Condensers, Chemicals
-
Condenser, Spiral
Ace GlassWith spiral condensing tube having both inlet and outlet connections at top, on same side. With joints. Length between joints is approximately 80-90 mm longer than the stated coil length. Available with PTFE clad bottom joint.
-
Reflux Cold Finger Type Condenser
labForce® (powered by Thomas Scientific)Of borosilicate glass All sizes have a flange on which they are suspended without use of stopper Total height of 6 3/4” Size A finger is 15 x 75 mm long; flange diameter 50 mm.
-
Condenser, Finger, with Joint
Ace GlassCold finger condenser for use with our 7756 series Schlenk reaction vessels.
-
SYNTHWARE Liebig Condensers
Kemtech AmericaLiebig Condenser Jacket Length: 100, 120, 180, 200, 250, 300, 400, and 500mm Joints: 14/20, 19/22 and 24/40 available Hose Connection: 8 or 10mm With outer joint at the top and inner joint at the bottom.
-
Coil style reflux condenser with a larger diameter jacket and coil, thereby providing maximum cooling capacity, while being shorter in length. Hose connections are on the bottom of the condenser which makes it easier to connect hose/tubing. Connections are GL14 polypropylene hose barbs and screw…
-
Condenser, Reflux
ChemglassCoil style reflux condenser with a larger diameter jacket and coil, thereby providing maximum cooling capacity, while being shorter in length. Hose connections are on the bottom of the condenser which makes it easier to connect hose/tubing. Jacket has a O.D. of 41mm while the coil O.D. is 8mm.…
-
SYNTHWARE Coil Reflux Condenser
Kemtech AmericaCoil Reflux Condensor, Microscale, Synthware, Joint: 14/10, for low boiling solvents, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.
-
PYREX Liebig Condensers
CorningWith Standard Taper 24/40 joints Inlet and outlet tubes, 10 mm o.d. are on opposite sides, indentations at lower end of condenser tube support packing when used as fractionating column.
-
Micro Soxhlet, Improved Design
Ace GlassDesigned for small chemical applications. Improved design permits greater condensing capacity. Condenser approximately 139mm jacket length. Joint between condenser and extractor is 24/25. Flask joint is 14/20. Designed to accommodate paper thimble, size 10 x 50 mm. Flask is 30mL capacity. Hose…
-
Condenser Liebig Standard Joints
GSC International, Inc.Our Liebig Condensers are made from high-quality borosilicate glass and have a straight sealed inner tube and two inlet/outlet arms. These condensers have standard joints. We also sell Liebig condensers with rubber connections or ground glass joints . PRODUCT WARNINGS Our products…
-
Graham Condensers
ChemglassCondenser has a top standard taper outer and lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.
-
SYNTHWARE Allihn Condensers
Kemtech AmericaAllihn Condenser Jacket Length: 120, 200, 300 or 400mm available Joints: 14/20, 19/22 or 29/42 available Hose Connection OD: 8 or 10mm With outer joint at the top and inner joint at the bottom.
-
High Efficiency Reflux Condensers
ChemglassCompact high efficiency reflux condenser employs a double wall thimble shape bulb sealed into the outer jacket. Serrated hose connections for water connection extend through the outer bulb and have an O.D. of 10mm at the middle serration. While the overall height of this condenser is only…
-
SYNTHWARE Air Reflux Condenser with 14/20 Joint
Kemtech AmericaAir Reflux Condensor, Synthware, Joints: 14/20, Overall Length: 143mm, Length Between Joints: 96mm.
-
Reaction Vessel
ChemglassLIDS, REACTORS, 6-NECK FOR 57MM OD REACTION VESSEL BODY, EQUIVALENT TO METTLER EASYMAX, Reaction Vessel Lid, 6-Nk, for 57mm OD Reactor Body: 14/20 Outer CN, (3) 14/20 Outer SN's, and (2) 10/18 Outer SN's; Equivalent to Mettler Easymax® Part # 51161619Mettler Easymax® is a…
-
Double-jacketed, with standard taper 24/40 inner and outer joint at bottom and top. Extra cooling capacity for volatile materials. Compact design retards diffusion. With #7 Ace-Thred and Ace-Safe PTFE hose connections on inlet and outlet with barb for
-
Two piece cold trap style condenser for use with rotary evaporators. Condenser has an additional 19/38 outer joint sealed onto the condenser to allow continuous feed of volumes exceeding the capacity of the evaporating flask.
