Distillation Glassware

This distillation set is made from heat-resistant borosilicate glass and held together with rubber stoppers. Includes: 1 Liebig Condenser, 300mm long with a fused inner tube (#30721) 1 Flat Bottom Boiling Flask, 500ml (#FFB500) 1 Erlenmeyer Flask, 500ml (#EF500) 1 Burette Clamp…

…Tube. The Thermometer, with a range of -10° to 50° C and filled with a petroleum-based solution with red dye, connects to the Distillation Head through the 10/30 port. Penny Head Glass Stoppers are included to cap the 50ml Single Neck round bottom flasks after distillate is collected.

Synthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints. 

…300mm long with 24/40 ground glass joints 1 Distilling Arm with 24/40 ground glass joints (#4009) 1 Support Stand 1 Support Ring and Clamp (#4-SRC47) 1 Burette Clamp (#4-BC37) 1 Glass Stopper (#4007-GS)   These Distillation Arms are made from borosilicate glass. Each…

Conforms to ASTM D 4006 Apparatus is used for the distillation of water in crude oil. Apparatus includes 1,000 mL RB flask, 24/40 joints, Dean-Stark distillation receiver, dry trap and Liebig condenser Heating mantle must be purchased seperately

These borosilicate glass distilling receivers with inner and outer Standard Taper joints are used to determine the amount of dilution in crankcase oils when gasoline has been used as fuel. Receiver design keeps heat-sensitive materials away from the hot base of the flask. Calibrated "to…

Suitable for microchemical applications Side-arm on all sizes is approximately 77 mm below the top of the neck at an angle of 75° Adaptable for use with thermometer calibrated for 76 mm immersion 50 mL flask takes rubber stopper No. 1; 250 mL flasks, stopper No. 3; 500 mL flask, stopper No. 4;…

Used for the determination of sulfites in food and related product, this Monier-Williams Sulfites distilling apparatus is made of borosilicate glass and has Standard Taper 24/40 outer and inner joints. The complete unit consists of a special outlet adapter with a double bend, a 300mm long Allihn…

… Short Path Distillation Head, Vacuum Jacketed, 24/40, 34/45 . . . . . . . . 2 Flask, Round Bottom, 3-Neck 10000ml 24/40, 34/45 . . . . . . . . . . . . . . . 1 Distillation Receiver, Cow-Type, 250ml, 1-to-3, 24/40 . . . . . . . . . . . . . . 2 Clamp for Jointed Glassware, Plastic, size 24…

Synthware distillation adapter with a 10/18 standard taper outer joint for a 76mm immersion thermometer. The adapter has a standard taper top outer joint and inner joints for the bottom and side.

…distilling kit, made from heat-resistant borosilicate glass, is intended to produce botanical essential oils. Includes: 1 Erlenmeyer Flask, 500ml (#EF500) 1 Distillation Flask with Thermometer Holder, 1L with a 24/40 ground glass joint (#FLSK-24-40-1L) 1 Biomass Flask 1 Distilling…

Similar to CG-1032, but with joints of non-similar sizes at the upper and lower portion of the adapter. Dimensions are the same as the CG-1032.

Standard Taper 10/30 thermometer opening, distilling, three-way, Standard Taper joints Sidearm is at an angle approximately 75° from the lower part of the vertical tube The joint on the sidearm is at an angle approximately 105° from the sidearm The sidearm and lower tube are…

60° angle Three Standard Taper 24/40 joints Approximate length 206 mm This tube is also a replacement for organic chemistry kits. Type I, Class A borosilicate conforming to federal specification DD-G-54 lb and ASTM E 438. Also meets the US Pharmacopoeia specs for Type I borosilicate glass.

…distilled water for higher purity levels. The first stage distillation is carried out in a glassware set mounted at the front of the cabinet allowing easy access for descaling. The distilled water is fed to a second set of glassware mounted at the rear and distilled a second time. The rear glassware…

Synthware distillation connecting adapter. With standard taper top outer joint and inner joints at bottom and the side arm. Bottom and side arm joints are angled at 75 degrees to one another.

These Distillation Arms are made from borosilicate glass. Each have a 24/40 ground glass joint on top, but their bottom joints vary in the size. They are made to fit our biomass flasks . PRODUCT WARNINGS WARNING: This product can expose you to chemicals including lead, which are known…

Adapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top standard taper outer and lower inner joints, both being the same size.

Synthware distillation adapter bent at 75 degrees. Both ends are standard taper inner joints and are the same size.

Provides dual entry into a variety of flasks BEVEL-SEAL adapters allow temperature measurements at either top outer opening. Useful for reflux with addition- type reactions. Adapter consists of two female standard taper joint fittings at the top and one male standard taper joint at the bottom.…

Plastic conical joint clips are size 24, designed to securely hold 24/40 joint size glassware together.  Note: Clips shipped are blue

…for distillation heads will keep your distillation setup at the peak of its performance. A right-facing observation window allows you to see exactly what is happening inside your glassware. A left-facing observation window allows you to see exactly what is happening inside your glassware. …

…the separatory funnel for extractions and for liquid addition in reaction assemblies. Classical atmospheric, steam, fractional, and vacuum distillations are possible with kit components. Apparatus set-up time is minimal, providing the student with more lab time. Smaller quantities afford a greater…

…extremely efficient use of the 1500 cm² cooling surface. Digital displays for speed and heating bath temperature enable optimum control of all distillation processes. New: 4 l heating bath integrated safety lift-out function in case of power failure package includes Woulff bottle …

Modified Dean-Stark trap allows for more efficient cooling and separation of the azeotrope during distillation. Graduated from 0 to 10ml in 0.2mL subdivisions. **Design suggested by Dr. Craig Merlic, University of California, Los Angeles, California

Ammonia/Phenols and Cyanide Models Available Corrosion resistant PTFE-coated glass 30" x 14.25" footprint Overtemp protection switch Automatic shutoff MIDI-VAP 4000 Systems feature a pre-programmed digital controller with automated shut-off when reaction time is completed. They use…

The Ai heavy wall short path distillation head with vacuum jacket. Features Heavy wall for durability Boiling flask and distribution ports Vacuum jacketed Five sets of vigreux Thermo probe port: 14/20 joints Recirculating fluid ports: GL-16 adapters Glass material:…

…these Bidwell-Sterling moisture traps are calibrated "to contain" (TC) at 20°C and are used for determining moisture in samples by distilling with an immiscible liquid. Consist of vapor tube, return tube, round bottom graduated tube, and Standard Taper 24/40 inner and outer joints. …

Short Path Distillation Head with 24/40 flask joints and 10/30 thermometer port. Distillation head is manufactured from high quality 3.3 borosilicate glass and features a condenser coil and three 1/4" hose nozzles, two for condenser and one for vacuum.

Distillation receiver carts for use with our 10L thru 100L reactor systems. Heavy Duty support cart can be used for round bottom flasks or cylindrical distillation receivers. Rear of cart incorporates 1/2” stainless steel lattice for mounting support clamps or accessories. Glassware can be…

Bent angle of 105°, with Standard Taper joints on inlet and outlet ends and inner drip-tip which bypasses vacuum take-off tubulation Has drip-tip at exit end Side-arm accepts 5/16” i.d. flexible tubing Made from Kimax® Brand KG-33 borosilicate glass, which features a low coefficient of…

Adapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top outer and lower inner standard taper joints.