This tube holder lets you use the Bench-Top Shaker for Mojonnier fat extraction. Each holder accepts up to four flasks, 37 mm in diameter.Maximum of two holders can be shaken at one time. The load max of up to five pounds (2.27 kg) need not be balanced. Unstoppered flasks may be shaken vertically.…

For flasks, resin kettles, etc. Constructed of aluminum exterior for extreme durability Form fitting for even heat distribution Internal operating temperature limit of 450°C. Usable with a splash guard or poncho shield for increased safety and life. Certified by Canadian…

Heating Mantles/Stirrers in Self-Standing Metal Case Eliminates need for mantles with holes or very thin insulation that will accommodate separate stirring devices The optional EMC-4 StirControl II (Thomas number 5912M10) creates and synchronizes a rotating magnetic field within the StirMantle…

The extension support attached to a stable ring stand or distillation rack can be adjusted to any convenient height. Extension supports should be used with smaller aluminum housed heating mantles. Steel ring construction with a 6" shank

Vigorously shakes large funnels Capacity is 80 lbs. The 3D floor shaker eliminates the time consuming and tiring manual shaking of large vessels. The 3D motion circulates liquids up, down, sideways and around making this shaker useful for hemolyzing blood, water pollution analysis or…

Takes one test tube rack containing capped or stoppered tubes from 75 to 200 mm long Use existing test tube racks up to 12" x 5" (305 x 127 mm) Rack is secured in holder by lid which fits over threaded end posts and is adjustable in height above support platform. Knurled nuts are used…

Takes from one to three separatory funnels size 60 to 250 mL Funnel stoppers are held in place by elastic bands. Three adjustable, rubber-covered yokes are used to secure funnels in holder. Spring- loaded release mechanism permits holder to be rotated about shank in 30° increments…

Controls two separate circuits independently Provides precise manual control of heating mantles, tapes, cords and other resistive loads Adjustable output range from 3-100% of rated voltage Use on bench top or mount to lattice work using clamp provided on back panel Will…

Horseshoe-base laboratory stand with 11/16 (17mm) diameter stainless steel mast. Accepts containers up to 9" (229mm) diameter. Designed for durability, these lab stands are designed for the lab bench

Heating mantles are preferred over Bunsen burners or hot plates for organic liquids. They provide even heating (no hot spots) and maximum surface coverage for better temperature uniformity. The Series STM mantle for applications needing more heat. Aluminum Housed Mantles Feature: …

The DigiTrol II uses a 1/16 DIN microprocessor-based, user-selectable control mode temperature control. The control features a digital dual output display set point and process temperature indication. The automatic-tuning feature ensures increased temperature accuracy with minimum overshoot. Easy…

Designed to meet mixing requirements for varying viscosities and volumes Feedback circuitry to maintain speed when viscosity changes Reference circuitry to maintain speed even with voltage fluctuations of ±10% Cord connections between drive motors and controls Stirrers filter the drive…

Manually adjustable; has a percentage-timer design and no sensing element Regulates mantles, tapes and cords, as well as small furnaces, ovens, hot plates, dies and other applications requiring stepless control Can be used on any non-inductive loads to its rated capacity of 1,440 watts …

Heating mantles are preferred to Bunsen burners or hot plates for organic liquids. They provide even heating (no hot spots) and maximum surface coverage for better temperature uniformity. The Series TM spherical flask mantle covers only the flask's bottom half, letting you see its full…

Smooth rotation and repeatability Totally enclosed motors Variable speed motor drives are designed to make the homogenizing process faster, safer and more thorough. These variable-speed drives feature totally enclosed motors. For high-speed operations, the direct drive shaft is…

User friendly microprocessor-based ramping control Microprocessor based PID control Ramp-rate or time-based programming profiles 24 Step program capability Program looping Guaranteed soak (dwell) deviation Auto tuning function allows automatic setting of control…

Versatile, user-friendly shakers that offer reciprocating shaking and mixing for many hours with bench top convenience. Variable speed motor controller - mixing action from gentle, low speed shaking to vigorous, high speed shaking Compact - can fit inside a fume hood for added safety …

Heavy cast iron base accommodates containers up to 406 mm diameter Nickel-plated rod is 762 mm long x 19 mm diameter With tapped holes in base, 1/2-13 U.S. National Coarse thread, for use of additional rods such as 8835C24 and C36.

