Flat round edge nickel-plated steel wire jaw construction.

With a full 360° jaw rotation, this fully adjustable clamp is ideal for attaching to rods up to 3/4" (19mm) in diameter. The clamp has an aluminum muff with steel thumbscrew and phosphor bronze jaws. The maximum distance from the jaw to the muff is 4-3/8" (111mm) and the overall length is 5-1/2" (140mm).

This clamp can be instantly detached from vertical surfaces such as heaters. It is constructed of aluminum and incorporates a 5/16"-18 by 1-1/4" steel thumbscrew. The clamp is 1-3/16" wide by 2-15/16" (30mm x 59mm) long and measures 1-3/8" (35mm) from muff center to the dovetail.

Screw Compressor Clamp, Standard Open-Jaw C-Clamp without side post. Jaw Opening: 0-7/8" (0-23mm) Max Height, 1-1/8" (30mm) Max Width

Used to accurately and quickly count pendulum swings, bacteria colonies, drops from pipettes, alpha particles, etc. Tallies up to 9999 by one, quickly resets to zero. Mounted in round 2" (51mm) diameter chrome plated case with finger ring.

Manufactured from heavy die-cast aluminum, this clamp is designed for clamping two pieces of apparatus into any of the three following positions: right angles, parallel, or vertically. The clamp will accommodate attachments up to 1/2"(13mm) in diameter.

These Rod Clamps are otherwise known as the "muff" portion only and can be used to create custom clamps to satisfy a wide range clamping applications.

Distance from center of ring to center of clamp: 4-1/4" (108mm). Plated. Attaches to support rods up to 3/4" (19mm) in diameter.

Designed to safely and conveniently secure compressed gas cylinders in an upright position. Accommodates cylinders 4-1/2" to 11" (114mm to 279mm) in diameter. The heavy-duty clamp with adjustable thumbscrews fits conveniently on any bench up to 2" (51mm) thick without marring the surface.

Similar to the H-8950, this clamp has a phosphor-bronze spring clip attached to an aluminum rod-holding block for thermometers and 2 "v" notches designed to hold the H-1602 ring and stem assembly in an ASTM Softening Point Apparatus, but can be used to suspend other items, such as pitch cubes. The…

The Clamp Hook locks into any position to support suspended thermometers, drying tubes and potash bulbs. The unit has an easy-adjusting check nut and has a 5-1/8" (130mm) maximum distance from center of muff to the hook. The minimum distance is set at 4-1/2" (114mm).

The Humboldt Mfg. Co single ring tripod is suitable for use in research facilities and chemical laboratories while conducting experiments. It is made of high quality material which ensures long lasting usage.

Powder-coated with plated steel rod

Designed to allow users to mount rod vertically or horizontally. The clamp is cast iron with a black enamel finish. Supplied complete with a 3/8" x 20" (10mm x 508mm) rod (H-21350) or a 1/2" x 24" (13mm x 610mm) rod (H-21360).

Highly versatile, the rod height can be locked into any position by a simple thumbscrew located on the outer edge of the clamp. The clamp features a sturdy handle for tightening the unit on the edge of a table top up to 1-1/2" (38mm) thick. The plated, solid steel rod is 1/2" (13mm) in diameter by…

For attaching extension clamps to supports Aluminum construction Has swivel for rods up to 5/8” diameter

These Rod Clamps are otherwise known as the "muff" portion only and can be used to create custom clamps to satisfy a wide range clamping applications.

Screw Compressor Clamp, Closed-Jaw C-Clamp with Side post for tubing insertion. Jaw Opening: 0-7/8" (0-23mm) Max Height, 1-1/8" (30mm) Max Width

This highly stable jack can be adjusted to any height between 2-1/2" to 10" (64mm to 254mm). The jack will accept loads up to 10 lbs. (45.4 kg). The unit is constructed of aluminum top and bottom plates with a baked-enamel finish and plated steel cross members. Height adjustments are achieved by…

Similar in design to our Screw Compressor Clamps except that the compression adjustment screw has a 1" (25mm) diameter serrated head for greater leverage. The clamps are constructed from brass and plated for corrosion resistance.

Two prong zinc-plated, stamped steel with aluminum alloy holder is adjustable by checknut to any angle Takes objects from 3/8” to 1 3/8” diameter. Fits rods up to 1/2” diameter. Length: 6 3/8”.

Hook Collars are used for attaching pulleys, balances, cords, trusses, pendulums, and other apparatus to support rods. The collars are plated for corrosion resistance and are supplied complete with thumbscrew and hook.

Similar in design to our Screw Compressor Clamps except that the compression adjustment screw has a 1" (25mm) diameter serrated head for greater leverage. The clamps are constructed from brass and plated for corrosion resistance.

The Humboldt Mfg. Co test tube clamp is suitable for use in research facilities and chemical laboratories while conducting experiments. It is made of high quality material which ensures durability and long lasting usage.

The "Hoffman Type" Electrolytic Support is used with associated glassware to demonstrate the electrolytic decomposition of water, hydrochloric acid, and other solutions. The unit consists of a cast iron base (H-21225) with insulated binding posts, support rod (H-21360), one burette clamp (H-8022),…

Designed to attach to a tabletop or inverted into a recessed hole for flush mounting. Models are available with either a threaded hole completely through the center or with an unthreaded thru-hole. These die-cast units are supplied without rod. Other sizes are available on request with threaded or…

Smooth Pipe Stem Triangles protect glassware on hotplates and over burner flames

Screw Compressor Clamps are used to control the flow in flexible tubing. The clamps have a machined adjustment screw to permit accurate regulation of the flow. All corners are rounded to prevent cutting of the tubing. The clamps feature brass construction that is plated for corrosion resistance and…

Designed to allow users to mount rod vertically or horizontally. The clamp is cast iron with a black enamel finish.

This clamp is constructed from hardwood with a smooth finish and self-closing spring. The clamp will accept tubes up to 3/4" (19mm) in diameter. Overall length is 7" (178mm).

Adjustable Band Clamps provide a unique and efficient clamping mechanism for objects of any shape and size. The same clamp can be used to handle a gallon container or fit snugly to hold a small thermometer, reducing the need to stock numerous clamp sizes and reducing time spent looking for the…

Fitting on 5/8" (16mm) support rods or smaller, this stamped steel clamp is plated for corrosion resistance and has a steel thumbscrew. The clamp is 9" (229mm)long by 3" (76mm) wide with a center distance 7-1/4" (184mm) between burettes. The unit is designed for use with burettes from 6mm to 16mm…