General purpose gravity eluted column having a PTFE stopcock and reinforced beaded top. Column is constructed using MEDIUM WALL TUBING. Glass wool (not supplied) is used to support column packing. Lower end of the column has a round bottom.

Two piece cold trap style condenser for use with rotary evaporators. Condenser has a 50mm flange on the side, a 35/20 lower ball joint, a 19/38 stopcock plug and removable hose connections using GL-14 threads. Condenser is supplied complete with PTFE centering ring along with plastic caps and…

Manifold is a low cost solution for the concentration of product in 96, 48 or 24 well blocks. Delivers equal amounts of gas to each well to gently speed solvent evaporation. Needles are constructed of stainless steel. 96 well unit has the needed pressed into the block, while the 11, 15, 24 and 48…

For performing quick separations using a vacuum source. All funnels have a lower standard taper inner joint with a sealed in drip tip and an outlet for connection to a vacuum source. All sizes have a Coarse porosity fritted disc.

Adapters permit the connection of standard laboratory dram sample vials directly to the vapor tube or a bump trap of a rotary evaporator. Adapters have a top outer joint of the listed size and a 20-400 G.P.I. thread at the bottom. A PTFE-lined, polypropylene, double-threaded connector attaches the…

Features: S.S. Uprights and Heavy Duty PTFE Coated Aluminum Fittings Provide Maximum Strength and Chemical Durability.  Supports Reactors from 300mL to 5L.  Removable Polyethylene Spill Tray.  Adjustable Middle Support Bracket is Vertically Adjustable. It Accepts Our…

CONDENSERSS, AIR REFLUX, MINUM-WARE® CONDENSERSS, WATER-JACKETED, REFLUX, MINUM-WARE® ADAPTERS, CLAISEN HEAD, MINUM-WARE®, Supplied complete with open-top screw cap (MW-102-22) and PTFE faced silicone septa (MW-104-12). HICKMAN STILL HEADS, MINUM-WARE®

Reflux condenser similar to CG-1213 but with detachable hose connections. Connections are made of polypropylene and provide a safe and easy way of connecting and disconnecting flexible tubing to the condenser. Hose connections have an O.D. of 8mm and an I.D. of 4mm. Supplied complete with two GL-14…

Solid ring with built in clamp for attachment directly to support rod. Available in three sizes. Nickel plated zinc alloy.

Condenser for use in refluxing from 1 to 20mL of solvent in flasks having a capacity of 5 to 50mL. Minimal surface area provides for better yields while providing adequate cooling. The additional hose connection is provided to allow introduction of an inert gas such as nitrogen. Top hose connection…

Laboratory support jacks provide for stable height adjustment and support for items in the lab such as flasks, baths or hot plate stirrers. Top and bottom plates are constructed of anodized aluminum while the support mechanism is made of chrome plated steel.

Base is made of cast iron with a baked black finish. Rod is 10mm O.D. x 600mm (24 ". Available in two sizes.

Rotary evaporator bump trap is used between the vapor tube and evaporation flask on a rotary evaporator to prevent contents of the flask from being drawn into the condenser in the event of “bumping”. Unique elliptical shape provides large trap volume while decreasing the overall length…

Shelf can be attached to any lattice setup using the supplied CG-9250-01 clamp holder. Shelf is 9" wide x 10" deep and anodized green with a neoprene surface to prevent items from slipping off. The 1/2" square support rod is 7.5" long. Square support rod prevents shelf from…

PTFE molded clamps with a steel core can withstand temperatures up to 250° C and are totally chemically resistant and inert.

Condenser has an inner joint and a sealed lower drip tip for drop control. Hose connections have an O.D. of 10mm at the middle serration.

Two piece cold trap style condenser for use with rotary evaporators. Condenser has an additional 19/38 outer joint sealed onto the condenser to allow continuous feed of volumes exceeding the capacity of the evaporating flask.

For your convenience we have combined our oil baths with a controller and bath oil to allow you to order all the items you need with one part number. Ordering with these packages also saves you a minimum of 10% of the purchase price of the individual components. PLEASE NOTE: HOT PLATE MUST BE…

One-Piece Reaction Vessel, 5-Nk, 50mL: 19/22 Outer CN, (1) 10/18 Outer SN, (1) 14/20 Outer SN, and (2) 19/22 Outer SN's. Vessel is graduated from 10 to 50mL. Body outside diameter is 43mm. Equivalent to Mettler EasyMax 102/402 Part # 5116172.Mettler Easymax® is a registered trademark…

Made of Delrin®, the clamp is non-corrosive and will not scratch glass. Can be used to 140°C. Color coded for easy identification. SOLD IN PACKAGES OF 10.

Coil style reflux condenser with tightly wrapped coil providing maximum cooling. Excellent for use with high vapor pressure solvents. Condenser has a top outer standard taper joint and lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

Replacement Vapor tubes compatible with Buchi rotary evaporators. Thread is made for use with standard Combi-Clip. Available in the listed sizes. NOT SUPPLIED WITH COMBI-CLIP. COMPATIBLE WITH BUCHI ROTARY EVAPORATORS, EL MODEL.

Unique one-piece distilling condenser is actually a 75° adapter, highly efficient coil condenser and vacuum adapter in a compact one-piece unit. Available with a choice of three sizes of condensers with uptake inner joint as listed. Top thermometer joint is a 10/30 outer for use with a 3in…

Coil style reflux condenser with a larger diameter jacket and coil, thereby providing maximum cooling capacity, while being shorter in length. Hose connections are on the bottom of the condenser which makes it easier to connect hose/tubing. Jacket has a O.D. of 41mm while the coil O.D. is 8mm.…

Two-piece sublimer consisting of an upper water cooled CONDENSERS and lower flat bottom flask. Sublimate is collected on the inner wall of the CONDENSERS. The two components are assembled by a grease-free o-ring seal which permits the components to be gently separated for maximum product recovery.…

Floor style stainless steel support stand made to accept 12 and 22 Liter CG-1539 half jacketed flasks. Stand is 67in overall height with a depth of 22in. Ring has a diameter of 8 1/2in I.D. and is 28in above floor level. Top of stand has a 39in reinforced riser to support overhead stirrers, clamps etc.

Condenser has a large opening at the top for use with dry ice/acetone or liquid nitrogen. Condenser has a lower inner drip tip joint and hose connections with an O.D. of 10mm at the middle serration. NOTE: See CG-4519 For Solvent Recovery Traps used with Rotary Evaporators.

PTFE adapter allows convenient connection of a Microwave vial to a Rotary Evaporator Bump Trap having a standard taper joint size. Lower portion incorporates a threaded black Acetal compression cap that is slotted to accept the flange fitting on the vial.

Chemglass 135mm round top ANALOG hot plate stirrer system. Hotplates feature many exclusive features and improved safety enhancements. The 135mm diameter heater top is scratchproof and chemically-resistant. The back corner of the housing has an M8 female thread to accept a vertical support rod. …

Soxhlet type extraction apparatus used for continuous extraction of solids with a suitable solvent. Extractor uses paper or CG-1372 glass thimbles. Condenser has an enlarged uptake tube to improve condensing capacity. Complete apparatus consists of an Allihn condenser, extractor and flat bottom flask.

Condenser has a standard taper outer joint at the top and a lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

Micro size gas dispersion tube having a frit 7mm O.D. x 12mm. Stem is 6mm O.D. x 100mm long.