bottle.

Flat bottom, three neck flask can sit on stirrer hot plate with no further support. 250ml and 500ml sizes feature angled side necks while the 1000ml size necks are vertical.

Used in ASTM D1319-65T, a "test for hydrocarbon types in liquid petroleum products." Consists of a charger section with a capillary neck, a separator section, and an analyzer section. Upper joint spherical 28/12.

Shake style culture flask with beaded neck and three bottom edge baffles to enhance mixing and oxygen transfer to media.

All-PTFE turbine type agitator. Unique locking arrangement assures positive grip. Agitator fits 10 mm shafts. Shaft opening is drilled straight thru to allow positioning of agitator at any drilled position on shaft as well as the bottom. For use with bead type glass shafts, 8068-G, 8075 or PTFE...

Stopcock adapter, top outer joint, bottom inner joint, PTFE plug. Spherical joint versions are both outer joints top and bottom.

Outside diameter of tube 8mm, total length of tube 150mm. All porosities of a given size are priced the same.