-
Two piece cold trap style condenser for use with rotary evaporators. Condenser has an additional 19/38 outer joint sealed onto the condenser to allow continuous feed of volumes exceeding the capacity of the evaporating flask. The 19/38 joint is sealed at an angle which allows the condensate to fall…
-
Condenser, Long Path
Ace GlassTurbulent flow created makes this condenser very desirable for use under reduced pressure. Internal and external cooling surfaces result in high efficiency per unit length. Joints are standard taper 24/40.
-
SYNTHWARE Grahm Condensers
Kemtech AmericaGraham Condenser Joints: 14/20, 19/22 and 24/40 available Jacket Length: 120, 200, 250, 300 and 400mm available Hose Connections: 8 or 10mm available **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**
-
Condenser 200 mm
CorningThese PYREX® condensers have a high surface area per unit length of the 200mm long jacket with a 19/38 Standard Taper outer joint at the top and a plain drip tip at the bottom. They are primarily used in distillation assemblies Condenser tubulations are approximately 10mm O.D.
-
Ai 2L SolventVap W/ Electric Lift And Cold Trap Condenser 110V
Across InternationalAi SolventVap 2L (evaporating flask capacity) series rotary evaporators come with a modular heating bath, vertical glassware, and digital temperature/rotation control. Its optimized bath volume allows for rapid heat-up times. Thats why our SolventVap evaporators consistently deliver reliable and…
-
Condenser, Dewar
Ace GlassFor use with dry ice and other solid cooling agents. Can also be adapted for use as a small constant temperature bath by using a constant boiling liquid. In this manner, can also be used as an oil bath. The larger size will hold 100mL flask, small size
-
Allihn style reflux condenser similar to CG-1206 but with detachable hose connections. Connections are made of polypropylene and provide a safe and easy way of connecting and disconnecting flexible tubing to the condenser. Hose connections have an O.D. of 8mm and an I.D. of 4mm. Supplied complete…
-
West Condensers
ChemglassNarrow annular space between jacket and inner tube of the West condenser provides for excellent cooling efficiency due to the increased flow rate of water. Condenser has a top standard taper outer joint and a lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.
-
Borosil® Double Surface Condensers have a water jacket on the outside and through the center of the condensing tube. This is used when the liquid is very unstable like alcohol, aromatics, essential oils, petroleum products, distilling ethers, etc. These condensers are widely used throughout…
-
Condenser, Cold Finger
Ace GlassJacket length is measured from the lower shoulder of the bulb to the bottom of the finger. Diameter of tube is 14mm. Used in 6472 Pilot Plant Reactor.
-
SYNTHWARE Friedrichs Condenser
Kemtech AmericaFriedrichs Condenser, Joint: 24/40, Overall Height: 330mm, Hose Connection: 10mm
-
SYNTHWARE West Condensers with Removable Hose Connections
Kemtech AmericaWest Condenser, Removable Hose Connections Joints: 14/20 and 24/40 available Jacket Length: 110, 190, 200, and 300mm available Condensers feature narrow annular space for high coolant efficiency.
-
SYNTHWARE Jacketed Distillation Condensers
Kemtech AmericaIndentations at the bottom for supporting packing material. Jacket permits the column to be used as a condenser.
-
SYNTHWARE West Condensers
Kemtech AmericaWest Condenser Joints: 14/20, 19/22, and 24/40 available Jacket Length: 110, 190, 200, and 300mm available Narrow annular space for fast collant speed thus high cooling efficiency.
-
Cold Finger Condensers
ChemglassCondenser has an inner joint and a sealed lower drip tip for drop control. Hose connections have an O.D. of 10mm at the middle serration.