Medium Duty, Model HST10 Totally enclosed, 1/17 hp, permanent magnet DC motor Direct-drive, with rpm/torque readout and X-Y output Maximum rpm: 2,500 Torque: 1.5 lbs.-in. (1.73 kg-cm) Direct drive provides 20 to 2,500 rpm and 1.5 lb.-in. torque. Available for 120 or 240 V, 50/60 Hz…

Use with heating mantles, tapes, cords, small ovens and other resistive heating loads Digital dual output display for set point and process temperature indication Automatic tuning for accuracy with minimum overshoot Auto cold junction compensation and thermocouple break protection …

Thorough mixing action Variable speed control Speed range of 2-80 rpm Dry Powder Rotator has the drive bar set at a 20° angle so the motion of the rotator closely reproduces the mixing action achieved when mixing by hand, making it useful for working with hard-to-mix powders. Not only is the…

Shakes two flasks simultaneously Operates in cold room or incubator Secures glassware up to 3 1/2” in diameter The WS 180 shaker efficiently agitates small to medium solid phase peptide synthesis flasks. It is also useful for shaking culture flasks and for agitating hard-to-dissolve…

The Series TM Resin Reaction Flask mantle provides even heat distribution to prevent scorching of clear resinous material. One-circuit heat input simplifies temperature control.

Splash Guards can help prevent mantle damage from chemical spillage and improve operating safety when heating liquids. The shield is appropriate for use with low-wattage mantles (Series M and TM) for flasks, glass beakers, steel beakers, resin flasks, and Buchner funnels. A rugged silicone pad…

This mantle's even heat distribution prevents scorching of clear resinous materials. It's one-circuit heat input simplifies temperature control. Resin flask mantles, as well as most other Series O mantles, are available modified to accept vessel drains or other tubulations.

This mantle can accomodate and efficiently heat all types of straight walled metal beakers by preventing contact of heating elements and vessel walls with inner layers of glass fabric. Also available for glass beakers with resilient and pliable interior glass fabric which cradles fragile beakers.…

Mixes multiple samples for better reproducibility Variable speed range: 100 to 2000 RPM Pulsing feature interrupts vortexing to join upper and lower strata for more thorough mixing DC motor with filter control for smoother operation and longer life Set speed and pulsing to identical time for…

Flask Holder lets you shake one to four Erlenmeyer flasks at a time. It will work with uncapped flasks (for gentle shaking), or you can close them with screw caps or tapered stoppers. An elastic band automatically holds the stoppers in place. One or two flask holders can be shaken at once. A…

This mantle helps prevent vapor condensation in the upper half of a flask during distillation of high-boiling materials. The tops are designed for use with Series M, TM, or STM mantles. They protect the flask, the solutions, and the laboratory from drafts, which would disturb the reflux ration…

Selectable settings Orbital offset is 0.070” Maximum capacity is 10 lbs Digital pulse mixer can perform high or low speed vortexing/mixing for a variety of applications. Unit can accommodate a wide range of glassware, racks, well plates or reactor blocks to produce…

Holders for Large Separatory Funnels or Flasks From the upright or fill position, the funnel may be rotated to the 45° or 60° position for shaking and then returned to the upright position for the addition of materials or extracting. The flask may remain in the holder for the entire…

No sharp edges Stainless steel construction Easy-to-use Sample is placed in mill cavity, the two mill halves are pressed together and rotated in opposite directions. Mill is durable and corrosion resistant. Clearance between cutting heads is adjustable; factory preset at…