Jacketed Condenser

Compare Tool

Select up to 3 products

Jacketed Condenser
1 - 32 of 129
Sort
View
Show
  • SYNTHWARE Grahm Condensers

    Kemtech America

    Graham Condenser Joints: 14/20, 19/22 and 24/40 available Jacket Length: 120, 200, 250, 300 and 400mm available Hose Connections: 8 or 10mm available **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

  • I.D. of inner tube is designed large enough to accept a thermometer. Supplied with one holed compression cap and one Viton® O-ring.

  • Reflux Condensers

    Chemglass

    Reflux condenser having an internal coil that is water jacketed. Vapors are condensed both on the coil and the inner wall of the jacket. The top end has a standard taper outer joint and the lower end has an inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

  • Vacuum jacketed Vigreux distillation head having a sealed on condenser, braced for strength. The top outer joint is for a 1” immersion 10/18 or 10/30 thermometer. Vacuum adapter has an inner joint and a sealed in drip tip. Condenser length is 100mm on the 14/20 size and 200mm on the 24/40 and…

  • Indentations at the bottom for supporting packing material. Jacket permits the column to be used as a condenser.

  • Graham Coiled condensing tube is sealed into water jacket Inlet and outlet tubes on opposite sides of jacket With Standard Taper drip tip joint at bottom and Standard Taper outer joint at top The 8” condenser has 19/38 joints; others have Standard Taper 24/40 joints

  • Distillation Condenser, Vacuum Jacketed, Joints: 14/20 and 24/40 available, Jacket Height: 130mm and 250mm available, with 12mm ID indentations to support packing material **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

  • This Jacketed Reflux Condenser is a replacement part for the 6949M series of PYREX® microchemistry kits.

  • Jacketed distilling column has indentations on the inner tube to support packing material. The jacket allows the column to be used as a condenser. Column has a top outer and lower inner standard taper joint. All sizes have an I.D. of approximately 10mm.

  • …insulation jacket (a $399 value) with open/close viewing window and top/bottom adjustable drawstrings, specially designed and made for Ai glass jacketed reactors. These jackets will extend chiller life, allow you to go down to a lower temperature, and also cut your utility bill. Dual jacketed

  • condensers, giving it increased heat transfer capacity. The finned jacket fits around the glass condenser further increasing the external surface area. The result is a super air condenser that performs as well as a traditional water condenser. Replaces the need for water cooled condensers in over…

  • This specially designed PTFE condenser jacket is a replacement part for the PTFE Cyanide Distilling Apparatus (Thomas No. 0320A91)

  • SYNTHWARE Allihn Condensers

    Kemtech America

    Allihn Condenser Jacket Length: 120, 200, 300 or 400mm available Joints: 14/20, 19/22 or 29/42 available Hose Connection OD: 8 or 10mm With outer joint at the top and inner joint at the bottom.

  • Indentations at the bottom for supporting packing material. Jacket permits the column to be used as a condenser.

  • … Vertical intensive condenser with double jacket and distributor for particularly efficient condensation. The solvent to be distilled can be continuously fed in at the distributor using the PTFE inlet tube. Thomas No. 1203C94 Vertical intensive condenser with double jacket and distributor for…

  • Condenser, Liebig

    Ace Glass

    With straight inner tube sealed through the jacket. This condenser is acceptable for use with Abderhalden or Mini-Lab moisture test apparatus.

  • Vacuum jacketed design for more efficiency. When a thermometer is inserted in the top of this apparatus, the bulb and stem serve as column packing. The close coupled condenser and vacuum connection offer and extremely short condensate travel path. Used with 25mm immersion thermometer, and D27…

  • Can be used as a distilling head to connect a condenser to the top of the distillation column. The 10/18 top joint accomadates a 76mm immersion thermometer.

  • condenser used in reflux experiments. With outer joint at top externally threaded to allow an O-RING-CAP-SEAL connection with mating male joints and inner joint at bottom, with drip tip. I.D. of inner tube on code -23 is sufficiently large enough to accept regular size thermometer. Jacket length…

  • Adapter is vacuum jacketed and can be used as a distilling head to connect a condenser with the top of the distillation column. The 10/30 top outer joint is for use with CG-3506, 75mm immersion thermometers. Inner joints are at a 75º angle to one another and are both the same size. For…

  • Glass, jacketed reaction vessel design for use with our 7874 quartz and 7875 glass immersion wells. Instead of a standard taper joint, this reactor utilizes a height-adjustable, non-freezing #50 Ace-Thred. Also featured, a 14/20 angled joint for a sparger tube, a 24/40 vertical joint for a condenser

  • Jacketed receiver with vacuum manifold for removal of sample during operation without disturbing the system. Stopcocks on manifold are 4mm bore, receiver stopcock is 3mm. Hose connections are size E on condenser; 10mm O.D. olive on manifold.

  • Used as distilling head for connecting top of column with condenser. Top 10/30 standard taper joint for 76mm immersion thermometer.

  • These PYREX® condensers have a high surface area per unit length of the 200mm long jacket with a 19/38 Standard Taper outer joint at the top and a plain drip tip at the bottom. They are primarily used in distillation assemblies Condenser tubulations are approximately 10mm O.D.

  • jacketed reactor system optimized for decarboxylation reactions. Glass reactor temp range -60C to 200C, air stir motor in mobile steel frame. NRTL, facility power requirements: Circuit #1 = 120V / 1ph / 20A, Circuit #2 = 230V / 1ph / 20A Cooling System: Cooling to the glass condenser

  • …for condenser and one #7 Ace-Thred side arm for thermometer. Center joint is 60/40. Bottom of reactor is flat to allow use of stirrer magnet. Volumes indicated are total volumes. Volume in reactive area of lamp is approx. 40-50% of total volume. Available with vessel plain or jacketed. Complete…

  • Vacuum jacketed Vigreux distillation head having a sealed on condenser, braced for strength. Vacuum adapter has an inner joint and a sealed in drip tip. To be used with a 25mm immersion thermometer .

  • Similar to D451414-series but with the uptake tube vacuum jacketed to improve distillation performance. The jacket eliminates the possibility of condensation or recrystallization of distillate in the sidearm. With 2mm PTFE stopcock.

  • Designed for small chemical applications. Improved design permits greater condensing capacity. Condenser approximately 139mm jacket length. Joint between condenser and extractor is 24/25. Flask joint is 14/20. Designed to accommodate paper thimble, size 10 x 50 mm. Flask is 30mL capacity. Hose…

  • This PYREX® general purpose condenser can be used for either distillation or extraction. Although the condensing area per unit length of the 200mm long jacket is low, the large capacity water jacket gives efficient cooling. Condenser tubulations are approximately 10mm O.D. The adapter end is…

  • …lifespan operations. Now includes a FREE high quality thermo insulation jacket with open/close viewing window and top/bottom adjustable drawstrings, specially designed and made for Ai glass jacketed reactors. These jackets will extend chiller life, allow you to go down to a lower temperature, and…

  • Model SCO5W water jacketed CO2 incubator and is an ideal unit for cell culture applications. It provides a precisely controlled, accurate, pure environment throughout the culturing process. Shel Lab CO2 incubators are designed to provide the uniform temperatures and highly…

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.